NEC Neax 2400 Imx Wireless System Manual

							CHAPTER 4 ND-70290 (E)
Pag e 1 04
Revision 3.0
OFFICE DATA ASSIGNMENT
3. ZT Deletion Procedure
1) MBCSN ( MAKE BUSY CS/ZT for Network Data Memory)
2) ACSDN (Assignment of CS/ZT Data for Network Data Memory)
Delete the ZT Data.
 START
 END 
						

							ND-70290 (E) CHAPTER 4
Page 105
Revision 3.0
OFFICE DATA ASSIGNMENT
2.3 PS OFFICE DATA ASSIGNMENT
Below are explanations about assigning office data to place the PS in operation in the Built-in PCS system.
1. Initial Start-UP of the PS
2. Addition of the PS
1) AFMU
Note:When a PS is assigned by APSD command, logically it occupies a port from module group
(MG) 31 to 26, from larger number of MG to smaller. Using AFMU command, those MGs must
be assigned for Fusion Network.
Since One MG can contain up to 768 PSs in it, for instance. If you need maximum of 4000 PSs
in a node, MG31, 30, 29, 28, 27 and 26 must be assigned.
At the beginning of installation, you do not have to allocate all six MGs in a node, just the
aamount needed at the time. Later, when you need to add more PSs to the node, you can come
back to AFMU again. ALGSN command will tell you when it’s time by giving you an error in
assigning telephone number to a MG which has not been assigned yet.
2) APSD (Assignment of the PS Operation Data for DM)
This command assigns the PS operation data including its tenant No., station No., Service Feature 
Restriction Class (SFC) and the Route Restriction Class (RSC) in consideration of the numbering 
plan/restriction data.
 TN : Tenant
 PS STN : PS Station Number
 KIND : PS KIND :6 (My Line) or 7 (Sub Line)
 RSC : Route Restriction Class
 SFC : Service Feature Restriction Class
 PS-ID : Max. 9 [DEC]
 PSNO : PS KIND : 2 (13 digits or less [BCD]) fixed
  NO. : Assign the same number as the PS NO. according to PS KIND.
 NWN : Network Number   : Only for Roaming Feature
 ADERA : Additional Area Number  : Only for Roaming Feature
 CTRN : Country Number   : 794 (USA) fixed
 Sub-Sysid : Number of Sub-Sysid   : Not used
3) ALGSN (Assignment of Telephone Number Data for Network Data Memory)
Refer to “Office Data Specification Manual”.
4) APDLN (Down loads of PS Operation Data)
This command loads the PS operation data to the PS.
 UGN
 PS Telephone Number : Max. 16 Digits
TYPE=2
 PS No. : Max. 13 Digits
Note:If CBCN has never been done in Fusion Network after the last initialization, please do CBCN
before ALGNN.
 END
 START 
						

							CHAPTER 4 ND-70290 (E)
Pag e 1 06
Revision 3.0
OFFICE DATA ASSIGNMENT
3. Deletion of the PS data
1) ALGSN (Assignment of Telephone Number Data for Network Data Memory)
Delete the Telephone Number and LENS related.
2) APSD (Assignment of the PS Operation Data for DM)
Using this command, delete the PS data to be cleared such as tenant No., station No., SFC and 
RSC.
Note:If CBCN has never been done in Fusion Network after the last initialization, please do CBCN
before ALGSN.
 END
 START 
						

							ND-70290 (E) CHAPTER 4
Page 107
Revision 3.0
OFFICE DATA ASSIGNMENT
3. ASSIGNMENT OF SERVICE FEATURE DATA
This section describes how to assign the data for the following service features.
 Automatic Announcement-PS Out of Zone/C.F.-PS Incoming Incomplete
 Automatic Announcement-Disconnected PS Out of Zone
 Name Display
 Name Display-CCIS
 Number Sharing
PCS Roaming
 TTC Q. 931a protocol Tie Line with PCS Roaming
 Two-Line Operation
 Voice Mail Indication (VMI)
 ZT Program Download
 Call Forwarding-Dropped Calls
 Data Communications-32 kbps
 Authorization Code
Call Park
 Group Call-Automatic Conference (20-party)
 Short Text Message Service 
						

							CHAPTER 4 ND-70290 (E)
Pag e 1 08
Revision 3.0
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
1. GENERAL DESCRIPTION
When a call cannot terminate to a PS which is Out of Zone or whose power is OFF, the system automatically
answers the call and provides an announcement to notify the calling party that the called PS is Out  of Zone or
if the C.F.-PS Incoming Incomplete is set to a given destination, the aborted call can be transferred to the
preprogrammed station or PS.
2. OPERATING PROCEDURE
No manual operation.
3. SERVICE CONDITIONS
1. C.F.-PS Incoming Incomplete can be programmed and cancelled with the PS by pressing Access
Code+transferred station number. 
Note 1
2. When the PS is Out of Zone or its power is OFF, and the call is an incoming call directly via the Attendant
Console, the caller does not hear the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE, but hears the
following tones.
 DIT: RBT is heard
 REMOTE ACCESS TO SYSTEM: BT is heard
 AUTOMATED ATTENDANT: BT is heard
 ATTENDANT CONSOLE : BT is heard
 ISDN-DID ADDRESSING: Announcement of ISDN (PSTN) is heard.
3. One system is given one kind of recorded message for the AUTOMATIC ANNOUNCEMENT-PS OUT OF
ZONE.
4. On the condition that both the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE and C.F.-PS
INCOMING INCOMPLETE are assigned to a PS, priority is given to the C.F.-PS INCOMING
INCOMPLETE.
5. If an incoming call terminated at the very moment when a PS user is setting the C.F.-PS INCOMING
INCOMPLETE with a Pre-Set Dialing (before OFF-HOOK), the procedure becomes invalid.
6. If another transfer service is set to the target destination party of the C.F.-PS INCOMING INCOMPLETE,
the call is transferred to the last end party.
7. When a call is transferred to another PS activated by the C.F.-PS INCOMING INCOMPLETE and when the
call termination is not completed, the call can be transferred to another destination party if the C.F.-PS
INCOMING INCOMPLETE is set. If the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE is
assigned, the caller hears the announcement. When both the C.F.-PS INCOMING INCOMPLETE and the
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE are not programmed, the caller hears the BT.
8. When the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE is activated but all the announcement
trunks are busy (single connection: AAED M=0), the calling party encounters BT.
9. AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE does not allow the incoming call from outside to
be connected to announcement trunk. The calling party hears RBT. 
						

							ND-70290 (E) CHAPTER 4
Page 109
Revision 3.0
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
10. The incoming incomplete call to PS can be transferred to other PSs, stations, Attendant Consoles, Central
Office and TIE lines when the C.F.-INCOMING INCOMPLETE is in service.
11. The timer value of incoming incomplete call is approximately 8 seconds, time duration until the system
recognizes that the PS is Out of Zone from an incoming call attempt to the PS.
Priority is given to the C.F.-INCOMING INCOMPLETE over the C.F.-DON’T ANSWER.
12. C.F.-PS INCOMING INCOMPLETE is not activated in the case of the incoming call from ISDN and the
incoming call via the Attendant Console. The caller encounters the AUTOMATIC ANNOUNCEMENT-PS
OUT OF ZONE or BT.
13. When a forwarded station for the C.F.-PS INCOMING INCOMPLETE sets the CALL FORWARDING-
ALL CALLS to the announcement, the C.F.-PS INCOMING INCOMPLETE is not activated, instead the
caller hears BT.
14. In the Fusion Network, every node must have one or more Announcement Trunk.
15. When incoming call comes from ISDN Network, and the timer (T310) of the Network side is expired, the
caller hears the Announcement from Network side.
Note 1:C.F.-PS INCOMING INCOMPLETE is cancelled by system initialization. 
						

							CHAPTER 4 ND-70290 (E)
Pag e 1 10
Revision 3.0
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
4. PROGRAMMING
4-1 Automatic Announcement-PS Out of Zone
 Entry Procedure
1) ARTD (Route Class Data)
Assign the Route Class Data for announcement trunk.
RT : Route Number
OSGS (CDN: 1) = 2
ONSG (CDN: 2) = 2
TF (CDN: 5) = 1
TCL (CDN: 6) = 4
L/T (CDN: 7) = 1
ANS (CDN28) = 1
Assign “0” for other parameters.
2) ALRTN (Assignment of Logical RT for Network Data Memory)
LGRT : Logical Route Number
FPC : Fusion Point Code
RT : Route Number
Note:Not Necessary in the standalone situation.
3) ATRK (Trunk Data)
Assign the data for the announcement trunk.
RT : Route Number
TK : Trunk Number
LENS : Line Equipment Numbers (6 digits)
TN : Tenant Number
4) MBTK (Make Busy of Trunk)
Set the announcement trunk in a make-busy cancel state.
5) ARSC (Route Restriction Class Data)
Assign a Route Restriction Class (RSC) to the station which allows access to the announcement 
route.
D/N : Day/Night Mode
TN : Tenant Number
RT : Route Number
RSC : Route Restriction Class (0-15)
RRI :  Route Restriction Index (0-3)
RES = 1 (Allowed)
A
 START 
						

							ND-70290 (E) CHAPTER 4
Page 111
Revision 3.0
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
5) ARRC (Alternative Route Restriction Pattern Data)
Allow the restriction between the external trunk and the announcement trunk.
ICRT : Incoming Route Number
OGRT : Outgoing Route Number (Announcement trunk)
ARI : D (Direct)
RES = 1 (Allowed)
6) AAED (Announcement Equipment Data)
Assign EQP=60 for the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE
TN : Tenant Number
EQP = 60 (AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE)
C : Duration of Connection
R : Sending RBT
A : 1 (Answer Signal Sending)
M : 1 (Multiple Connection)
 END
A 
						

							CHAPTER 4 ND-70290 (E)
Pag e 1 12
Revision 3.0
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
4-2 C.F.-PS Incoming Incomplete
 Entry Procedures
1) ASYD (Assignment for System Data)
Assign whether to use a same access code for Call Forwarding-Busy Line, Call Forwarding-Don’t 
Answer and C.F.-PS Incoming Incomplete, or use separate access codes.
SYS1, INDEX5, bit 0
0=Same
1=Separate
2) ANPD (Numbering Plan Data)
Assign the necessary number of digits needed to determine the service which is required according 
to the first digit received.
3) ASPA (Special Access Code Data)
Assign the Special Access Code for the C.F.-PS INCOMING INCOMPLETE
CI=N SRV=SSCA SIDA=101 (C.F.-PS INCOMING INCOMPLETE: Set)
CI=N SRV=SSCA SIDA=102 (C.F.-PS INCOMING INCOMPLETE: Cancel)
4) ASFC (Service Feature Class Data)
Allow the C.F.-PS INCOMING INCOMPLETE according to PS Service Feature Class.
SFI=147 (C.F.-INCOMING INCOMPLETE)
RES=1 (Allowed)
 END
 START 
						

							ND-70290 (E) CHAPTER 4
Page 113
Revision 3.0
AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE
AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE
1. GENERAL DESCRIPTION
When a PS user moves Out of Zone (out of the PCS service area) and the call is disconnected, the counterpart
hears the announcement stating the call was disconnected due to the the wireless user going Out of Zone.
2. OPERATING PROCEDURE
No manual operation
3. SERVICE CONDITIONS
1. This service is valid only in a two-party call.
This service cannot be used when a call is placed on hold or conference calling participated in by three-party
or more is in progress.
2.  Digital Announcement Trunk (DAT) circuit card can be used as an announcement trunk.
3. PS user encounters BT when the announcement trunk, when used as single connection (M=0 in the
command AAED) and all the trunks are used.
4. AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE is not applied to the cases
where calls are in progress via a COT line or Attendant Console. A C.O. line subscriber hears ROT and a
caller via the Attendant Console encounters BT.
5. In the Fusion Network, every node must have one or more announcement trunks.