Konica Minolta magicolor 4695MF User Manual

							Printing a Configuration Page 247
Printing a Configuration Page
1
In the main screen, press the + or , key to select REPORT/STATUS, 
and then press the Select key.
2Press the + or , key to select REPORT, and then press the Select key.
3Press the + or , key to select CONFIGURATION PAGE, and then press 
the Select key.
4Press the Start-B&W key or the Start-Color key.
Downloaded From ManualsPrinter.com Manuals 
						

							Unlocking the Scanner 248
Unlocking the Scanner
1
Lift open the ADF cover.
2Move the scanner lock lever to 
.
3Close the ADF cover.
4Turn off the machine, and then turn it on again.
Downloaded From ManualsPrinter.com Manuals 
						

							Preventing Media Misfeeds 249
Preventing Media Misfeeds
Make sure that...
Media matches the machine specifications.
Media is flat, especially on the leading edge.
The machine is on a hard, flat, level surface.
You store media in a dry location away from moisture and humidity.
You remove transparencies from the output tray immediately after printing to 
avoid static buildup.
You always adjust the media guides in Tray 2/3 after inserting the media (a 
guide that is not properly adjusted can cause poor print quality, media mis-
feeds, and machine damage).
You load the media printing-side up in the tray (many manufacturers place 
an arrow on the end of the wrapper to indicate the printing side).
Avoid...
Media that is folded, wrinkled, or excessively curled.
Double feeding (remove the media and fan the sheets—they may be sticking 
together). 
Fanning transparencies since this causes static.
Loading more than one type/size/weight of media in a tray at the same time.
Overfilling the trays. 
Allowing the output tray to overfill (the output tray has a 250 sheet capac-
ity—misfeeding may occur if you allow more than 250 sheets of media to 
accumulate at one time).
Allowing the output tray to fill with more than a few transparencies. 
Downloaded From ManualsPrinter.com Manuals 
						

							Understanding the Media Path 250
Understanding the Media Path
Understanding the media path will help you locate media misfeeds.
1. ADF media feed rollers
2. Document feed tray
3. Document output tray
4. Toner cartridge
5. Fuser unit
6. Duplex
7. Tray 1 (manual feed tray)
8. Tray 3 (optional lower feed 
unit)
9. Tray 2
10. Laser
11. Imaging unit
12. Transfer belt unit
13. Output tray
Clearing Media Misfeeds 
To avoid damage, always remove misfed media gently, without tearing it. Any 
piece of media left in the machine, whether large or small, can obstruct the 
media path and cause further misfeeds. Do not reload media that has misfed.
Note
The image is not fixed on the media before the fusing process. If you 
touch the printed surface, the toner may stick to your hands, so be 
careful not to touch the printed face when removing the misfed media. 
Make sure not to spill any toner inside the machine. 
413
11 12
7
5
6
10
9
8
3
12
Media path Document path
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds 251
CAUTION
Unfused toner can mess your hands, clothes, or anything else it gets 
on.
If you accidentally get toner on your clothes, lightly dust them off as 
best as you can. If some toner remains on your clothes, use cool, not 
hot water, to rinse the toner off. If toner gets on your skin, wash it off 
with cool water and a mild soap.
CAUTION
If you get toner in your eyes, wash it out immediately with cool water 
and consult a doctor.
If, after clearing the media misfeed, the misfeed message in the message 
window persists, open and close the engine cover. This should clear the mis-
feed message. 
Media Misfeed Messages and Clearing Procedures
Media Misfeed Message Page Reference
PAPER MISFEED
OPEN RIGHT DOORpage 255
PAPER MISFEED
OPEN TRANSPORT DOORpage 258
FUSER JAM
OPEN RIGHT DOORpage 264
TRANSFER ROLLER JAM
OPEN TRANSPORT DOORpage 258
VERTICAL TRANS JAM
OPEN RIGHT DOORpage 255
DUPLEX LOWER JAM
OPEN RIGHT DOORpage 263
DUPLEX UPPER JAM
OPEN RIGHT DOORpage 263
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds 252
Clearing a Media Misfeed from Tray 1 (Manual Feed Tray) 
and Transfer Roller
1Pull the lever, and then open the 
right door.
Before opening the right 
door, fold up Tray 1.
MP TRAY JAM
OPEN RIGHT DOORpage 252
HORIZONTAL TRANS JAM
OPEN FRONT COVER
UP SCANNER UNITpage 270
OUTPUT JAM
OPEN FRONT COVER
UP SCANNER UNITpage 270
SWITCH BACK JAM
OPEN FRONT COVER
UP SCANNER UNITpage 268
ORIGINAL DOC. JAM
OPEN DOC.FEED COVERpage 261 Media Misfeed Message Page Reference
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds 253
2Carefully pull out the misfed 
media.
CAUTION
The area around the fuser unit is 
extremely hot.
Touching anything other than the 
indicated levers may result in 
burns. If you get burned, 
immediately cool the skin under 
cold water, and then seek 
professional medical attention.
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds 254
Note
Decreased print quality may 
result if the surface of the image 
transfer belt or the transfer roller 
is touched.
Be careful not to touch the 
surface of the image transfer belt 
or transfer roller. 
3Close the right door.
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds 255
Clearing a Media Misfeed in Tray 2
1Pull the lever, and then open the 
right door.
Before opening the right 
door, fold up Tray 1.
2Carefully pull out the misfed 
media.
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing Media Misfeeds 256
CAUTION
The area around the fuser unit is 
extremely hot.
Touching anything other than the 
indicated levers may result in 
burns. If you get burned, 
immediately cool the skin under 
cold water, and then seek 
professional medical attention.
Note
Decreased print quality may 
result if the surface of the image 
transfer belt or the transfer roller 
is touched.
Be careful not to touch the 
surface of the image transfer belt 
or transfer roller. 
Downloaded From ManualsPrinter.com Manuals