NEC Neax 2400 Imx Wireless System Manual

							CHAPTER 3 ND-70290 (E)
Pag e 7 4
Revision 3.0
PA-4CSIF (CSINT)
PA-4CSIF (CSINT)  : ZT (Zone Transceiver) Interface
1. General Functions
This card is a line circuit card which accommodates Zone Transceivers (ZTs) via the ISDN U interface. ZTs
are to be connected using NT1.
The main specifications and functions of this circuit card are shown below.
 A maximum of four ZTs can be accommodated in one circuit card.
 Interface with the NT1 is based on the standard ISDN interface. (U reference-point Echo Canceller
method. ANSI TI.601, Q.921 interface)
 Two B channels of each 32 kbps can be used in 2B+D with the total speed of 64 kbps.
 Sealing current (Maximum 15 mA) can be supplied to protect cables from rusting.
 Equipped with ADPCM which enables the B-channel bit rate to change. (TSW-side: 64 kbps, ZT side:
32 kbps)
Figure 3-13  Location of Card in System
2. Mounting Location of Circuit Card and Its Conditions
 Mounting location of circuit card: Universal slot of the PIM
Conditions: 12 CSINT circuit cards can be mounted in one PIM
ZT
I.430PS
PS
TSW
PLO PA-4CSIF
ANSI TI.601
NT1 
						

							ND-70290 (E) CHAPTER 3
Page 75
Revision 3.0
PA-4CSIF (CSINT)
3. Lamps, Switches, Connectors and Their Location
The following diagram shows the location of Lamp, Key and Connectors.
Figure 3-14  Lamp, Key and Connectors : PA-4CSIF
OPE
MB
MODE
SW21NOPE
MBRL3
L2
L1
L0
SW12
SW11
SW20
SW10LPB
L3
L2
L1
L0
MONITOR (Not used)
BL34
BER3 BL33
LYR3 BL32
BL24
BER2 BL23
LYR2 BL22
BL14
BER1 BL13
BL12
LYR1
BL04
BER0 BL03
BL02
LYR0 
						

							CHAPTER 3 ND-70290 (E)
Pag e 7 6
Revision 3.0
PA-4CSIF (CSINT)
4. Lamp Indication
Shown below are the contents of lamp indication on this circuit card.
n=0~3
Note 1:B2 through B4 channels represent channel names of 32K ADPCM.
Note 2:Establishment of synchronization on U Reference Point may take 30 seconds or more.
LAMP NAME COLOR MEANING
OPE Green Remains lit when the card is operating normally.
NOPE Red Remains lit when the card is in make-busy state.
BLn4Green  Remains lit when B4 channel of the line #n is communicating  (
Note).
Flashing Flashes while the corresponding circuit is in make-busy state (60 IPM).
Off Remains off while the corresponding circuit is idle.
BLn3Green Remains lit when B3 channel of the line #n is communicating  (
Note).
Flashing Flashes while the corresponding circuit is in make-busy state (60 IPM).
Off Remains off while the corresponding circuit is idle.
BLn2Green Remains lit when B2 channel of line #n is communicating  (
Note).
Flashing Flashes while the corresponding circuit is in make-busy state (60 IPM).
Off Remains off while the corresponding circuit is idle.
LY R nGreen Remains lit when the layer 2 link of line #n is established.
FlashingFlashes when synchronization is established on Layer 1 of S Reference Point 
(60 IPM).
Flashes when synchronization is established on Layer 1 of U Reference Point 
(120 IPM).
Off Synchronization is not established on both Layer 1 and Layer 2.
BERnRedTwo or more CRC errors occur per second and the condition lasts for 10 
seconds.
Off One or no CRC error occurs per second. 
						

							ND-70290 (E) CHAPTER 3
Page 77
Revision 3.0
PA-4CSIF (CSINT)
5. Switch Settings
Switches on this card have the following meanings.
SWITCH NAMESWITCH 
NUMBERSWITCH 
SETTINGSTANDARD 
SETTINGMEANING
MB
 (Toggle Switch)
UPCircuit card make-busy
DOWN×Circuit card make-busy cancel
MBR
 
(Piano Switch)
0ON Line 0 make-busy request
OFF×Line 0 make-busy request cancel
1ON Line 1 make-busy request
OFF×Line 1 make-busy request cancel
2ON Line 2 make-busy request
OFF×Line 2 make-busy request cancel
3ON Line 3 make-busy request
OFF×Line 3 make-busy request cancel
LPB
 (Piano Switch)
0ON Loop back is set on NT1 for Line 0.
OFF×Loop back is canceled on NT1 for Line 0.
1ON Loop back is set on NT1 for Line 1.
OFF×Loop back is canceled on NT1 for Line 1.
2ON Loop back is set on NT1 for Line 2.
OFF×Loop back is canceled on NT1 for Line 2.
3ON Loop back is set on NT1 for Line 3.
OFF×Loop back is canceled on NT1 for Line 3.
MODE 
(Rotary Switch)
0×Fixed
1~FNot used
SW10 
(DIP Switch)
1ON Mounted in WCS
OFF×Mounted in PCS
2ON×Fixed
3ON×µ-law
OFF A-law
4ON×Fixed
ON (MB)
OFF
No. 3
No. 2
No. 1
No. 0OFF
ON
No. 3
No. 2
No. 1
No. 0OFF
ON
ON
12
34 
						

							CHAPTER 3 ND-70290 (E)
Pag e 7 8
Revision 3.0
PA-4CSIF (CSINT)
SWITCH NAMESWITCH 
NUMBERSWITCH
SETTINGSTANDARD 
SETTINGMEANING
SW11 1 ON×
Fixed
2ON×
Fixed
3ON×
Fixed
4ON×
Fixed
5ON×PB Sender Mode (Law/Level)
Note:µ/A-law can be selected on the TSW side
PA D .
µ-law standard = High: –7.0 dBm
Low: –9.0 dBm
A-law standard = High: –8.0 dBm
Low: –10.0 dBm OFF
6ON×
OFF
7ON×
Not used
8ON Sealing Current is not supplied.
OFF×
Sealing Current is supplied.
(DIP Switch)
ON
12
3456
78
SW5 SW6 LAW/LEVEL
OFF OFF Not used
ON OFF
OFF ON
ON ONµ-law standard
A-law standard 
Note  
						

							ND-70290 (E) CHAPTER 3
Page 79
Revision 3.0
PA-4CSIF (CSINT)
[Firmware: SW-360]
Note 1:
PAD control is shown below.
SWITCH NAMESWITCH 
NUMBERSWITCH 
SETTINGSTANDARD 
SETTINGMEANING
SW12
(DIP Switch)
1~8
ON
12
3456 78
Connection with C.O. Note
Connection with a station  Note
SWITCH 1 SWITCH 2 SWITCH 3 PAD VALUE
OFF OFF OFF Not used
ON OFF OFF Not used
OFF ON OFF PAD 1=3 dB
ON ON OFF PAD 1=0 dB
OFF OFF ON PAD 1=–3 dB
ON OFF ON PAD 1=–5 dB
(Standard setting)
OFF ON ON PAD 1=–7 dB
ON ON ON PAD 1=–10 dB
SWITCH 4 PAD VALUE
ON PAD 2=3 dB (Standard setting)
OFF PAD 2=0 dB
SWITCH 5 SWITCH 6 SWITCH 7 PAD VALUE
OFF OFF OFF Not used
ON OFF OFF PAD 1=5 dB
OFF ON OFF PAD 1=3 dB
ON ON OFF PAD 1=0 dB
(Standard setting)
OFF OFF ON PAD 1=–3 dB
ON OFF ON PAD 1=–5 dB
OFF ON ON PAD 1=–7 dB
ON ON ON PAD 1=–10 dB
SWITCH 8 PAD VALUE
ON PAD 2=3 dB
OFF PAD 2=0 dB (Standard setting)
PAD 1
PAD 2 TSW Side
Line Side 
						

							CHAPTER 3 ND-70290 (E)
Pag e 8 0
Revision 3.0
PA-4CSIF (CSINT)
SWITCH NAMESWITCH 
NUMBERSWITCH
SETTINGSTANDARD 
SETTINGMEANING
SW20 1 OFF×Fixed
2OFF×Fixed
3OFF×Fixed
4OFF×Fixed
SW21 1 ON×Not used
2ON×Not used
3ON×Not used
4ON×Not used
5ON×Not used
6ON×Not used
7ON×Not used
8ON×Fixed
(DIP Switch)
ON
12
34
(DIP Switch)
ON
12
3456
78 
						

							ND-70290 (E) CHAPTER 3
Page 81
Revision 3.0
PA-4CSIF (CSINT)
PA-4CSIF (CSINT) : ZT (Zone Transceiver) Interface
Switch Setting Table
MODULE
NAMESLOTSWITCH 
NAMESWITCH SHAPE REMARKS
PIM MB ON : Make-busy set of circuit 
card 
OFF : Make-busy cancel of 
circuit card
MBR
LPB
MODE
SW10
SW11
SW12
SW20
SW21
ON
No. 3
No. 2
No. 1
No. 0OFF
ON
No. 3
No. 2
No. 1
No. 0OFF
ON
0
ON
1234
ON
12
3456 78
ON
12
3
456 78
ON
1234
ON
12
3
456 78 
						

							CHAPTER 3 ND-70290 (E)
Pag e 8 2
Revision 3.0
PA-4CSIF (CSINT)
6. External interface
Shown in Figure 3-15 are accommodation of the LT connector leads of this circuit card and connecting route
diagram.
a. When this circuit card is mounted in PIM.
Figure 3-15  LT Connector Leads Accommodation of PIM : PA-4CSIF
26272829303132333435363738394041
1234567891011121314151642434445464748
1718192021222349502425
Accommodated in *1
LT0, 2, 4, 6, 8, 10 Connector
LT Connector Accommodation
26272829303132333435363738394041
1234567891011121314151642434445464748
1718192021222349502425
Accommodated in *2
LT1, 3, 5, 7, 9,11 Connector
26272829303132333435363738394041
1234567891011121314151642434445464748
1718192021222349502425
Accommodated in *3
LT1, 3, 5, 7, 9, 11 Connector
232221201918171615141312111009080706050403020100
LT6 LT7 LT8 LT9 LT10 LT11LT0 LT1 LT2 LT3 LT4 LT5
23 19 15
22 18 14
21 17 13
20 16 1223 19 15
22 18 14
21 17 13
20 16 12 11 09 07 05 03 01
10 08 06 04 02 00 11 09 07 05 03 01
10 08 06 04 02 00
Group No.
Slot No.
LT Connector Name
PIM
32
**
Highway Block
01324567981011 2*
1*
1*
2*
3*
1*
3*
1*
3*
1*
3*
2*
1*
3*
2* B0
B1
B2
B3A0
A1
A2
A3
2* B0
B1
B2
B3A0
A1
A2
A3
B0
B1
B2
B3A0
A1
A2
A3
PWR PWR 
						

							ND-70290 (E) CHAPTER 3
Page 83
Revision 3.0
PA-4CSIF (CSINT)
Figure 3-16  Connecting Route Diagram
MDF
PIM
NT1 A
B
CSINTA
B