Panasonic Kx-T123211d Installation Manual

							OPTION 
The optional cards are following. 
Expansion Cards 
DSS Console Card 
Off Premise Extension 
(OPX) Card 
Off Premise Extension 
(OPX) Unit Model No. 
KX-T123270 
KX-Tl23271 
KX-T123280 
KX-T123281 
KX-T123241 
KX-T123285 
KX-T123286 
Description 
This card adds 8 Extensions. 
This card adds 4 Extensions. 
This card adds 4 CO’s. 
This card adds 2 CO’s. 
The DSS Console requires the DSS 
Console Card for the operation. 
Enables a standard telephone 
installed outside the premise to work 
as well as an extension. 
Reference Page 
2-26 
2-26 
2-27, 2-28 
2-27 
2-29 
2-30 
Direct Inward System 
Access (DISA) Cards 
Outgoing Message Card 
KX-T123291 Enables to access system from 
outside of system as well. 
2-31 
KX-T123292 In case access from outside by 
installed this card, enable to send 
the recorded message instead of 
dial tone. 2-31 
Diagnostic Card KX-Tl23295 
MODEM Card KX-T123296 Diagnosis of system can be done 
This card is necessary for data 
communication with remote. 2-32 
2-32 - 
s 
a 
2-15  
						

							OPTION (cont.) 
4 CO Lines (initial) 
L 2, 4 or 6 CO Lines can be added. 
n The following optional cards are necessary. 
l To add the 2 CO Lines - - - . * - 
Expansion card KX-Tl23281 
l To add the 4 CO Lines - - - - - - Expansion card KX-Tl23280 
l To add the 6 CO Lines - - * - - - 
Expansion card KX-T123280 (2 cards) 
16 extensions (initial) 
L 4, 8, 12 or 16 extensions can be added. 
n The following optional cards are necessary. 
l To add the 4 extensions - - - - = 
Expansion card KX-T123271 
0 To add the 8 extensions - - - - - 
Expansion card KX-T123270 
0 To add the 12 extensions - . - - 
I: Expansion card KX-Tl23271 
Expansion card KX-Tl23270 
0 To add the 16 extensions - - = - Expansion card KX-T123270 (2 cards) 
2- 16  
						

							The DSS console (KX-T123240 or KX-T61640) needs a paired telephone (EMSS Proprietary Telephone) for 
proper operation, because the DSS console cannot work by itself. 
The DSS console let you dial to the extension by simply pushing the DSS Button. 
The programmable feature buttons on the DSS console let you access various features of the KX-T123211 and 
speed dialing using the CO line in addition to the numbers programmed into the KX-T12321 l’s memory. 
An EMSS Proprietary Telephone (such as KX-T123220, KX-T123230, KX-T123235, KX-T123250) is required 
as the paired telephone for dialing, storing, etc. 
n The following optional DSS Console and card are necessary. 
l DSS Console KX-T123240 (32 DSS’s, 16 Feature buttons) 
l DSS Console KX-T61640 (16 DSS’s, 16 Feature buttons) 
0 DSS Console Card KX-T123241 
Paired Telephone 
DSS Console 
(EMSS Proprietary 
KX-T123240 
Telephone) 
KX-T61640 
Pair 
When using the KX-T123240 or KX-T61640, programing must be done. Refer to 
“Paired Telephone Assignment for DSS Console” page 3-l 0. 
2-17  
						

							OPTION (cont.) 
This feature enables access system from outside. 
For example, you can call the desired extension directly by dialing the extension number and the desired CO line 
directly by dialing the number 9 or trunk group access number, following the regular CO number. 
KX-T123211 
I I Telephone Line 
n The following optional card is necessary. 
0 Direct Inward System Access Card KX-T123291. 
n When execute a remote administration, the following optional card is necessary with DISA cards. 
l MODEM Card KX-T123296 
n If outgoing message is necessary when receive a call from CO line, the following optional card is necessary with 
DISA cards. 
0 Outgoing Message Card KX-T123292 
n Programing must be done to use this feature. 
Refer to “CO Mode (Normal / Direct In Line / Direct Inward System Access) Assignment” on page 3-67 and 
“Direct Inward System Access (DISA)” on page 3-42. 
n A rotary phone will not function. 
2-18  
						

							Operation 
From outside of System 
0 
Make a call 
to the line 
which is 
beforehand 
p-yyFAed 
Line on the 
. KX-’ 
Dial tone (First dial tone) will be 
heard. 
If the Outgoing Message Card is 
installed to KX-T123211, outgoing 
message will be heard instead of dial 
tone. (refer to page 2-21) 
3211. 
. To call to Extension 
n If Security Type is set to None Security or 
Trunk Security. 
Dial extension number 
(100 through 199) 
n If Security Type is set to All Security. 
@J.. 
. 
. 
I 
. . . . . . 
 
Dial user You will hear 
security code second dial 
(60000 through tone 
69999) Dial extension 
number (100 
through 199) 
. To call to CO line 
n If Security Type is set to None Security. 
Dial “8” Dial trunk 
9 roup number You will hear D$&ne 
CO dial tone 
1 through 8) 
0 
You may-dial automatic line access 
number “9” instead of “8” and trunk 
group number. 
n If Security Type is set to Trunk Security 
or All Security. 
Dial user Dial “8” 
tEzrity 
(60000 through 
69999) Dial trunk You will hear Dial phone 
group CO dial tone number 
number 
(1 through 8) 
l You may dial automatic line access 
number “9” instead of “8” and trunk 
group number. 
2- 19 
- 
I 
q When disconnect CO line after finish CO 
to CO calling. 
Dial “st” 
You will hear 
first or 
second dial 
1 
tone 
To access the System 
Dial ‘I*” Hang up 
(Remote Administration) 
Dial remote 
security code 
(70000 through 79999) 
0 
Data Terminal equipment display as 
follows. 
; Welcome to KX-TI 23211 remote administration 
ver 2.0 Panasonic CO., LTD 
;** Jan.1.1988 12 
: 00’ AM ** 
; The “HLP” displays command informations 
; > E1 
Please refer to the manual “EVVREMOTE 
PROGRAMMING NANUAL”. 
Note 0 
0 Dial Security Code or Extension number 
or CO line access number in 10 seconds 
after outgoing message is finished or first, 
second dial tone are heard. 
If Outgoing Message Card is installed and 
outgoing message is not recorded, Direct 
Inward System Access (DISA) doesn’t 
work. 
When operator is registered in System, 
call to operator automatically and When 
operator is not registered in System, call 
to general Extension. 
When dial the wrong security code 3 
times, the call is disconnected. 
It is necessary for security code to be 
programmed beforehand. 
DISA can receive up to 2 calls and can’t 
receive more than 3 calls at the same time. - 
0 
s 
s  
						

							OPTION (cont.) 
Retry Function 
Time Over of Receiving Call 
When press the “ * ” button while hearing a ringback 
tone, reorder tone, busy tone or talking over the 
telephone, back to the situation of dial tone and you 
can call again, but you can’t retry while calling CO 
line to extension with DISA. When time over of receiving call, the call moves as 
follows. 
When outgoing message is registered. 
Example 
I Dial to KX-T123211 with DISA. 
I 
When Outgoing Message Card is not installed 
(If Security Type is set to None Security or Trunk 
Security.) Outgoing message will be heard 
Dial to KX-Ti 23211 with DISA. 
& (If you don’t dial in 10 secinds after outgoing 
message is finished. or dial the wrong number.) 
I . I I 
First dial tone will be heard. 
I 
w- ~ 
Dial to extension. 
+ 
When dial the wrong number or call another 
(If Security Type is set to All Security.) 
Dial to KX-T123211 with DISA. 
( 1  First dial t;;z;; be heard. 
Dial the User Security Code (60000 through 
l-4 Second dial tone will be heard. 
I I 
I 
* I 
I I Dial to extension. 
When dial the wrong number or call another 
n 
n If press the q button in case of as follows, 
the call will be disconnected. 
0 While outgoing message is heard. 
0 While dial tone (1st or 2nd) is heard. 
0 While Silence after outgoing message is 
finished. 
When Outgoing Message Card is installed and 
outgoing message is not recorded, the call 
which is sent to DISA CO is sent to general 
extension. 
I 
+ (When operator is registered in System) 
4 
Call the Operator 
+ (When operator is not registered in System) 
I”“‘““‘““‘;“‘“‘*“‘“1 
If the a button is not pressed in 10 seconds, 
the call will be disconnected. 
If the 18/ button is pressed in 10 seconds, First 
dial tone will be heard and you can enter. 
When Outgoing Message Card is not installed. 
(If you don’t dial in 10 seconds) 
q1 
If the 
q button is not pressed in 10 seconds, 
the call will be disconnected. 
If the m button is pressed in 10 seconds, First 
dial tone will be heard. 
2 - 20  
						

							To extend the call duration time 
while calling CO line 
l If you call to any outside line using DISA, the KX- 
T123211 will disconnect the call from the line 
after 10 minutes. For changing the time, see “CO 
to CO Duration Time Limit” on page 3-30. 
3 beeps tone will be heard every 5 seconds for 15 
seconds before the call is disconnected from the 
. 
line. 
If you press button except the 
q button in 15 
seconds, the call duration time can be extended 5 
minutes. 
1 beep tone will be heard when button except the 
q is accepted. For changing the time, see 
“Direct Inward System Access” on page 3-42. 
Outgoing Message 
Enable to send outgoing message to the telephone 
called with DISA. 
Refere to page 4-66 as to the registration of 
outgoing message. 
Example 
This is ABC company. Would you dial to your 
desired post’? Operator number is 00, Business 
is 100 and Account’s department is 180. 
Operator 
lf operator is registered in System Program and 
outgoing message has been recorded, the call is 
sent to operator automatically. 
0 When time out 
0 When the called extension doesn’t answer in 
20 seconds. 
0 When the called extension is set to Do Not 
Disturb. 
I Security Code 
Security Code is used to protect from abusing 
system with DISA. 
There are User Security Code and.Remote Security 
Code in Security Code. 
User Securitv Code 
User Security Code is used when dial to extension 
or CO line with DISA. 
n Security code can be set by 3 modes as follows. 
None Security 
This is the mode in which Security Code is 
unnecessary when dialing both extension and 
outside line. 
Trunk Security 
This is the mode in which Security Code is 
necessary when dialing an outside line, but 
unnecessary when dialing an extension. 
All Security 
This is the mode in which Security Code is 
necessary when dialing both extension and 
outside line. 
w User Security Code can be set by 4 types. 
0 User Security Code 1:60000 
0 User Security Code 4:60000 
-II 
enable to enter last 4 
digits with program 
Remote Security Code mode 
Remote Security Code is used when Remote 
Administration is done with DISA. 
n Remote Security Code can be set by 1 type. 
0 Remote Security code:70006 
-II 
enable to enter last 4 
digits with program 
LIST OF TONES 
mode 
IseC 
1st dial tone I-; I 
I , 
I I 
2nd dial tone 
Reorder tone 
Busy tone 
Ringback tone 
Disconnect 
warning tone 
Prolong 
: - : 
I 
I ; I i 
I 
confirmation tone 1 l-l 1 2 - 21  
						

							OPTION (cont.) 
Enables a standard telephone installed outside the premise to work as an extension through public or private rate 
lines (under 6 miles). 
KX-T123286 
I Standard Telephone 
Jack number 32 
Jack number 31 
KX-Tl23211 
n The following optional card and unit are necessary. 
l Off Premise Extension (OPX) Card KX-T123285 
l Off Premise Extension (OPX) Unit KX-T123286 0 OPX can’t function with Doorphone. 
l The Ring Tone from extension or CO line are as follows. 
n Programing is necessary to use this feature. 
Refer to “Off Premise Extension” on page 3-45. 
The doorphone can be installed to the KX-Tl23211. 
Doorphone 1 Doorphone 2 
n The following optional doorphone and adaptor are necessary. 
0 Doorphone KX-T30865 
0 Doorphone adaptor KX-T30860D (only) 
2 - 22  
						

							By using data terminal connected to RS-232C on KX-Tl23211 or remote data terminal connected to KX-T123211 
through MODEM, diagnosis of KX-T123211 system can be done. 
Remote Administration 
Telephone Line 
Data terminal equipment 
KX-T123211 
n The following optional cards are necessary. 
0 Diagnostic Card KX-T123295 
0 Direct Inward System Access Cards KX-T123291 
l MODEM Card KX-T123296 
On-Site Administration 
Data terminal equipment 
KX-T123211 
w The following card is necessary. 
0 Diagnostic Card KX-1123295 
, 
2 - 23  
						

							OPTION (cont.) 
KX-T12321 l’s diagnostic feature has two command systems. 
One is a “Test commands” system which actually executes the diagnostic process, and the 
other is a “Control commands” system which controls the state of diagnosis. 
1. All components test 6. DISA module and OGM card test 
The system consecutively executes test items as 
following description. 
2. 
CPU card and system control circuit test 
The KX-T123211 system allovys you to test the 
DISA-A card which controls all the DISA system, 
the DISA-B card which consists of crosspoint 
switches etc. and the OGM card which consists 
of voice processors etc. 
The system executes the test of i/o circuit, real 
time clock chip on the CPU card and i/o circuit on 
each card. 
This is the basic test on the KX-T123211 
system. 
You should execute this test at first, because, if 
i/o circuits have defects, the following test items 
will be meaningless. 
3. 
Cross point card test 
The system executes the test of DTMF generator 
and receivers at first, and executes the test of the 
cross point switch circuits. 
4. CO 
card test 
This test allows you to check of relays, analogue 
switches, bell detection circuits CPCLOOP current 
detection circuits and bidirectional amplifiers on 
the CO card no. 1 through no. 3. 
5. Line circuit (LC) card test 
7. OPX interface card and unit box test 
Off premise extension (OPX) test allows you to 
check the OPX interface card which consists of 
the bi-directional amplifiers and analogue 
switches, and the OPX unit box which consists of 
hook detectors, ring trip circuits, loop current 
sources, ringing generators and so on. 
6. 
MODEM card test 
This test allows you to check the digital and 
analogue circuits on the MODEM chip with 300 
bps and 1200 bps communication speed. 
You can use this test on the on-site diagnostic 
mode only. 
The system executes the test of loop current 
sources, ringing relays, hook detection circuits 
and ring trip circuits on each LC card. 
And it will execute the check of data 
communication capability on the LC cards and 
DSS console interface card. 
2 - 24