NEC Neax 2400 Imx Wireless System Manual

							CHAPTER 5 ND-70290 (E)
Pag e 2 94
Revision 3.0
AZARL
AZARL  : Assignment of ZT Area Information for Local Data Memory
1. GENERAL
This command is used to assign and delete the Zone Transceiver Area information in the Local Node (LN).
2. PRECAUTIONS
1. This command is used for the Local Node.
2. All PSs data must be re-download, if control carrier data is changed via this command.
3. The parameters, WTZNSL, WTZNKL, RCHOOL, RCHOSL, RCHFE, CCHGFE, should not be changed
from default setting.
4. ZT must be restarted after using this command.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ZSL (ZONE SELECT LEVEL) : 0-255
ZKL (ZONE KEEP LEVEL) : 0-255
HOL (HAND-OVER OPERATION LEVEL) : 0-255
HSL (HAND-OVER SELECT LEVEL) : 0-255
HFT (HAND-OVER FER THRESHOLD) : 0-255
CCFT (CHANNEL CHANGE FER THRESHOLD) : 0-255
NCCR (NUMBER OF CONTROL CARRIER) : 0-5
CCR 1-5 (CONTROL CARRIER 1-5) : 0-20
If this is not assigned, the default setting is below.
ZSL = 67 (33dB µ V)
ZKL = 56 (22dB µ V)
HOL = 59 (25dB µ V)
HSL = 67 (33dB µ V)
HFT = 10 frame error/240 frame (1.2 sec)
(This is effective for mode2 ZT.)
CCFT = 24 frame error/240 frame (1.2 sec)
NCCR = 3
CCR 1 = 2 Channel
CCR 2 = 4 Channel
CCR 3 = 6 Channel
CCR 4 = 0 None
CCR 5 = 0 None 
						

							ND-70290 (E) CHAPTER 5
Page 295
Revision 3.0
AZARN
AZARN  : Assignment of ZT Area Information for Network Data Memory
1. GENERAL
This command is used to assign and delete the Zone Transceiver Area information in the Network Control Node
(NCN).
2. PRECAUTIONS
1. This command is used for the Network Control Node.
2. All PSs data must be re-download, if control carrier data is changed via this command.
3. The parameters, WTZNSL, WTZNKL, RCHOOL, RCHOSL, RCHFE, CCHGFE, should not be changed
from default setting.
4. ZT must be restarted after using this command.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ZSL (ZONE SELECT LEVEL) : 0-255
ZKL (ZONE KEEP LEVEL) : 0-255
HOL (HAND-OVER OPERATION LEVEL) : 0-255
HSL (HAND-OVER SELECT LEVEL) : 0-255
HFT (HAND-OVER FER THRESHOLD) : 0-255
CCFT (CHANNEL CHANGE FER THRESHOLD) : 0-255
NCCR (NUMBER OF CONTROL CARRIER) : 0-5
CCR 1-5 (CONTROL CARRIER 1-5) : 0-20
If this data is not assigned, the default setting is below.
ZSL = 67 (33dB µ V)
ZKL = 56 (22dB µ V)
HOL = 59 (25dB µ V)
HSL = 67 (33dB µ V)
HFT = 10 frame error/240 frame (1.2 sec)
(This is effective for mode 2 ZT.)
CCFT = 24 frame error/240 frame (1.2 sec)
NCCR = 3
CCR 1 = 2 Channel
CCR 2 = 4 Channel
CCR 3 = 6 Channel
CCR 4 = 0 None
CCR 5 = 0 None 
						

							CHAPTER 5 ND-70290 (E)
Pag e 2 96
Revision 3.0
COCS1L
COCS1L  : Control of CS/ZT Status Read for Local Data Memory
1. GENERAL
This command is used to read the status of the CS/ZT in the Local Node (LN).
2. PRECAUTIONS
This command is used for the Local Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
After the assignment data is processed between PBX and MAT; following parameter is automatically
assigned
LENS (EQUIPMENT NUMBER) : Line Equipment Number
TN (TENANT NUMBER) : 1-6
CS-ID (CS/ZT-IDENTIFY) : CS/ZT-Identify
MAIN (MAIN CONDITION OF CS/ZT : Main Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
SUB (CONTROL CONDITION OF CS/ZT : Control Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
CS/ZT TYPE (CS TYPE) : Control (Control CS/ZT)
General (Control CS/ZT)
CS STATUS (CS/ZT STATUS) : CS/ZT status (If parameter can be changed)
NON-OP (Non Open)
CLOSE (Close)
OPERATE (Operating Now)
LINK STATUS (DATA LINK STATUS) : Data Link Status (If parameter can be changed)
UNLINK (Data Link Break)
OPEN (Data Link Open)
CLOSE (CS/ZT Fault After Return)
FAULT (CS/ZT Fault)
BCH B2 (B2CH STATUS) : B2ch Status (If parameter can be changed)
IDLE (B2ch Idle)
BUSY (B2ch Busy)
CLOSE (B2ch Close)
BCH B3 (B4CH STATUS) : B3ch Status (If parameter can be changed)
IDLE (B3ch Idle)
BUSY (B3ch Busy)
CLOSE (B3ch Close)
BCH B4 (B4CH STATUS) : B4ch Status (If parameter can be changed)
IDLE (B4ch Idle)
BUSY (B4ch Busy)
CLOSE (B4ch Close)
FLT (NG CAUSE) : 0-FF (Only Display)
Only
Display 
						

							ND-70290 (E) CHAPTER 5
Page 297
Revision 3.0
COCS1N
COCS1N  : Control of CS/ZT Status Read for Network Data Memory
1. GENERAL
This command is used to read the status of the CS/ZT status read in the Network Control Node (NCN).
2. PRECAUTIONS
This command is used for the Network Control Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
After the assignment data is processed between PBX and MAT; following parameter is automatically
assigned
LENS (EQUIPMENT NUMBER) : Line Equipment Number
TN (TENANT NUMBER) : 1-6
CS-ID (CS/ZT-IDENTIFY) : CS/ZT-Identify
MAIN (MAIN CONDITION OF CS/ZT : Main Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
SUB (CONTROL CONDITION OF CS/ZT : Control Condition of CS/ZT Management
MANAGEMENT FOR DEVICE SIDE) For Device Side
CS/ZT TYPE (CS TYPE) : Control (Control CS/ZT)
General (Control CS/ZT)
CS STATUS (CS/ZT STATUS) : CS/ZT status (If parameter can be changed)
NON-OP (Non Open)
CLOSE (Close)
OPERATE (Operating Now)
LINK STATUS (DATA LINK STATUS) : Data Link Status (If parameter can be changed)
UNLINK (Data Link Break)
OPEN (Data Link Open)
CLOSE (CS/ZT Fault After Return)
FAULT (CS/ZT Fault)
BCH B2 (B2CH STATUS) : B2ch Status (If parameter can be changed)
IDLE (B2ch Idle)
BUSY (B2ch Busy)
CLOSE (B2ch Close)
BCH B3 (B4CH STATUS) : B3ch Status (If parameter can be changed)
IDLE (B3ch Idle)
BUSY (B3ch Busy)
CLOSE (B3ch Close)
BCH B4 (B4CH STATUS) : B4ch Status (If parameter can be changed)
IDLE (B4ch Idle)
BUSY (B4ch Busy)
CLOSE (B4ch Close)
FLT (NG CAUSE) : 0-FF (Only Display)
Only
Display 
						

							CHAPTER 5 ND-70290 (E)
Pag e 2 98
Revision 3.0
COCS2L
COCS2L  : Change of CS/ZT Operation Parameter for Local Data Memory
1. GENERAL
This command is used to change the CS/ZT operation parameter in the Local Node (LN).
2. PRECAUTIONS
This command is used for the Local Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
MODE (GLOBAL DEFINITION : 1: NOR (Normal)
INFORMATION PATTERN NUMBER) 2: HBY (Heavy)
ZONE (ZONE KIND) : 1: LG (Large)
2: SM (Small)
PAS (POSITION ASSIGNMENT) : 1: SET
2: CANCEL 
						

							ND-70290 (E) CHAPTER 5
Page 299
Revision 3.0
COCS2N
COCS2N  : Change of CS/ZT Operation Parameter for Network Data Memory
1. GENERAL
This command is used to change the CS/ZT operation parameter in the Network Control Node (NCN).
2. PRECAUTIONS
This command is used for the Network Data Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
MODE (GLOBAL DEFINITION : 1: NOR (Normal)
INFORMATION PATTERN NUMBER) 2: HBY (Heavy)
ZONE (ZONE KIND) : 1: LG (Large)
2: SM (Small)
PAS (POSITION ASSIGNMENT) : 1: SET
2: CANCEL 
						

							CHAPTER 5 ND-70290 (E)
Pag e 3 00
Revision 3.0
COCS3L
COCS3L  : Change of CS/ZT Reset for Local Data Memory
1. GENERAL
This command is used to control CS/ZT Reset for the Local Node (LN).
2. PRECAUTIONS
This command is used for the Local Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
  After the assignment data is processed between PBX and MAT; following parameter is automatically
assigned
TN (TENANT NUMBER) : 1-System Max.
LENS (EQUIPMENT NUMBER) : LENS EQUIPMENT NUMBER
FLT (NG CAUSE) : 0-FF (Only Display) 
						

							ND-70290 (E) CHAPTER 5
Page 301
Revision 3.0
COCS3N
COCS3N  : Control of CS/ZT Reset for Network Data Memory
1. GENERAL
This command is used to control CS/ZT Reset for the Local Node (LN).
2. PRECAUTIONS
This command is used for the Network Control Node.
3. DATA ENTRY INSTRUCTIONS
PCN (PHS COMMUNITY NUMBER) : 1-1024
ERN (CALLING AREA NUMBER) : 1-32
GRN (GROUP NUMBER) : 1-8
CSN (CS/ZT NUMBER) : 1-32
 After the assignment data is processed between PBX and MAT; following parameters are automatically
assigned
TN (TENANT NUMBER) : 1-System Max.
LENS (EQUIPMENT NUMBER) : LENS EQUIPMENT NUMBER
FLT (NG CAUSE) : 0-FF (Only Display) 
						

							CHAPTER 5 ND-70290 (E)
Pag e 3 02
Revision 3.0
DLIN
DLIN  : Display of a List of Roaming PS
1. GENERAL
This command is used to display/delete a list of data related to the Roaming PS that is available on the Home
Location Register (HLR) or Visitor Location Register (VLR).
2. PRECAUTIONS
None
3. DATA ENTRY INSTRUCTION
FUNK (FUNCTION NUMBER) : 1 = PS – Moving to another PBX (HLR Display)
2 = PS – Moving from another PBX (VLR Display)
CNT (DELETION NUMBER) : Used to delete the currently Roaming PS data, displayed below.
Display Data
UGN (USER GROUP NUMBER) :  Displayed when “FUNK = 1” is assigned.
TELN (TELEPHONE NUMBER) :  Max. 16 digits
Displayed when “FUNK = 1” is assigned.
RTN (ROUTE NUMBER) :  Max. 24 digits
Displayed when “FUNK = 1” is assigned.
VPSCN (VISITOR PS CALLING NUMBER) :  Max. 24 digits
Displayed when “FUNK = 2” is assigned.
PSN (PS NUMBER) :  Displayed when “FUNK = 2” is assigned. 
						

							ND-70290 (E) CHAPTER 5
Page 303
Revision 3.0
DPSN
DPSN  : Display of PS Station Data
1. GENERAL
This command is used to display the PS station data. The display appears when the Tenant Number and Physical
Station/Telephone Number are entered. This command can also be used to display information on Hot Line
station, details on PS data, Call Pickup Group data, Station Hunting data and Uniform Call Distribution (UCD)
data.
2. PRECAUTIONS
Station Hunting data and Uniform Call Distribution (UCD) data are displayed when using Series 7400 Release
8 or later software.
3. PARAMETERS
a. Parameters on PS Station Number
TN/UGN: Tenant Number/User Group Number
STN/PS TELN: Station Number/PS Telephone Number
ETN: Effective Tenant Number
LENS: Equipment Number
TEC: Telephone Equipment Class
RSC: Route Restriction Class
SFC: Service Feature Class
b. Parameters on Related Data
PH: Phantom Kind
0: PHSTN Data is ALL 0. (PHSTN is Not Registered)
1: PHSTN Data is Individual Phantom Number.
2: PHSTN Data is Group Phantom Number.
PHSTN 0-4: Phantom Station Number
CPGF: Call Pickup Flag
0: Not Belong in Call Pickup Group
1 or 2: Belong in Call Pickup Group
HTI: Hot Line Index
0: Hot Line Data is Nothing
1: Connection for Station
HOT CON TN: Hot Line Connective Tenant Number
HOT CON STN: Hot Line Connective Station Number
2: Connection for External Line
HOT ADC: Hot Line Connective Speed Calling Abbreviated Digit
4: Connection for Trunk
HOT CON RT: Hot Line Connective Route Number
HOT CON TK: Hot Line Connective Trunk Number
PS-ID: PS-ID
IND-PS: Individual PS Number
PS STN: PS Station Number
PSNO. TYPE: PS Number Type