Panasonic Kx-T123211d Installation Manual

							Card Installation 
1. To protect the printed circuit board from static 0 Insert the optional card with holding a levers of 
electricity, first discharge any body static by the card into the KX-T123211 surely. 
touching the metal board. Do not touch parts on the card. 
2. Loosen the screws to remove the metal board. 
3. The location of the optional cards for the 
KX-Tl23211 is shown in the following. 
(KX-T123292) 
$1 
l!h _ --__ I \ 
\ I I 
// / (KX-T123241)  metal board 
v 
Screws - 
0 
3 
P 
2 - 25  
						

							OPTION (cont.) 
To add eight extensions (jack number 17 through 
24), use the optional expansion card 
KX-T123270. 
To add four extensions (jack number 17 through 
20), use the optional expansion card 
KX-T123271. 
1. Insert the expansion card KX-Tl23270 or 
KX-Tl23271 into the KX-Tl23211 
2. Insert connector to the KX-T123270 or 
KX-T123271 as shown at right. 
Cable Pin Numbers to be connected 
See page 2-10. 
0 Mis-connection may cause the KX-T123211 
to operate improperly. 
See “During Installation” page 6-l and 
“During Connection” page 6-2 before 
connecting. 
To Extensions (jack number 17 through 20, 
or 17 through 24 ) 
w= 
Expansion/card 
KX-T123270 . . jack number 17 through 24 
KX-T123271 . . . 
jack number 17 through 20 
To add eight extensions (jack number 25 through 
32), use the optional expansion card 
KX-T123270. 
To add four extensions (jack number 25 through 
28), use the optional expansion card 
KX-T123271. 
1. Insert the expansion card KX-T123270 or 
KX-T123271 into the KX-T123211. 
2. Insert connectorto the KX-T123270 or 
KX-T123271 as shown at right. 
Cable Pin Numbers to be connected 
0 
See page 2-10. 
Mis-connection may cause the KX-T123211 to 
operate improperly. 
See “During Installation” page 6-1 and 
“During Connection” page 6-2 before 
connecting. 
To Extensions (jack number 25 through 28, 
or 25 through 32 ) 
Expansion card 
KX-T123270 . . . jack number 25 through 32 
KX-T123271 . . . jack number 25 through 28 
2-26  
						

							To add four Central Office Lines (CO 9 
through 12), use the optional expansion 
card KX-Tl23280. 
1. 
2. 
. 
0 Insert the expansion card KX-T123280 into 
the KX-Tl23211. R : Ring 
T :Tip 
Vi 
ack (CO) 
Insert the modular plug of the telephone 
line cord (2-conductor wiring) into the 
modular jack on the KX-T123280. 
Mis-connection may cause the KX-T123211 
to operate improperly. 
See “During Installation” page 6-l and 
“During Connection” page 6-2 before 
connecting. 
To Terminal Board or Modular Jacks + 
)rn the Central Office (CO). 
Use 2-conductor wiring cord 
To add two Central Office lines (CO9 and 
COlO), use the optional expansion card 
KX-Tl23281. 
1. 
2. 
0 Insert the expansion card KX-T123281 
into the KX-T123211. 
Insert the modular plug of the telephone 
line cord (2-conductor wiring) into the 
modular jack on the KX-T123281. 
Mis-connection may cause the KX-Tl23211 
to operate improperly. 
See “During Installation” page 6-l and 
“During Connection” page 6-2 before 
connecting. 
To Terminal Board or Modular Jacks 
from the Central Office 
(CO). 
R :Ring 
T : Tip 
View of TEL Jack (CO) 
b 
co9 
co10 
\ - 
0 
s 
P 
Use 2-conductor wiring cord 
2-27  
						

							OPTION (cont.) 
When you remove the card, 
pull upward. 
To add four Central Office lines (CO5 through 8), 
use the optional expansion card KX-T123280. 
Insert the expansion card KX-T123280 into 
the KX-T123211. 
Insert the modular plug of the telephone 
line cord (2-conductor wiring) into the 
modular jack on the KX-T123280. 
Mis-connection may cause the KX-T123211 
to operate improperly. 
See “During Installation” page 6-l and 
“During Connection” page 6-2 before 
connecting. 
R : Ring 
T 
: Tip 
View of TEL Jack (CO) 
co5 
CO6 
co7 
CO8 
To Terminal Board or Modular Jacks @ 
from the Central Office (CO). 
Use 2-conductor wiring cord 
2-28  
						

							To connect the optional DSS Console (KX-T123240 or KX-T61640), the optional DSS Console card (KX-T123241) 
is required. 
The DSS Console (KX-T123240 or KX-T61640) needs a paired Telephone (EMSS Proprietary Telephone) for 
proper operation, because the DSS console cannot work by itself. 
The EMSS Proprietary Telephone (such as KX-T123220, KX-T123230, KX-T123235, KX-T123250) is required as 
the paired telephone for dialing, storing, etc. 
Place the KX-T123240 or KX-T61640 and the paired telephone side by side on your desk. 
1. Insert the DSS Console card (KX-Tl23241) into the 
KX-Tl23211 
2. Insert the modular plug of the console line cord 
(4-conductor wiring) into the modular jack on the 
KX-T123241. 
“DSS” is written on the Card. 
Notes: 
Dl : Data 1 D2 : Data 2 
View of TEL Jack 
k 
Console 1 
Console 2 
Up to 2 KX-T123240’s or KX-T61640’s can be connected 
to the KX-T123211. Each console requires its own 
paired telephone. 
KX-Tl23240 or KX-T61640 can not be connected in 
pair with a standard telephone. 
The max. length of the console line cord (twisted 
cable) that connects the KX-T123211 with the DSS 
Console is shown below. DSS Console Ca{d KX-T123241 
- 
0 
s 
P 
- 
4conductor wiring is 
h tp 6”,q;i;:;f;l;he 
=7----l 
Pair Telephone 
(EMSS Proprietary 
Telephone) 
. 
Pair DSS Console 
KX-T123240 
KX-T61640 
26 AWG: Under 460 feet 
24 AWG: Under 750 feet 
22 AWG: Under 1180 feet 
When using the KX-T123240 or KX-T61640, program 
must be done. Refer to “Paired Telephone Assignment 
for DSS Console” page 3-10. 
2-29  
						

							OPTION (cont.) 
Enables a standard telephone installed outside the premise to work as an extension through public orprivate lines. 
To avail of this feature, an optional Off Premise Extension Unit KX-T123286 is necessary aside from KX-T123285. 
1. Insert the Off Premise Extension Card 
KX-T123285 into the KX-T123211. 
2. Insert the connector from the KX-T123286 to 
the Off Premise Extension Card. Extension Card 
Connector 
(24 pin) 
 
3. 
n 
4. Connect the frame of the KX-T123286 to 
earth ground properly to protect the unit. 
5. Plug in the AC Power cord from the 
KX-T123286. 
6. Turn on the Power Switch on the 
KX-T123286. 
l The Power indicator will be lit.  Insert the modular plug of the Standard 
Telephone Line (2conductor wiring) into the 
modular jack on the KX-T123286. 
Power Switch 
“OPX” is written on the Card. 
Off Premise Extension Unit + 
KX-T123286 Standard Telephone 
Jack number 32 
c 
To earth 
ground Jack number 31 
Use 2-conductor wiring cord 
L I 
Programing must be done to use this feature. W 
Refer to “Off Premise Extension” on page 3-45. . 
Primary Power Fuse, (800 mA, 250 V) xl: 
If the Power Indicator light goes off, the Primary Power 
Fuse must be replaced after remove the cause. 
2 - 30  
						

							This feature enables to access System from outside of System and then call to extension or outside line. 
For example, you can call the desired extension directly by dialing the extension number following the regular CO 
number. 
Optional KX-T123292 card is necessary to program KX-T123211 to send Outgoing Message when called with this 
feature. 
1. Insert the Direct Inward System Access Cards A 
and B into the KX-T123211. 
“DISA-A” and “DISA-B” are written 
on each Card. Direct Inward System Access Cards KX-T 123291 
DISA-B Card 
DISA-A Card 
An Outgoing Message can be sent from the KX-T123211 when a call is received using the “Direct Inward System 
Access” feature. 
1. Insert the Outgoing Message Card KX-T123292 
into the KX-Tl23211. Outg 
Card 
“OGM” is written on the Card. 
For how to record 
OUtgOing Message, refer to “Outgoing Message” on page 4-67. 
2 - 31  
						

							OPTION (cont.) 
By using the data terminal connected to RS-232C on KX-T123211 or remote data terminal connected to KX-Tl23211 
through MODEM, diagnosis of KX-Tl23211 system can be done. 
Remote administration 
H The following optional cards are necessary. 
0 Diagnostic Card KX-T123295 
0 Direct Inward System Access Cards 
KX-T123291 
(See page 2-31) 
0 MODEM Card KX-T123296 
(See page 2-32) 
Data terminal equipment 
KX-Tl23211 
On-site administration 
RS232C Cable n The following card is necessary. 
0 Diagnostic Card KX-Tl23295 
Data terminal equipment 
1. Insert the Diagnostic Card KX-T123295 into the 
KX-T123211. KX-T123211 
jgfxp!g 
“DIAG”is written on the Card. 
This card is necessary for data communication 
to execute confirmation or registration of System data or diagnosis of 
the System using remote data terminal equipment. 
1. Insert the MODEM Card KX-T123296 into the 
KX-T123211. 
MODEM Card 
KX-T123296 
 / 
“MODEM” is written on the Card. 
2 - 
32  
						

							For installing the doorphone, use the Optional Doorphone Adaptor (Use the KX-T30860D only). 
Installation of the doorphone Installqtion of the Doorphone Adaptor 
Loosen the screw to 
separate the 
doorphone into 2 
halves. How to install the Doorphone Adaptor into the 
KX-Tl23211. 
1. Connect a 4-conductor modular connector to 
the doorphone adaptor. 
Install the lower case 
to the wall with 2 
screws. 
l 2 kinds of screws 
are included. Please 
choose according to 
your wall type. See 
the followings. doorphone adaptor (KX-T30860D) 
4-conductor wiring 
been fixed to the wall. 
w-------When you wish to install the 
doorphone directly to the wall. 
2. 
3. Connect the wires 
from the terminal 
box to the screws 
located in the 
upper case. 
to the terminal box 
(See page 2-34) 
4. Secure both halves together and ,re-install the 
screw. 
3. Install the doorphone adaptor into the 
adaptor compartment. 
After drawing a CPU Card, insert the adaptor 
connector into connector on the CPU Card 
(circuit board). 
Adaptor Connector 
Connector CPU Card 
2-33  
						

							OPTION (cont.) 
(4 Connect the doorphone adaptor to the terminal box using a 4-conductor modular connector. 
(W Connect the wires of doorphone 1 to the red and green screws of the terminal box. 
(C) Connect the wires of doorphone 2 to the yellow and black screws of the terminal box. 
:or 
. 
Doorp 
0 
Doorphone Wiring 
hone 1 (KX-T30865) 
YELLOW 
RED Doorphone 2 (KX- 
BLACK 
GREEN ,T30865) 
The max. length of the telephone line cord (twisted cable) that connects the KX-T123211 and the doorphone 
(KX-T30865) is shown below. 
26 AWG: Under 230 feet 
24 AWG: Under 370 feet 
Automobile type batteries which customer supplied is available as a backup power supply of the FX-T123211 
to operate all the features in the event of power failure. 
For connecting automobile type batteries, use the Optional Battery Adaptor KX-A26. 
1. Connect the Battery Adaptor KX-A26 to automobile type batteries. 
2. Connect the Battery Adaptor KX-A26 to the Battery Backup Connector of the Kx-TI 23211. 
KX-T123211 
0 Consisting of two 12 VDC 
(24 VDC)