NEC Neax 2400 Imx Wireless System Manual

							CHAPTER 4 ND-70290 (E)
Pag e 1 84
Revision 3.0
GROUP CALL-AUTOMATIC CONFERENCE (20-PARTY)
 Cancel Procedure
When deleting the ASDT/ALGSL/APHNL command data assigned as conferee, the user must first,
delete the AHLGL data.10) ASHCN (Assignment of Station Hunting Group-Circular for NDM)
Assign Station Hunting Group-Circular between conference leader ports and/or conference 
leader ports for cascade connection on each set of CFTB circuit cards.
Note 11:This command is required, only when calling a conference discovering a set of CFTB
circuit cards which is in an idle state from multiple CFTB circuit cards.
B
END 
						

							ND-70290 (E) CHAPTER 4
Page 185
Revision 3.0
SHORT TEXT MESSAGE SERVICE
SHORT TEXT MESSAGE SERVICE
1. GENERAL Description
This feature enables a short text message (STM), once arrived at a mail box of the Short Text Message Server
(external equipment), to be automatically distributed to the addressee PS via Open Application Interface (OAI).
This feature also provides a Zip Tone and “TM WAITING” notification on the display (LCD) of the addressee
PS that is busy, and if the PS is out of zone, even makes retransmission  of the STM after the PS returns to the
zone. See Figure 4-8 for details:
Note:This describes STM Facilities available for external STM OAI application. Actual functionalities all depend
on the application. Please refer to the OAI application manuals.
Figure 4-8  Outline of Shor t Text Message (STM) Service
           ZT
PBX        ST M Server 
(Exter nal Equipment)   PS 
(Busy)
Ta l k i n g
➁ Notification
Note:  Notification : Zip Tone and indication on PS display (TM WAITING).Note
OAI
           ZT
PBX        ST M Server 
(Exter nal Equipment) PS
STMOAI    Mail 
Arrived !Mail 
➀STM
   Mail 
Arrived !Mail
DtermPS or
 After PS Release
PS
Out of Zone           ZT
PBX        ST M Server 
(Exter nal Equipment)
OAI
➀ ST M
   Mail 
Arrived !Mail
 After return from the out of zone 
PS              PS 
(Returns to the zone)
Out of Zone           ZT
PBX        ST M Server 
(Exter nal Equipment)
OAI
Mail
➁Signal: PS returned the zone!
➂STM (retransmission)
➂  Signal: PS released!           ZT
PBX        ST M Server 
(Exter nal Equipment)       PS 
(Released)
➃STM (retransmission)
 
OAI
Mail
 
 
Case 1: PS in Idle State
Case 2: PS in Busy State
Case 3: PS In Out of Zone State 
						

							CHAPTER 4 ND-70290 (E)
Pag e 1 86
Revision 3.0
SHORT TEXT MESSAGE SERVICE
2. OPERATING PROCEDURE
 By using PS function key, user can set a password (less than 4 digits) to the PS to enter STM (short text
message system) mode, if more details are required, please refer to “PS’s manual”.
 The STM transmitted to the PS while PS’s buffer (max. 10 messages) is busy is temporarily kept in STM
server. When requesting the STM, delete old STM data in the buffer using function Key. Then the PS
automatically requests STM server to retransmit the STM. If more details are required, please refer to “PS’s
manual”.
3. SERVICE CONDITIONS
1. This feature is available only for My Line (L1) of a two-line Dterm PS. (Not provided for Sub line (L2))
2. This feature is provided in the same form as that for call termination.
3. STM Message transmission route is only one way: STM server → PS.
4. An STM can contain 128 byte data in the maximum.
5. The followings are not available in this feature.
 Call Forwarding-All Calls
 Call Forwarding-Don’t Answer
 Call Forwarding-Busy Line
 Call Forwarding-PS Incoming Incomplete
6. This feature is counted as CS peg count.
7. If the following occur, STM is not distributed, but stays in the mail box of the STM server. The STM is later
safely transmitted by this feature’s retransmission function.
 Addressee PS is out of zone.
 Addressee PS has a power down.
 The line of addressee PS is busy.
 PS is in a state of hand-over. 
Note 
Note :
When hand-over unexpectedly starts, while the message transmission is partially in progress, this feature
sees this as a squelch disconnection and performs message retransmission after the hand-over is completed.
8. In this feature, PCS Roaming is not available.
9. Plural STM server cannot be transmitted to a single PS simultaneously. Only the earliest STM can be sent
safely.
10. Hardware Requirements: Be sure to use PS and ZT that are both supporting this feature. If other PS/ZT is
used, the following occurs at the PBX side:
 PBX sends an STM request to a PS.
 PBX cannot obtain a response signal from the PS. Also, PBX cannot identify that the PS/ZT is not
compatible with the STM feature.
 PBX judges the PS as in (and returning from) the out-of zone area.
 According to the judgement above, PBX performs adequate processing (PS is judged as returning from
the zone, and a retry of STM request is made).
4. PROGRAMMING
No data programming is required. 
						

							ND-70290 (E) CHAPTER 5
Page 187
Revision 3.0
CHAPTER 5 COMMANDS
This chapter explains some commands added or revised in the PCS system. Table 5-1 below shows the list of related
commands.
Table 5-1  List of Commands 
COMMAND 
NAMEFULL COMMAND NAME
ACS DLAssignment of CS/ZT Data for Local Data Memory
AC SDNAssignment of CS/ZT Data for Network Data Memory
AC SELAssignment of Expansion CS/ZT System Data for Local Data Memory
ACS ENAssignment of Expansion CS/ZT System Data for Network Data Memory
ACS PLAssignment of CS/ZT Peg Count Data for Local Data Memory
AHRTLAssignment of Home PBX Routing Number Data for Local Data Memory
ALVPLAssignment of LVP Code for Local Data Memory
ALVPNAssignment of LVP Code for Network Data Memory
APCNLAssignment of PHS Community Data for Local Data Memory
APCNNAssignment of PHS Community Data for Network Data Memory
APDLLDownload of PS Operation Data for Local Data Memory
APDLNDownload of PS Operation Data for Network Data Memory
APSDAssignment of PS Operation Data for DM
ARODLAssignment of Roaming Self PBX Number Data for Local Data Memory
AV P DAssignment of Visitor PS Data
AV P D LAssignment of Telephone Number for Visitor PS for Local Data Memory
AV P D NAssignment of Telephone Number for Visitor PS for Network Data Memory
*ASFCAssignment of Service Feature Class
*ASPAAssignment of Special Access Code
*ASYDAssignment of System Data
*AAEDAssignment of Announcement Equipment Data
*ALGNLAssignment of Telephone Number Data for Local Data Memory
*ALGNNAssignment of Telephone Number Data for Network Data Memory
*ALGSLAssignment of Telephone Number Data for Local Data Memory
*ALGSNAssignment of Telephone Number Data for Network Data Memory
Note:An asterisk (*) indicates the commands whose contents are given slight addition or amendment in the PCS
system. This manual only describes the parts revised from the previous ones. Additionally, for more detail,
refer to “Office Data Specification” or “System Operations and Maintenance Manual” for the PBX for
commands marked with an asterisk (*). 
						

							CHAPTER 5 ND-70290 (E)
Pag e 1 88
Revision 3.0
COMMANDS
*ALRTNAssignment of Logical Route for Network Data Memory
*ANSDLAssignment of Number Sharing Data for Local Data Memory
*ANSDNAssignment of Number Sharing Data for Network Data Memory
APMDAssignment of Trunk Line Appearance Maximum Necessary Digit for DM
APMLLAssignment of PS Multiline Data for Local Data Memory
APMLNAssignment of PS Multiline Data for Network Data Memory
APSPAssignment of Trunk Line Appearance for DM
AZDLZT Program Download
AHLGAssignment of CFT Hot Line Group
AHLGLAssignment of CFT Hot Line Group for LDM
AHLGNAssignment of CFT Hot Line Group for NDM
*AT R FAssignment of Traffic Measurement Order
AZARLAssignment of ZT Area Information for Local Data Memory
AZARNAssignment of ZT Area Information for Network Data Memory
COCS1LControl of CS/ZT Status Read for Local Data Memory
COCS1NControl of CS/ZT Status Read for Network Data Memory
COCS2LChange of CS/ZT Operation Parameter for Local Data Memory
COCS2NChange of CS/ZT Operation Parameter for Network Data Memory
COCS3LControl of CS/ZT Reset for Local Data Memory
COCS3NControl of CS/ZT Reset for Network Data Memory
DLINDisplay of a List of Roaming PS
DPSNDisplay of PS Station Data
DRPSDisplay of Reverse Develop PS Data
DTFPDisplay of CS/ZT Peg Count Data
MBCSLMake Busy of CS/ZT for Local Data Memory
MBCSNMake Busy of CS/ZT for Network Data Memory
Table 5-1  List of Commands  (Continued)
COMMAND 
NAMEFULL COMMAND NAME
Note:
An asterisk (*) indicates the commands whose contents are given slight addition or amendment in the PCS
system. This manual only describes the parts revised from the previous ones. Additionally, for more detail,
refer to “Office Data Specification” or “System Operations and Maintenance Manual” for the PBX for
commands marked with an asterisk (*). 
						

							ND-70290 (E) CHAPTER 5
Page 189
Revision 3.0
COMMANDS
1. COMMAND DESCRIPTION AND DA T A   S H E E T   F O R   A S S I G N M E N T
This chapter explains assignment commands and their parameters for this system. The contents of each
assignment command description are illustrated in Figure 5-1.
Figure 5-1  Command Descriptions
Command name
The assigned data dump  into the designated file by the 
list up command shown here.Command name (full name)
The purpose of command and the related service
feature are explained here.
Peripheral notice necessary to create the office data
which may include the following:
The related command and parameters
The related service feature
MAT operation instructions 
The system hardware operation to be affect the data
The data storage node within the fusion network          
The required parameters, the applicable data range and
parameter descriptions are explained here.     
AFDD
List Up: LFDD
1. GENERAL
2. PRECAUTIONS
3.DATA ENTRY INSTRUCTIONS
DISP
DISPLAY MESSAGE ON LCD (DISP) FUNCTION KEY CODE (FKY)1-320
FKY FKYService name Service nameD efa ult display Defau lt d is pla y
Assignment of Function Display Data
This command is used to assign the characters of software key indication on a D      Series E.
When this command is not assigned, the default(which shows on FKY parameter description on this command)
are displayed.
The LCD is 24 digits wide, and there are four of software keys, hence a maximum of 6 characters can be assigned
for each software key indication.
Displayed characters (Max. 6 characters of alphabet and numbers)
1FWD-BY
FKY(1-320) Note:The default displayed characters are shown in the parenthesis
1
2
3
4
5
6
7Call Forwarding-Busy Line
Call Forwarding-All Calls
Executive Right of Way
Call Waiting
CAll Back
-
Save  and Repe atFDB
FDA
BV
CW
CB
-
S&R
-60
61-82
83
84
85
86
87Manual Signaling Key
-
Retain Conference
Serial Call
Internal Zone Paging (Not released
for U.S.A.  an d Ca na da)
-
W ake  Up SetSIG
-
KEEP
S_CAL
IZP
-
WUS
term 
						

							CHAPTER 5 ND-70290 (E)
Pag e 1 90
Revision 3.0
ACS DL
ACSDL  : Assignment of CS/ZT Data for Local Data Memory
1. GENERAL
This command is used to assign, delete, and display the CS/ZT-related data. A CSINT circuit card can
accommodate four CSs/ZTs, allowing each two groups of the Levels 0 and 4 to be assigned for one circuit card.
List Up Command: LCSDL
2. PRECAUTIONS
1. This command is used for the Local Node.
2. When assigning LENS, CS/ZT should be assigned in the Group of less than 24 and the Levels to be available
are 0 and 4.
3. While the CS/ZT is busy, the data cannot be deleted.
3. DATA ENTRY INSTRUCTIONS
PCN
GRNEnter the PCN (PHS Community Number)
Note: Group NO. available for inter-node
          of the Fusion Network
Enter the GRN (Group
Number)TN
Enter the TN (Tenant Number)
ERN
Enter the ERN (Calling 
Area Number)CSN / ZTN
Enter the CS / ZT number
1 = V1CS (Not used)
2 = V2CS (Not used)
3 = ZT1
4 = ZT2KIND
PHS
COMMUNITY
NUMBER
(PCN )
1 - 1024CALLING AREA
NUMBER
 (ERN )
1 - 32GROUP
NUMBER
 (GRN )
1 - 8TENANT
NUMBER
(TN )
1 - SYSTEM MAXEQUIPMENT
NUMBER
(LENS ) CS / ZT  NUMBER
 (CSN / ZTN )
1 - 32CS / ZT  KIND
 (KIND )
1 - 4 
						

							ND-70290 (E) CHAPTER 5
Page 191
Revision 3.0
AC SDL
4. DATA SHEET
CS/ZT Data Assignment Sheet
PHS 
COMMUNITY 
NUMBER
(PCN)
1-1024CALLING 
AREA NO.
(ERN)
1-32GROUP 
NO.
(GRN)
1-8CS/ZT 
NO.
(CSN/
ZTN)
1-32TENANT 
NUMBER
(TN)
1-
SYSTEM 
MAXLENS
CS/ZT 
KIND
(KIND)
3, 4 MG 
00-07U
0-3G
00-23LV  
0/4 
						

							CHAPTER 5 ND-70290 (E)
Pag e 1 92
Revision 3.0
ACS DN
ACSDN  : Assignment of CS/ZT Data for Network Data Memory
1. GENERAL
This command is used to assign, delete and display the CS/ZT-related data of the Network Control Node (NCN).
A CSINT circuit card can accommodate four CSs/ZTs, allowing each two groups of the Levels 0 and 4 to be
assigned for one circuit card.
List Up Command: LCSDN
2. PRECAUTIONS
1. This command is used for the Network Control Node.
2. When assigning LENS, CS/ZT should be assigned in the Group of less than 24 and the Levels to be available
are 0 and 4.
3. The same ERN cannot be assigned to multiple nodes.
4. When you want to move ERN from A node to B node, you must delete each CS/ZT in the ERN of A node.
5. When assigning/deleting the CS/ZT-related data of the NCN, you must back up the Office data of the NCN
and the LN that mounts the CS. 
						

							ND-70290 (E) CHAPTER 5
Page 193
Revision 3.0
ACS DN
3. DATA ENTRY INSTRUCTIONS
PCN
GRN
Enter the PCN (PHS Community Number)
Note: Group NO. available for inter-node
           of the Fusion Network
Enter the GRN (Group 
Number)TN
Enter the TN (Tenant Number)
PHS
COMMUNITY
NUMBER
 ( PCN )
1 - 1024FUSION
POINT CODE
( FPC )
1 - 253CALLING 
AREA
NUMBER
 ( ERN )
1 - 32GROUP
NUMBER
 ( GRN )
1 - 8TENANT
NUMBER
( TN )
1-SYSTEM MAX
EQUIPMENT
NUMBER
( LENS ) CS / ZT  
NUMBER
 ( CSN / ZTN )
1 - 32CS / ZT  KIND
 ( KIND )
1 - 4
FPC
Enter the FPC in the
 Fusion NetworkERN
Enter the ERN (Calling 
Area Number)CSN / ZTN
Enter the CS / ZT number
1 = V1CS (Not used)
2 = V2CS (Not used)
3 = ZT1
4 = ZT2KIND