Nortel Modular Ics 6.0 Installer Guide

							Private networking using PRI SL-1 / 151
P0992638 03Modular ICS 6. 0 Installer Guide
Assigning PNIs for adjacent nodes
1. After you enter your password, press ‘ until the 
prompt displays Hardware: 
2. Press ≠. The prompt displays Show module.
3. Enter the module where the PRI card you have configured 
for SL-1 resides.
4. Press ≠. The prompt displays CdX-KSU.
5. Press ≠. The prompt displays Card type.
6. Press ‘. The prompt displays Lines.
7. Enter the line number you want to configure.
8. Press ≠. The prompt displays Protocol.
9. Ensure that this displays SL-1.
10. Press ‘. The prompt displays PrivNetID:.
11. Enter the PNI of the adjacent node.
12. Repeat these steps for all the modes that are directly 
adjacent to your system.
Local system
To set up the local system, you need to assign a target line to 
the DN for the voice mail system, then enter that DN into the 
target line record.
1. After you enter your password, at the Terminals&Sets 
prompt, press ≠.
The prompt displays: Show set: 
2. Enter the DN number for the Auto Attendant.
3. Press ≠. The prompt displays Line access. 
						

							152 / Private networking using PRI SL-1
Modular ICS 6.0 Installer GuideP0992638 03
4. Press ≠. The prompt displays Line assignment.
5. Enter the target line number for the Auto Attendant 
system.
6. Press CHANGE
 to change the setting for each line to one of 
the following: Unassigned, Ring only, Appr&Ring, and 
Appr only. 
7. Press – until you reach the top level, then press 
‘. The prompt displays Lines.
8. Press ≠. The prompt displays Show line.
9. Enter the target line number you entered in step 5.
10. Press ≠. The prompt displays. The prompt displays 
Line Type.
11. Press ‘. The prompt displays Rec'd #.
12. Enter the DN for the Auto Attendant system.
13. Exit programming.
Remote system
On the nodes that are not directly connected to the central Auto 
Attendant system, you need to use the Telco Features headings 
to identify the route to the system.
1. After you enter your password, press ‘ until the 
prompt displays Telco Features: 
2. Press ≠. The prompt displays VMsg Center 
tel#s.
3. Press ≠. The prompt displays VMsg Center 1.
4. Press ≠. The prompt displays Use:.
5. Press CHANGE
 to until you reach Routing tbl.  
						

							Private networking using PRI SL-1 / 153
P0992638 03Modular ICS 6. 0 Installer Guide
6. Press ‘. The prompt displays Tel #:.
7. Enter the number to access the external Auto Attendant 
system.
Set Telco features for the CAA DN
1. Press – until you reach the top level, then press 
‘ until the prompt displays Terminals&Sets.
2. Press ≠. The prompt displays: Show set: 
3. Enter the DN for the Auto Attendant system.
4. Press ≠. The prompt displays Line access.
5. Press ‘ until the prompt displays Telco 
features.
6. Press ≠. The prompt displays Feature Assign.
7. Press ≠. The prompt displays Show line.
8. Enter the line number that connects to the system for the 
central voice mail system.
9. Press ≠. The prompt displays Caller ID Set.
10. Press ‘ until the prompt displays Extl VMsg 
set.
11. Press CHANGE
 to select Y (yes). 
Set Telco features for the target line
1. Press – until you reach the top level, then press 
‘ until the prompt displays Lines.
2. Press ≠. The prompt displays: Show line: 
3. Enter the target line number for the voice mail system.
4. Press ≠. The prompt displays: Trunk/line 
data:  
						

							154 / Private networking using PRI SL-1
Modular ICS 6.0 Installer GuideP0992638 03
5. Press ‘ until the prompt displays Telco 
features.
6. Press ≠. The prompt displays VMsg Center 1.
7. Press ≠. The prompt displays Use:.
8. Press CHANGE
 to until you reach Routing tbl. 
9. Press ‘. The prompt displays Tel #:.
10. Enter the number to access the external Auto Attendant 
system.
11. Exit programming.
Voice mail configuration
On the voice mail system, set the following parameters:
Set Redirected DN to Yes.
Under the F983 AA promopt, set ANS: Y for the voice 
main DN assigned target line.
Under F983 dial 77 and set External init as Y.
From the CVM/CAA lines, use the default greeting table 1.
For detailed directions, refer to the addendum titled: Installing 
Norstar Voice Mail as a Centralized Voice Mail System. 
						

							Customer Use / 155
P0992638 03Modular ICS 6. 0 Installer Guide
Customer Use
This section shows sample configurations for different types 
of network access. Each example has four parts:
A scenario explains the goal of the call and what is 
required to achieve it.
A diagram shows the network configuration that supports 
the application.
A list shows the Norstar hardware required to support the 
configuration.
Tables show the programming. Only those settings that are 
important to network access are described.
Public network
The calls described in this section all originate from the public 
network. Callers dial in using a p ublic DN into the system.
Call one or more Norstar telephones
Ms. Nelson is a bank customer with a question for an 
accountant. She dials the number that maps onto target line 
203. All of the telephones ring in the accounting department.
Ta r g e t  l i n e
203
Ms. Nelson
DIDAccountant
(225)
Accountant
(226)
Central OfficeDID trunk 
cartridges 
						

							156 / Customer Use
Modular ICS 6.0 Installer GuideP0992638 03
Hardware: ICS, a Trunk Module with a DID Trunk Cartridge, 
or a DTI with lines programmed as DID. 
Call Norstar and select tie lines to a private network
A manager in Georgia wants to use the tie lines at headquarters 
to call Washington. He dials a telephone number that maps 
onto the DISA DN, enters a Class of Service (COS) password, 
then dials a line pool access code to select a tie line to 
Washington. 
Using tie lines
Hardware: ICS, a Trunk Module with a DID Trunk Cartridge, 
two E&M/DISA Trunk Cartridges for the three trunks in the 
line pool to Washington, or a DTI with one DID line and three 
E&M lines. 
HeadingParameterSetting 
Trk/Line DataRecd #
Line 0514321 (for Line 203)
DID
Recd # lengthRecd # lengthfour digits (can be from three to 
seven digits, but must match 
number of digits sent by central 
office)
HeadingParameterSetting 
Incoming trunk:
Trk/Line Data
Line 049DID
Access codesDISA DN5321
 
Manager
(in Georgia)
Central Office NorstarDIDDID and E&M/DISA 
trunk cartridges
E&M line pool 
to Washington 
						

							Customer Use / 157
P0992638 03Modular ICS 6. 0 Installer Guide
Call Norstar and select lines to the public network
Gord wants to make a long-distance business call from home. 
To avoid being charged, he dials the telephone number that 
maps onto the Auto DN at work. After hearing the dial tone, 
Gord dials a line pool access code to select a line to the public 
network. He then dials the long-distance number. 
Using DID to dial long-distance
Recd # lengthRecd # lengthfour digits (three to seven digits, 
but must match number of digits 
sent by central office)
Outgoing trunk:
Trk/Line Data
Line 053
Line typeE&M
Pool F
Access codesLine pool F6 (up to four digits) 
COS pswdsDefine restrictions. Define remote 
access pkgs. Assign a restriction 
filter to the line. Assign COS 
passwords and filters for each 
Class of Service.
HeadingParameterSetting 
 
Gord at home Business client
Central Office Central OfficeNorstar
DID
line pool 
						

							158 / Customer Use
Modular ICS 6.0 Installer GuideP0992638 03
Hardware: ICS, a Trunk Module with a DID Trunk Cartridge 
or DTI with several DID lines. 
HeadingParameterSetting 
Incoming trunk:
Trk/Line Data
Line 049DID
Access codes Auto DN4321
Recd # lengthRecd # lengthfour digits 
(can be from three to seven 
digits, but must match number of 
digits sent by central office)
Lines /Restrictions 
and Remote 
accessDefine restriction filters. Define 
remote access packages. Assign 
a remote restriction and remote 
package to the line.
Outgoing trunk:
Trk/Line Data
Line 001
Line type Loop
Pool A
Access codesLine pool A1234
Lines /RestrictionsAssign a restriction filter to the 
line. 
						

							Customer Use / 159
P0992638 03Modular ICS 6. 0 Installer Guide
Private network
All the calls described in this section originate from within the 
networked system.
Call one or more Norstar telephones
The production supervisor in Houston selects the less-
expensive company Tie line to call the manager at the 
Administration office in Dallas. Once the line is selected, the 
production supervisor dials the digits that will map onto the 
target line of the manager in Dallas.
Calling from a Norstar to a remote PBX
Hardware: ICS, a Trunk Module with an E&M/DISA Trunk 
Cartridge or a DTI with an E&M line. 
HeadingParameterSetting 
Incoming trunk:
Trk/Line Data
Recd #
Line 049
Ans Mode4321(for target line 243)
E&M
Auto
Recd # lengthRecd # lengthfour digits (can be from three to 
seven digits, but  must match number 
sent by central office)
 
PBX in 
HoustonManager 
in Dallas
Norstar E&M
target line
243 
						

							160 / Customer Use
Modular ICS 6.0 Installer GuideP0992638 03
Use tie lines to other nodes in the private network
At a branch office, Joan selects a tie line to the main office. 
After hearing the dial tone, she dials a line pool access code to 
select another tie line to a branch office in the next state.
Calling within the network through Tie lines
Hardware: ICS, a Trunk Module with two E&M/DISA Trunk 
Cartridges, for the three lines in the line pool and the one 
incoming line, or a DTI with four E&M lines.
HeadingParameterSetting 
Incoming trunk:
Trk/Line Data
Line 049
Ans modeE&M
Auto
Under Lines /
Restrictions /
Remote accessDefine restriction filters. Define remote 
access packages. Assign a remote 
restriction  and remote package to the 
trunk.
Outgoing trunk:
Trk/Line Data
Line 050
Line typeE&M
Pool D
Access codesLine pool D71 (can be from one to four digits)
Lines /
RestrictionsAssign a restriction filter to the trunk.
 
Joan at 
branch office
key system
Norstar E&ME&M line pool
to next state