Canon Lbp 5200 User Guide

							Installing the 250-sheet Paper Feeder6-6
Optional Accessories
6
1Press the power switch to turn the printer off aa a a, remove the 
USB cable 
bb b b, and disconnect the power plug from the power 
outlet 
cc c c.
2Remove all the interface cables and the power cord from the 
printer.
3Move the printer from the installation site.
Hold the grips located on both sides of the printer securely with both hands.
CAUTION
•This printer weighs approximately 22.7 kg (Main Unit: Approx. 17 kg; 4 x 
Toner Cartridge: Approx. 3.2 kg; Drum Cartridge: Approx. 2.5 kg). Take care 
to carry the printer without hurting your back.
a
bc
 
						

							Installing the 250-sheet Paper Feeder6-7
Optional Accessories
6
•Never hold the printer by the front panel, ventilation slots, rear panel, or 
anywhere else other than the grips for moving the printer. Doing so may 
cause the printer to fall, resulting in personal injury.
•The rear side of the printer is the heavy side. When lifting the printer, take 
care not to lose your balance. Doing so may cause the printer to fall, 
resulting in personal injury.
4Carry the paper feeder to the installation site.
When carrying the paper feeder, hold the grips on both sides as shown in the 
figure.
The Rear End 
is Heavy
 
						

							Installing the 250-sheet Paper Feeder6-8
Optional Accessories
6
5Pull out the paper cassette from the paper feeder.
6Remove the tape that is securing the rear paper guide.
7Push down the paper cassette plate aa a a and remove the 
packing material by rotating it to the left 
bb b b.
a
b
 
						

							Installing the 250-sheet Paper Feeder6-9
Optional Accessories
6
8Insert the paper cassette into the paper feeder.
9Put the printer down slowly on the paper feeder.
Align the printer so that the grips on the printer match the pockets on the paper 
feeder.
CAUTION
Put the printer down slowly and carefully on the paper feeder. You may be 
injured if your hands, etc. are pinched by the printer.
10Connect the interface cables except for the USB cable, and 
connect the power cord.
11Plug the power plug into the AC power outlet.
Grips for Moving
Pockets
 
						

							Installing the 250-sheet Paper Feeder6-10
Optional Accessories
6
12Connect the USB cable.
IMPORTANT
•Refer to Printing from the Paper Cassette, on p. 2-34 for information on loading 
paper.
•When loading paper for the first time after installing the paper feeder, be sure to 
turn the printer on at least once before loading the paper.
Removing the 250-sheet Paper Feeder
Remove the paper feeder using the following procedure.
WARNING
Make sure you turn the printer off, disconnect the power plug and remove all 
interface cables and the power cord from the printer before removing the 
250-sheet paper feeder. If you remove the paper feeder without unplugging the 
cables, the electrical cord and interface cables may be damaged, causing a fire 
or electrical shock.
IMPORTANT
Remove the paper feeder when you are going to move or repair the printer.
1Press the power switch to turn the printer off, remove the USB 
cable, and disconnect the power plug from the power outlet.
2Remove all the interface cables and the power cord from the 
printer.
3Lift the printer and remove it from the paper feeder.
4Move the paper feeder.
5Move the main unit back to the installation site.
6Connect the interface cables except for the USB cable, and 
connect the power cord.
 
						

							Installing the 250-sheet Paper Feeder6-11
Optional Accessories
6
7Plug the power plug into the AC power outlet.
8Connect the USB cable.
 
						

							Installing the Network Board (AXIS 1611)6-12
Optional Accessories
6
Installing the Network Board (AXIS 1611)
Installing the optional network board (AXIS 1611) allows you to use the LBP5200 
directly over a network.
For more details on the AXIS 1611, visit the Axis Communications website (http://
www.axis.com/).
: TCP/IP : NetBIOS/NetBEUI
: TCP/IP : NetBIOS/NetBEUI
: Protocols you can use
Client(Windows 98/Me/2000/XP/Server 2003)
Client(Windows 98/Me/2000/XP/Server 2003)
Print Server(Windows 98/Me/2000/XP/Server 2003*)
Client(Windows 98/Me/2000)
Client(Windows XP/Server 2003)
If the computers connect directly to the network board
If the computers connect via a print server
LBP5200(with AXIS 1611 installed)
LBP5200(with AXIS 1611 installed)
*If the print server is running Windows XP/Server 2003, you cannot use the NetBIOS/NetBEUI protocol 
between the print server and printer.
 
						

							Installing the Network Board (AXIS 1611)6-13
Optional Accessories
6
Verifying the Contents of the Package
Before installing the network board, make sure that all of the following items are 
present in the package. In the rare event that any components are missing or 
damaged, contact the store where you purchased the board.
NOTE
A LAN cable is not supplied with the network board. If you are installing the network 
board to connect the printer to a network, you will need a category 5 twisted pair cable. 
Cables, hubs, etc. should be obtained separately as required.
Parts and Their Functions
aa a a
Printer Connector
This is the connector that plugs into the printer. Do 
not touch the connector with your fingers.
bb b b
LAN Connector
Connects to a 10BASE-T/100BASE-TX LAN cable.
cc c c
Status Lamp
Shows the status of the network board. If the lamp 
flashes when the LAN cable is not connected, the 
network board is malfunctioning.
dd d d
Power Lamp
This light turns on when the printer is on. If this lamp 
does not come on when the printer is turned on, the 
network board is malfunctioning.
ee e e
MAC Address Label
Displays the MAC address of this network board.
Network Board
(AXIS 1611)AXIS 1611
Users Manual
ae
dcb
 
						

							Installing the Network Board (AXIS 1611)6-14
Optional Accessories
6
Installing the Network Board
Use the following procedure to install the network board in the expansion board slot 
at the rear of the printer.
CAUTION
•Make sure that the printer is turned off and that all interface cables and power 
cord are disconnected from the printer before installing the network board. 
Attempting to install the board with the power on may result in electrical shock.
•Take care when you are handling the network board. Do not touch the corners or 
sharp areas of the network board as may cause personal injury.
IMPORTANT
The network board contains components that are sensitive to static electricity. To avoid 
damaging the board due to static electricity, observe the following handling precautions.
-Touch a metal object to dissipate static electricity before handling the network board.
-When handling the network board, do not touch anything that generates static 
electricity such as the computer display.
-Do not touch any of the components, printed wiring, or connectors on the network 
board.
-To avoid the effects of static electricity, do not remove the network board from the 
protective bag until immediately before you install it. The protective bag is also needed 
when you remove the network board. Store the protective bag and do not discard of it.
NOTE
You will need a Philips-head screwdriver to install the network board. Prepare a 
screwdriver in advance that matches the size of the screws.
 
						

							Installing the Network Board (AXIS 1611)6-15
Optional Accessories
6
1Press the power switch to turn the printer off aa a a
, remove the 
USB cable bb b b
, and disconnect the power plug from the power 
outlet cc c c
.
2Remove all the interface cables and the power cord from the 
printer.
If there is not enough space to install the network board, move the printer to a 
place where it is easier to work.
3Remove the 2 screws from the top and bottom sections of the 
expansion board slot, and then remove the protective plate.
IMPORTANT
You will need the screws that you removed to attach the network board. You will 
also need the protective plate if you remove the network board. Store these parts 
and do not discard them.
a
bc