Canon Lbp 5200 User Guide

							Printing from the Multi-purpose Tray2-22
Loading and Collecting Paper
2
6Select [Print] from the [File] menu in the application. Select 
the name of this printer from the [Name] or [Printer Name] 
field and click [Properties].
The Properties dialog box for the printer is displayed.
7Display the [Page Setup] sheet, then set the [Page Size] field 
to the size of the document that you created in the 
application.
 
						

							Printing from the Multi-purpose Tray2-23
Loading and Collecting Paper
2
8Set the [Output Size] to the size of the paper loaded in the tray 
as needed.
Select [A4] or [Letter] when printing transparencies.
Leave this field set to [Match Page Size] when the document page size and the 
size of the paper loaded in the multi-purpose tray are the same, since there is no 
need to change the setting.
IMPORTANT
If the [Page Size] and [Output Size] settings are different, the printer automatically 
enlarges or reduces the printout.
 
						

							Printing from the Multi-purpose Tray2-24
Loading and Collecting Paper
2
9Display the [Paper Source] sheet and set the [Paper Source] 
setting to [Multi-purpose Tray].
If you change the [Paper Selection] setting to a value other than [Same Paper for 
All Pages], even though the [Paper Source] field will be replaced by [First Page], 
[Other Pages], and other fields, these are all configured in the same way as the 
[Paper Source] setting.
NOTE
When the optional 250-sheet paper feeder is installed you can interleave paper 
sheets between transparencies by setting the [Paper Selection] field to 
[Transparency Interleaving].
 
						

							Printing from the Multi-purpose Tray2-25
Loading and Collecting Paper
2
10Change the [Paper Type] setting to match the type of paper 
loaded in the paper tray.
Set this to [Plain Paper] for regular paper, [Heavy Paper] for thick paper and 
cardboard, and to [Transparencies] for transparencies.
11Click the [OK] button to close the Properties dialog box.
 
						

							Printing from the Multi-purpose Tray2-26
Loading and Collecting Paper
2
12Click the [OK] button to start printing.
Printing Envelopes
Perform the following procedure to load envelopes in the multi-purpose tray.
IMPORTANT
•The envelopes that can be used with this printer are as follows:
•The following envelopes cannot be used with this printer. Using any of these envelopes 
may result in paper jams that are difficult to clear or may cause damage to the printer.
-Envelopes with fasteners or snaps
-Envelopes with address windows
-Envelopes with adhesive on the surface
-Wrinkled or creased envelopes
Envelope DL(110.0 mm x 220.0 mm)
Envelope COM10(105.0 mm x 241.0 mm)Envelope C5(162.0 mm x 229.0 mm)
Envelope Monarch(98.0 mm x 191.0 mm)Envelope B5(176.0 mm x 250.0 mm)
*You cannot use envelopes (Envelope DL, Envelope COM10, Envelope Monarch, 
Envelope C5) that have a flap on the short edge.
 
						

							Printing from the Multi-purpose Tray2-27
Loading and Collecting Paper
2
-Poorly manufactured envelopes in which the glued parts are uneven
-Irregularly-shaped envelopes
•Before loading the envelopes, flatten the stack of envelopes to release any remaining air, 
and press the fold lines along the edges tight.
•Do not print on the reverse side (glued side) of envelopes.
•The printing speed drops when printing envelopes.
NOTE
Printing on envelopes may produce wrinkles in the envelopes.
1Open the multi-purpose tray and pull out the auxiliary tray.
Refer to Opening the Multi-Purpose Tray, on p. 2-16 for instructions on opening 
the multi-purpose tray.
2Push the paper guides out a little wider than the actual width 
of the envelopes.
3Place the stack of envelopes on a flat surface and push on the 
top surface to clear out any trapped air, then push down firmly 
along the folded edges to flatten the envelopes.
 
						

							Printing from the Multi-purpose Tray2-28
Loading and Collecting Paper
2
CAUTION
When loading envelopes, be careful not to cut your hands with the edges 
of the envelopes.
4Loosen any stiff corners of the envelopes and flatten curls as 
shown in the figure.
5Align the edges of the envelopes on a flat surface.
 
						

							Printing from the Multi-purpose Tray2-29
Loading and Collecting Paper
2
6Load the stack of envelopes with the flaps closed and on the 
left side, and the address side facing up. Gently insert the 
stack until it touches the back of the multi-purpose tray as 
shown in the figure.
Be sure that the stack of envelopes passes beneath the paper limit guides.
CAUTION
When loading envelopes, be careful not to cut your hands with the edges 
of the envelopes.
IMPORTANT
•Up to 10 envelopes can be loaded at a time.
•Check that there is sufficient clear space between the paper limit guides and the 
envelopes. If there is no free space, take out a few of the envelopes.
•You cannot print on the reverse side (glued side) of envelopes.
•Load the envelopes so that the flaps are on the left side.
Paper Limit guide
 
						

							Printing from the Multi-purpose Tray2-30
Loading and Collecting Paper
2
•When printing to Envelope B5, load the envelopes with the flaps closed and the 
top edge facing into the printer.
7Adjust the paper guides to meet both sides of the stack.
IMPORTANT
•Although you should not leave any space between the paper guides and the 
envelopes, do not push the paper guides so strongly that the envelopes buckle. If 
the paper guides are too loose or too tight, the envelopes will not feed properly and 
this will cause paper jams.
•Do not touch the envelopes in the multi-purpose tray or pull them out during 
printing as this may cause printer errors.
You are now ready to configure the printer driver settings.
 
						

							Printing from the Multi-purpose Tray2-31
Loading and Collecting Paper
2
8Select [Print] from the [File] menu in the application. Select 
the name of this printer from the [Name] or [Printer Name] 
field and click [Properties].
The Properties dialog box for the printer is displayed.
9Display the [Page Setup] sheet, then set the [Page Size] field 
to the size of the document that you created in the 
application.