Canon Maxify Mb2020 User Guide
Have a look at the manual Canon Maxify Mb2020 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Problems with the Machine The Machine Cannot Be Powered On Cannot Connect to Computer with a USB Cable Properly Cannot Communicate with the Machine with USB Connection LCD Cannot Be Seen At All An Unintended Language Is Displayed on the LCD Print Head Holder Does Not Move to the Position for Replacing Printer Status Monitor Is Not Displayed 981
The Machine Cannot Be Powered On Check1 Press the ON button. Check2 Make sure that the power plug is securely plugged into the power cord connector of the machine, then turn it back on. Check3 Unplug the machine from the power supply, then plug the machine back in and turn the machine back on after leaving it for at least 2 minutes. If the problem is not resolved, contact the service center. 982
Cannot Connect to Computer with a USB Cable Properly Printing or Scanning Speed Is Slow/Hi-Speed USB Connection Does Not Work/"This device can perform faster" Message Is Displayed If your system environment is not fully compatible with Hi-Speed USB, the machine will operate at a lower speed provided under USB 1.1. In this case, the machine operates properly but printing or scanning speed may slow down due to communication speed. Check Check the following to make sure that your system environment supports Hi- Speed USB connection. • Does the USB port on your computer support Hi-Speed USB connection? • Does the USB cable or the USB hub support Hi-Speed USB connection? Be sure to use a certified Hi-Speed USB cable. We recommend that the cable is no longer than around 10 feet / 3 meters. • Does the operating system of your computer support Hi-Speed USB connection? Obtain and install the latest update for your computer. • Does the Hi-Speed USB driver operate properly? Obtain the latest version of the Hi-Speed USB driver compatible with your hardware and reinstall it on your computer. Important • For details on Hi-Speed USB of your system environment, contact the manufacturer of your computer, USB cable, or USB hub. 983
Cannot Communicate with the Machine with USB Connection Check1 Make sure that the machine is turned on. Check2 Make sure that the USB cable is connected properly. See Connecting the Machine to the Computer Using a USB Cable to connect the USB cable properly. Check3 Do not start up IJ Network Tool while printing. Check4 Do not print while IJ Network Tool is running. Check5 Make sure that Enable bidirectional support is selected in the Ports sheet of the properties dialog box of the printer driver. How to Open the Printer Driver Setup Window 984
LCD Cannot Be Seen At All • If the POWER lamp is off: The machine is not powered on. Connect the power cord and press the ON button. • If the POWER lamp is lit: The LCD may be in the screen-saver mode. Press one of the buttons on the operation panel. 985
An Unintended Language Is Displayed on the LCD Select the language you want to be displayed according to the following procedure. 1. Press the HOME button and wait for about 5 seconds. 2. Select Setup on the HOME screen. LCD and Operation Panel 3. Select Device settings , then press the OK button. 4. Press the button 4 times, then press the OK button. 5. Use the button to select the language for the LCD, then press the OK button. 986
Print Head Holder Does Not Move to the Position for Replacing Important • The print head holder moves to the position for replacing only when an ink tank runs out of ink. If no ink tanks run out of ink, the print head holder does not move even though you open the front cover. Check1 Is the POWER lamp off? Check if the POWER lamp is lit. The print head holder will not move unless the power is on. If the POWER lamp is off, close the front cover and turn the machine on. While the POWER lamp is flashing, the machine is initializing. Wait until the POWER lamp stops flashing and remains lit, and then open the front cover again. Check2 Is an error message displayed on the LCD? Close the front cover, follow the Support Code (error number) displayed in the error message to resolve the error, and then reopen it. For details on how to resolve the error, refer to Support Code List . Check3 Has the front cover been left open for 60 minutes or longer? If the front cover is left open for more than 60 minutes, the print head holder moves to the position to protect it to prevent the print head from drying out. Close and reopen the front cover to return the print head holder to theposition for replacing. 987
Printer Status Monitor Is Not Displayed Check Is the printer status monitor enabled? Make sure that Enable Status Monitor is selected on the Option menu of the printer status monitor. 1. Open the printer driver setup window. How to Open the Printer Driver Setup Window 2. On the Maintenance sheet, click View Printer Status . 3. Select Enable Status Monitor on the Option menu if it is not selected. 988
Problems with Installation/Downloading Cannot Install the MP Drivers Easy-WebPrint EX Does Not Start Up or Easy-WebPrint EX Menu Does Not Appear How to Update MP Drivers in Network Environment Uninstalling IJ Network Tool 989
Cannot Install the MP Drivers • If the installation does not start even after the Setup CD-ROM is inserted into your computer'sdisc drive: Start the installation following the procedure below. 1. Select items as shown below. ◦ In Windows 8.1 or Windows 8, select the Explorer icon in Taskbar on Desktop , then select Computer from the list on the left. ◦ In Windows 7 or Windows Vista, click Start then Computer . ◦ In Windows Vista, click Start then Computer . ◦ In Windows XP, click Start then My Computer . 2. Double-click the CD-ROM icon on the displayed window. If the contents of the CD-ROM are displayed, double-click MSETUP4.EXE. If you cannot install the MP Drivers with the Setup CD-ROM, install them from our website. Note • If the CD-ROM icon is not displayed, try the following: • Remove the CD-ROM from your computer, then insert it again. • Restart your computer. If the icon is not yet displayed, try different discs and see if they are displayed. If other discs are displayed, there is a problem with the Setup CD-ROM. In this case, contact the service center. 990