Konica Minolta magicolor 4695MF User Manual

							Status, Error, and Service Messages 297
Trans. Roll. LifeThe time to replace 
the transfer roller 
has been reached.Replace the transfer 
roller.
TRAYx OPEN
CLOSE TRAYxThe indicated paper 
tray is open.Close the indicated 
paper tray.
UNABLE TO
COLLATE JOBSince the hard disk 
(area for saving 
copies when print-
ing sets) is full, cop-
ies cannot be 
printed as sets.Print only one set at a 
time, or reduce the 
number of pages to be 
printed.
USB Dev. Not supportA USB device 
incompatible with 
this machine is con-
nected.Disconnect the USB 
device from this 
machine.
USB Hub Not supportA USB hub is con-
nected to this 
machine.This machine is not 
compatible with a USB 
hub. When connecting 
USB cables to this 
machine, do not use a 
USB hub.
USB MEMORY FULLThere is no space 
available on the 
USB memory 
device connected to 
this machine.Delete data from the 
USB memory device to 
create free space, or 
use a different USB 
memory device.
xxx COVER OPEN
CLOSE xxx COVERThe indicated cover 
is open.Close the indicated 
cover.
xxx DOOR OPEN
CLOSE xxx DOORThe indicated door 
is open.Close the indicated 
door.
xxx SERVER ERRORThe file cannot be 
saved on the indi-
cated server.Check the status of the 
indicated server.
WASTE TONER FULL
REPLACE BOTTLEThe waste toner 
bottle is full.Replace the waste 
toner bottle.
Waste Near FullThe waste toner 
bottle will soon be 
full.Prepare a waste toner 
bottle. This message... means... Do this...
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 298
Wrong I-Unit xAn imaging unit 
incompatible with 
the machine is 
installed.Replace the indicated 
imaging unit with a cor-
rect one.
WRONG PASSWORD
xxxThe password is 
incorrect, so the 
indicated server 
could not be 
accessed.Check the password, 
and then specify the 
correct one.
Wrong Toner xA toner cartridge 
incompatible with 
the machine is 
installed.Replace the indicated 
toner cartridge with a 
correct one.
xxx IS DISABLEDThe TCP/IP, FTP, 
SMTP or SMB set-
tings are disabled.Enable the TCP/IP, 
FTP, SMTP or SMB 
settings.
DESTINATION SET 
BY MANUAL UP TO 16There were more 
than 16 addresses 
found with an LDAP 
search.Increase the number of 
entered characters, 
and then perform the 
search again. This message... means... Do this...
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 299 Service Messages
These messages indicate a more serious fault that can only be corrected by a 
customer service engineer. If one of these messages appears, turn the 
machine off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
This service message... means... Do this...
MACHINE TROUBLE
SERVICE CALL (xxxx)An error has been 
detected with the item 
indicated “
xxxx” in 
the service message.Reboot the machine. 
This often clears the 
service message, 
and machine opera-
tion can resume. 
If the problem per-
sists, contact Techni-
cal Support.
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 300
Downloaded From ManualsPrinter.com Manuals 
						

							12
12Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 302
Introduction
Note
Any damage to the machine caused by the use of accessories not 
manufactured or supported by KONICA MINOLTA will void your 
warranty. 
This chapter provides information about the following accessories.
Note
The hard disk kit and CF adapter cannot be installed to be used at the 
same time. 
Installing accessories always requires that the machine and 
accessories are turned off and unplugged during installation.
For details on the available options, refer to 
http://printer.konicaminolta.com. Dual In-Line 
Memory Module 
(DIMM)256 MB, 512 MB DIMM
(DDR2-667 SO-DIMM, 166 MHz, 200pins, No ECC, 
Unbuffered, CL=3)
Density : 512 Mbits
Organization : 64 Mwords x 8 bits
Tray 3Lower feeder unit with 500-sheet tray included
Hard Disk Kit40GB Hard Disk
CF AdapterAdapter for CompactFlash card
CompactFlash512 MB, 1GB, 2GB, 4GB
Downloaded From ManualsPrinter.com Manuals 
						

							Antistatic Protection 303
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present. Plastic, rubber, wood, painted metal surfaces, and telephones 
are not acceptable grounding points.
If you don’t have an antistatic wrist strap, discharge your body’s static 
electric charge by touching a grounded surface before you handle any 
printer boards or components. Also avoid walking around after 
grounding yourself.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 304
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing.
This machine detects only half of the amount of the installed memory.
Dual in-line memory module (or DIMM) is compact circuit board with 
surface-mount memory chips.
There is 256 MB of onboard memory and one available memory 
expansion slot. The memory can be expanded to a maximum of 
768 MB (256 MB + 512MB).
Installing a DIMM
Note
Its very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 253. In addition, 
always handle circuit boards by the edges only.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 305
2Remove the rear cover.
3Using a screwdriver, loosen the 
screw.
Do not remove any screw 
other than the one 
indicated in the 
illustration.
4Open the inside cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 306
5Insert the new DIMM straight 
into the DIMM connector until 
the latches snap into the locked 
position.
Observe the keyed side of the 
DIMM to align it with the connec-
tor. If you cannot snap the DIMM 
into place, do not force it. Repo-
sition it, making sure that the 
DIMM is seated completely in 
the connector.
6Close the inside cover, and then tighten the screw.
7Close the rear cover.
8Reconnect all interface cables.
9Reconnect the power cord, and 
turn on the machine.
10Declare the additional Printer 
Memory in the Windows printer driver (Properties/Configure tab).
11Print a configuration page (REPORT/STATUS / REPORT / CONFIGU-
RATION PAGE
) and verify that the total amount of the RAM installed in 
your printer is listed.
Downloaded From ManualsPrinter.com Manuals