Panasonic Kx-T123211d Installation Manual

							CONNECTION 
l The Power Switch of the KX-T123211 must be off during wiring. 
After all the wiring are completed, turn the Power Switch ON. 
o Mis-Wiring may cause the KX-T123211 to operate improperly. 
Refer to “During Installation” page 6-l and “During Connection” page e-2. 
l 50 pin configuration and Color coding 
(Refer to page 2-10.) 
l Max. length and kind of wire 
(Refer to pages 2-8; 2-29, 2-30 and 2-34.) 
l Insertion of Option Card 
(Refer to page 2-25.) 
0 Connection of printer 
(Refer to page 2-12.) 
0 If an extension does not operate properly (for example : The LCD of the KX-T123235/KXYT123230/KX-T61 631/ 
KX-T61630/KX-T30830 does not display properly.), disconnect the telephone from the extension line and then 
connect again, or turn OFF the 
power switch of the KX-T123211 and then ON again. 
l This product is equipped with a 3-wire grounding type plug, a plug having a third (grounding) pin. This plug 
will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug 
into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the 
grounding-type plug. 
l In areas of frequent electrical storms and/or power failures, we recommend for additional equipment 
protection, surge protectors such as TELESPIKE BLOK MODEL TSB (TRIPPE MFG. CO.), SPIKE BLOK 
MODEL SK6-0 (TRIPPE MFG. CO.), Super MAX’” (PANAMAX) or MPl (ITW LINX). 
Paging Speaker 1 
Paging Speaker 2 
AC Surge Protector  0 Avoid using the same AC outlet for 
office equipment and KX-T123211. 
Use dedicated AC outlet only. 
.Batterv Adaotor KX-A26 
Automobil 
type batteries 
I Radio _ 
0 Consisting of two 12VDC (24VDC) 
I . 
2-5  
						

							r__________-___-__________, I I 
I I 
I 
I 
I I 
I I 
I 
I 
I I 
I I 
I I 
: 2 ; 
_--_ 
. r----------- ____---___---, I I 
I 
I 
I I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
i KX-Tl23240 
KX-T61640 ; 
i___________________--_i 
(one pair) 
c 
Standard 
Telephone 
Data Terminal 
Phone 
& t 
i 
0 
‘;I 
Off Premise Extension Unit Standard Telephone 
(C.O. Surge Protector) 
2 of 32 extensions 
Initial 
12 CO Lines 
toC06 1 
r ----~-~~~---~~---__--~~~ 
7 
I 
toco7 - 1 
I 
I toC08 i 
I 
I 
I 
I toco9 I 
I to co 10 addition I 
I 
I 
I taco 
11 
I 
I 
to co 12 _ I 
I I 
I 
L_______________________-_i 
32Extension Lines 
16 Extension Lines=lnitial 
~---~~~--~--~~----~~~--, 
116 Extension Lines.addition 
l 
L_-____________________~ 1 
(two pair) 
KX-T30830 
:two pair) 
KX-T30820 
(two pair) 
KX-T30850 
:twq pair) 
KX-T30825 
KX-T61631 
(two pair) 
KX-T61630 
(two pair) 
KX-T61620 
(two oair) 
KX-T61650 extension connected 
to jack number 1 
KX-Tl23230 or KX-Tl23235 
0 Extension connected jack 
number 1 must always be a 
KX-Tl23230 or KX-T123235. 
KX-T123235 
KX-Tl23220 
KX-T123250 
Telephone 
with Answering 
Machine I ; 
l Parallel connections of telephone I I : need Optional Cards or Adaptor 
L--J is impossible. 
0 When the KX-T30830 is connected to the KX-T123211, enter 
“DSS Number” or “One Touch Dialing Button” to DSS button. 
See page 4-61. 
2-6  
						

							l We recommend that telephone CO jack is used RJll. 
Insert the modular plug of the telephone 
line cord (2-conductor wiring) into the 
modular jack on the KX-T123211. 
R : Ring 
T : Tip 
View of TEL Jack (CO) 
To Terminal Board or Modular Jacks 
G7 
from the Central Office (CO). 
 
Use 2-conductor 
wiring cord 
l Mis-connection may cause the KX-T123211 to operate improperly. 
See “During Installation” page 6-1 and “During Connection” page 6-2 
before connecting. 
co 
co 
co 
co 
, 
2-7  
						

							To connect jack number 1 through 8 and 9 
through 16, insert connector to the 
KX-T123211 
as shown right. 
Jack no 
K K Jack no 
1 through 8 
- 9 through 16 
Connector type 
50 
pin (Amphenol 57JE 
series or the equivalent) 
To Extensions (jack number 1 through 8 ) 
+ 
To Extensions (jack number 9 through 16 ) * 
Cable Pin Numbers to be connected 
See page 2-10. 
l The max. length of the extension line cord (twisted cable) that connects the KX-T123211 and the extension 
is shown below. 
26 AWG: Under 
460 feet 
24 AWG: Under 
750 feet 
22 AWG: Under 1180 feet 
6 AWG: Under 2290 fe 
0 
0 
24 AWG: Under 3700 feet I 
I 
22 AWG: Under 5900 feet I 
,I 
I . 
If a telephone or answering machine with an A-Al relay is connected to the KX-Tl23211, set the A-Al 
relay switch of the telephone or answering machine to OFF. 
Mis-connection may cause the KX-T123211 to operate improperly. 
See “During Installation” page 6-1 and “During Connection” page 6-2 before connecting. 
2-8  
						

							To connect Amphenol 57JE type (screw-attach-type 50-pin 
connector) to the KX-T123211, follow the procedure below. 
1. Loosen the three screws to move the metal 
bar aside. 
I Metal bar 
317 
Screws 
2. Pull the Expansion Card (LC#l) 
3. The 50-pin connector (JACK) on the 
Expansion Card has two hook-pins. 
Remove the upper hook-pin, taking 
out the screw. 
/Expansion 
Card 
,50-pin 
connector 4. 
To attach the Amphenol 57JE type 
(PLUG) to the connector, drive the 
accessory Screw at the upper part, 
. 
and fasten the accessory Wire Tie 
around the lower hook-pin and the 
Amphenol 57JE type, as shown. 
50-pin* 
connector 
Hook-.pin 
Accessary 
Wire Tie 
When connecting a connector of the type shown 
below, unscrew the lower hook-pin, too. Then drive 
both accessory Screws. 
I Expansion Card 
5d-pin Aonnector 
5. 
Replace the Expansion Card (LC#l). 
6. 
To connect to the other Expansion Card 
(LC#2), repeat the steps 2 to 5. 
7. 
Replace the bar and tighten the screws. 
2-9  
						

							0 Connection of a Standard Telephone 
Connect the only pin number of “T” and “R”.  Cable Pin Numbers to be connected l Connection of the KX-T123235 (Proprietary 
Telephone) 
T : Tip Dl : Data 1 Pl : 3 Pair Voice 
R : Ring D2 : Data 2 P2 : 3 Pair Voice 
0 Connection of the Proprietary Telephone 
Connect the only pin number of “T”, “R”, 
“Dl ” and 
“ D2”. 
ONN CABLE CLIP 
PIN COLOR 
NO LC-1 
LC-2 
LC-3 LC-4 
26 WHT-BLU 
1 T 
T T T 
1 BLU-WHT 
2 R R 
R 
27 WHT-ORN 
3 
JACK DI R 
JACK ~1 
JACK D1 JACK Dj 
2 ORN-WHT 
4 No.1 D2 
No.9 D2 
No.17 D2 
No.25 D2 28 WHT-GRN 
5 Pl PI Pi Pl 
3 GRN-WHT 
6 P2 P2 P2 P2 
29 WHT-BRN 
7 T T 
T T 
4 BRN-WHT 
8 R R 
R R 
23 GRN-VI0 46 
19 VIO-BRN 
47 
24 BRN-VI0 48 
50 VIO-SLT 49 
25 SLT-VI0 50 
No.8 ;: 
P2 
No.16 ;: 
No.24 E: ,No.32 E; 
P2 P2 P2 
Station wrnng (Y-Parr twtsteu cablrng): 
50 Pi 
Bridging Clips  
						

							If the telephone you are using with the KX-T123211 is polarity sensitive. - 
1. Connect all extension wiring to the KX-T123211. 
2. Confirm that dialing can be done from all the 
extensions using a tone telephone. 
3. If a dialing can not be done, the polarity between 
the extension and the KX-T123211 must be reversed. 6. Confirm that dialing can be done on the 
following extensions using a tone telephone. 
Extension of jack number l--CO1 
Extension of jack number %-CO2 
Extension of jack number g--CO5 
Extension of jack number lo--CO6 
Extension of jack number 17--CO9 
Extension of jack number 18--CO10 
Central Office Line KX-Tl23211 
Extension 
4. Set the Power Switch on the KX-T123211 to the 
OFF position. 7. If dialing can not be done, the polarity between 
the KX-T123211 and the Central Office Line must 
be reversed. 
KX-Tl23211 
Reverse here 
6. If any extension is changed or replaced, repeat 
these procedures (from step 1 through step 7). 
5. Connect all Central Office (CO) Lines. 
. 
2-11  
						

							Serial Printer 
 Make cables so that the printer may be connected 
to the KX-Tl23211 as shown in the chart. 
Serial Interface 
Cables must be shielded and the maximum length 
is 6.5 feet. ( RS-232C ) 
Connection Chart : 
KX-T123211 RS-232C Printer RS-232C When using special accessories such as cable, the 
user should use those specified in this installation 
manual to comply with the limits for a Class A 
computing device pursuant to Subpart J of Part 15 
of FCC Rules.  I 
Circuit 
Signal Pin Pin Signal Circuit 
Type 
(EIA) Name No. No. -Name llg 
FG l-l FG AA 
BA TXD 2 - 3 RXD BB 
BB RXD 3 - 2 TXD BA 
DTR CD The pin configuration of EIA (RS-232C) connector is 
as follows. 
Circuit Type 
EIA 1 CCITT  Pin 
Number Signal Name 
FG 
TXD Frame Ground 
Transmitted 
Data AA 
BA 101 
103 
KX-D491 OD, KX-D4911, KX-D4920, KX-D4985, etc. 
If you connect this unit to a Panasonic Data 
Terminal, the Communication Parameter 
Transmit XON / XOFF on the Data Terminal must 
be set to the “YES” position. 
For further details, see the Operating 
Instructions of the Data Terminal. 
2-12 RXD 
RTS BB 104 
CA 105  Received ,Data 
Request To 
Send 
Clear To Send CB 106 
Data Set Ready cc 107 
l Panasonic data terminal ; 
CTS 
DSR 
AB 
CF 
7 SG 
8 DCC Signal Ground 
Data Carrier 
Detect’ 
Data Terminal 
Ready CD 108.2  20 DTR  
						

							EIA (RS-232C) SIGNALS: 
Frame Ground (FG); 
Connects to the unit frame and the earth ground 
conductor of the AC power cord. 
Transmitted Data (TXD); . . . . . . . . . . . . . . . . ..@Jtpuq 
Conveys signals from the unit to the printer. A 
“Mark” condition is held unless data or BREAK 
signals are being transmitted. 
Received Data (R)(D);. . . . . . . . . . . . . . . . . . . . . . . . .(input) 
Conveys signals from the printer. 
Request To Send (RTS); . . . . . . . . . . . . . . . . . . .((-Jutput) 
. 
This lead is held ON whenever DSR is ON. 
Clear To Send (CTS);..................... **(input) 
An ON condition of circuit CTS indicates that the 
printer is ready to receive data from the unit. The 
unit dose not attempt to transfer data or receive 
data when circuit CTS is OFF. Data Set Ready(DSR);.......................(input) 
An On condition of circuit DSR indicates the 
printer is ready. Circuit DSR ON does not indicate 
that communication has been established with 
the printer. 
Signal Ground (SG); 
Connects to the DC ground of the unit for all 
interface signal. 
Data Terminal Ready (DTR)...............(output) 
This signal line is turned ON by the unit to indicate 
that it is ON LINE. Circuit DTR ON does not 
indicate that communication has been 
established with the printer. It is switched OFF 
when the unit is OFF LINE. 
Data Carrier Detect (DCD)..................(input) 
The ON condition is an indication to data terminal 
(DTE) that the carrier signal is being received. 
i 
1. If the Panasonic printer which is used has a (KX-PI 1 D or KX-P17) board and is connected to the 
KX-T123211 , set the communication parameters below. 
KX-Pl 
1 D 
KX-P17 
KX-T123211 
DIP switch 
Setting DIP switch 
Seth ng 
Word length 
7 bit (default) SWl-1 ON SWl-4 ON 
Program to “EVEN” SWl-2 
Parity ON SWl-5 
OFF 
(See page 3-32) SWl-3 
ON SWl-6 
OFF 
SWl-5 
ON 
SWl-1 
Baud Rate 12008 (default) SWl-6 
OFF OFF 
SWl-7 
OFF SWl-2 
OFF 
SWl-8 
OFF SWl-3 
ON 
Protocol XON / XOFF mode 
only SW2-8 
OFF 
SWl-8 ON 
2. If the Panasonic data terminal is a KX-D4985 or KX-D4920 and is connected to the KX-T123211, the default value 
of communication parameter is the same a.s that of the KX-T123211. 
If the KX-D491 OD is connected to the KX-T123211, set the baud rate of the KX-D491 OD to 1200 baud, the other 
default value is the same as that of the KX-Tl23211. 
2-l 3  
						

							Speaker l Output impedance: 
/ 
 6OOfl 
0 
CL 
Amplifier 
Useshielded cable. 
0 
0 
Use an RCA connector. Paging jack 1 
Speaker 
/ 
 
0 Paging equipment 1 
Amplifier 
Paging equipment 2 
External Music Source 
Adjust the sound level 
of the music on hold 
with the Volume 
control. Use a two- 
conductor plug 
(9/64 inch in diameter) 
l Input impedance 
0 Input Level 
-1OdBm 
1 1. EXT MUSIC Jack 
2-14