NEC Neax 2400 Imx Wireless System Manual

							CHAPTER 5 ND-70290 (E)
Pag e 2 44
Revision 3.0
ASPA
ASPA  : Assignment of Special Access Code
1. GENERAL
This command is used to determined the kind of service and its Access Code to be executed.
List Up Command: LSPA
2. PRECAUTIONS
This part describes only the content of the command added in the PCS system. For more details, refer to the
“Office Data Specification”. 
						

							ND-70290 (E) CHAPTER 5
Page 245
Revision 3.0
ASPA
3. DATA ENTRY INSTRUCTIONS
Access code (Max. 6 digits)
TENANT
NUMBER
( TN )ACCESS CODE
( ACC )
MAX. 6 DIGITSCONNECTION STATUS
ACC
CI
N = Normal service
H = Hooking service
B = Busy service
INDEX
( CI )KIND OF
SERVICE ( SRV )
SRV
STN = Station
SSCA = Service code appendix
OGCA = Outgoing call with route advance
LCR = Least cost routingSSC = Service code 
OGC= Outgoing call 
UNIF = Office termination
ANNC = Announcement service-single announcement 
ANNCM = Announcement service-multiple announcement 
PAGA = Paging answer LCRS= Register sender LCR
PAGC = Paging cancel 
						

							CHAPTER 5 ND-70290 (E)
Pag e 2 46
Revision 3.0
ASPA
When SRV = SSCA (Service code appendix) is assigned; 
NND appears when SIDA=97 (Call Hold Conference).
The number of digits for an access code should be assigned in NND. NND
SERVICE INDEX  A ( SIDA ) 1 - 255 NECESSARY DIGIT ( NND ) 1 - 6
1-100Note
101
102C.F-PS Incoming Incomplete: Set
C.F-PS Incoming Incomplete: Cancel
103~107
Note
SIDA
SIDA Service Name
108
109
110~113
114
115
116~255Number Sharing : Set
Number Sharing : Cancel
Call Forwarding-Dropped Calls : Set
Call Forwarding-Dropped Calls : Cancel
Note Note
Note:  See the “Office Data Specification” regarding this data. 
						

							ND-70290 (E) CHAPTER 5
Page 247
Revision 3.0
ASPA
4. DATA SHEET
 SRV=SSCA Service code Appendix
Note:Refer to the “Office Data Specification” regarding this data.
TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION
STATUS 
INDEX
(CI) N/H/BKIND OF
SERVICE
(SRV)SERVICE
FEATURE
INDEX
(SIDA)
1 - 255NUMBER
OF NEC-
ESSARY
DIGITS 
(NND)SERVICE CONTENTS
1
100
Note 
NNormal
SSCA 101Call Forwarding Incoming 
Incomplete Set H Hooking
BBusy
NNormal
SSCA 102
Incoming Incomplete Cancel
H Hooking
BBusy
103
107
Note 
NNormal SSCA 108Number Sharing; Set
NNormal SSCA 109
Number Sharing; Cancel
110
113
Note 
NNormal SSCA 114Call Forwarding-Dropped 
Calls ; Set
NNormal SSCA 115
Call Forwarding-Dropped 
Calls ; Cancel
116
255
Note 
~
~
~
~ 
						

							CHAPTER 5 ND-70290 (E)
Pag e 2 48
Revision 3.0
ASYD
ASYD  : Assignment of System Data
1. GENERAL
The ASYD/ASYDL command is used to assign the system data of the following node;
Local Node (LN) / Network Control Node (NCN) of the Fusion network.
Stand alone PBX.
List Up Command: LSYD
2. PRECAUTIONS
This part describes only the contents of the command added in Built-in PCS system. For more details, refer to
the “Office Data Specification.” 
						

							ND-70290 (E) CHAPTER 5
Page 249
Revision 3.0
ASYD
3. DATA ENTRY INSTRUCTIONS
Define each bit corresponding
data with referring to the
SYSTEM DATA CONTENTS
SYSTEM
DATA
TYPE
( SYS )DATA
( DATA )
00-FF
( Hex ) SYSTEM
DATA
INDEX
( INDEX )
0 - 511
BIT CORRE-
SPONDING
DATA
DATA
0 / 1BITSYSTEM DATA CONTENTS
DATA
DATA BIT
BIT
DATA
Hex 1
1b0
b1
b2
b3
b4
b5
b6
b7 1
0
0
0
0
0
0n
n+1 FF031
1
0
0
0
0
0
0b0
b1
b2 Not used
Not used
Not used
Not used
Not used
Not used
Number of zzz b3
b4
b5
b6
b7xxx service 0/1=Not to be provided/  To be provided
yyy service 0/1=Not to be provided/  To be provided
Convert from Binary DATA
to Hexadecimal, and enter the
Hex. value at DATA text box.
00000011 b7 b6 b5 b4 b3 b2 b1 b0
03 
						

							CHAPTER 5 ND-70290 (E)
Pag e 2 50
Revision 3.0
ASYD
SYSTEM
DATA
TYPE 
(SYS)SYSTEM 
DATA  
INDEX 
(INDEX)
0 - 511DATA 
(DATA) 
00-FF 
(Hex)BIT CORRE-
SPONDING 
DATA
SYSTEM DATA CONTENTS
DATA 
0/1BIT
15b
0
Access Code for C.F.-Busy Line and C.F. – Don’t Answer Services
0/1 = Same/Separate
Note 1:If a PCS system, C.F.-PS Incoming Call Incomplete also
refers to this system data.
Note 2:If “0” is assigned, assign either SID: 10 or 12 in
command “ASPA”.
b
1Maximum number of Multiple Call Forwarding – All Calls/Busy 
Line occurrences:
Note:This data is valid when SYS-1, INDEX 69, bit 7 is assigned
as “1”. b
2
b3
b4Miscellaneous Timer Counter 
(MTC)
(0-7)Call Back – Delay Timer
Timer Value Setting is MTC × 2 
sec.
When this data is “000”, Timer 
value is 2 sec. b
5
b6
b7Call Back – Delay Timer
0/1 = Ineffective/Effective
b3b2b1b3b2b1
000: 100:
001: 101:
010: 110:
011:111:
once
three times twice
five times four times 
						

							ND-70290 (E) CHAPTER 5
Page 251
Revision 3.0
ASYD
4. SYSTEM DATA PROGRAMMING SHEET (1)
S
Y
S
1
SYSTEM
DATA
INDEX
0-511DATA
00-FFB
I
TSYSTEM DATA CONTENTS
30 060 Mounting Capacity of Data Memory (DM) : 1~63 Mbyte (01~3F) 
Normally assigned as “6” 
1
2
3
4
5
6
7
4200Access code using Pre-set dialing
 (e.g.: Special Access Code + Station number)
0/1 : Out/In service
1By cancelling C.F.-PS INCOMING INCOMPLETE
0 = C.F.-DROPPED CALL is also cancelled
1 = C.F.-DROPPED CALL is not cancelled
2Not used
3
4
5
6
7
b7 b6 b5 b4 b3 b2 b1 b0
00
Data
b7 b6 b5 b4 b3 b2 b1 b0
0000000
Data 
						

							CHAPTER 5 ND-70290 (E)
Pag e 2 52
Revision 3.0
ASYD
S
Y
S
1
SYSTEM
DATA
INDEX
0-511DATA
00-FFB
I
TSYSTEM DATA CONTENTS
4210 Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.1) Announcement PS-Out of 
Zone disconnection timer 
(Release Guard timer)
Timer value setting is as 
follows: (TC) sec. × (MTC)
When the data is assigned as 
00, the default data is 30 sec. 1
2
3
4 Timer class (TC)
0 : –  3 : 2 sec.  6 : –
1 : – 4 : – 7 : –
2 : –  5 : – 5
6
7 Not used
4220Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.2) No-tone connection timer to 
the called party during the 
handover
Timer value setting is as 
follows: 800 msec.+ (TC) × 
(MTC)
When the data is assigned as 
00, the default data is 800 
msec. 1
2
3
4Timer class (TC)
0 : –  3 : –  6 : –
1 : 64 msec. 4 : –  7 : –
2 : –  5 : – 5
6
7Not used
4230 Miscellaneous Time Counter (MTC) is 
to be assigned a value from 1 Hex to F 
Hex.3) ZT start-up Guard Timer 
when initialization is in 
progress.
(This is the timer by which 
the ZT is placed out of Zone 
and made send PS location 
registration.)
Timer value setting is as 
follows: (TC) sec.× (MTC)
When the data is assigned as 
00, the default data is 60 sec. 1
2
3
4 Timer class (TC)
0 : –  3 : 2 sec.  6 : –
1 : – 4 : 30 sec. 7 : –
2 : –  5 : – 5
6
7Not used
b7 b6 b5 b4 b3 b2 b1 b0
0
b7 b6 b5 b4 b3 b2 b1 b0
0
b7 b6 b5 b4 b3 b2 b1 b0
0 
						

							ND-70290 (E) CHAPTER 5
Page 253
Revision 3.0
AAED
AAED  : Assignment of Announcement Equipment Data
1. GENERAL
This command is used to assign the trunk information related to Announcement Equipment on a tenant basis. 
List Up Command: LAED
2. PRECAUTIONS
This part describes only the contents of the command added in PCS system. For more details, refer to the “Office
Data Specification”.