Xerox Phaser 6115MFP User Manual

							Fax Regulations
Phaser® 6115MFP Multifunction Product
1-13 The Ringer Equivalence Number (REN) is used to determine the number of devices that may 
be connected to a telephone line. Excessive RENs on a telephone line may result in the devices 
not ringing in response to an incoming call. In most but not all areas, the sum of RENs should 
not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as 
determined by the total RENs, contact the local Telephone Company. For products approved 
after July 23, 2001, the REN for this product is part of the product identifier that has the format 
US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point 
(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. 
If this Xerox equipment causes harm to the telephone network, the Telephone Company will 
notify you in advance that temporary discontinuance of service may be required. But if 
advance notice is not practical, the Telephone Company will notify the customer as soon as 
possible. Also, you will be advised of your right to file a complaint with the FCC if you 
believe it is necessary. 
The Telephone Company may make changes in its facilities, equipment, operations or 
procedures that could affect the operation of the equipment. If this happens, the Telephone 
Company will provide advance notice in order for you to make necessary modifications to 
maintain uninterrupted service.
If trouble is experienced with this Xerox equipment, for repair or warranty information, please 
contact the appropriate service center; details of which are displayed either on the machine or 
contained within the User Guide. If the equipment is causing harm to the telephone network, 
the Telephone Company may request that you disconnect the equipment until the problem is 
resolved.
Repairs to the machine should be made only by a Xerox Service Representative or an 
authorized Xerox Service provider. This applies at any time during or after the service 
warranty period. If unauthorized repair is performed, the remainder of the warranty period is 
null and void. This equipment must not be used on party lines. Connection to party line service 
is subject to state tariffs. Contact the state public utility commission, public service 
commission or corporation commission for information.
If your office has specially wired alarm equipment connected to the telephone line, make sure 
that the installation of this Xerox equipment does not disable your alarm equipment. 
If you have questions about what will disable alarm equipment, consult your Telephone 
Company or a qualified installer.
Downloaded From ManualsPrinter.com Manuals 
						

							Fax Regulations
Phaser® 6115MFP Multifunction Product
1-14
Canada
Note:The Industry Canada label identifies certified equipment. This certification means that 
the equipment meets certain telecommunications network protective, operational and safety 
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements 
document(s). The Department does not guarantee the equipment will operate to the user’s 
satisfaction. 
Before installing this equipment, users must make sure that it is permissible to be connected to 
the facilities of the local telecommunications company. The equipment must also be installed 
using an acceptable method of connection. The customer should be aware that compliance 
with the above conditions may not prevent degradation of service in some situations. 
Repairs to certified equipment should be coordinated by a representative designated by the 
supplier. Any repairs or alterations made by the user to this equipment, or equipment 
malfunctions, may give the telecommunications company cause to request the user to 
disconnect the equipment. 
Users should make sure for their own protection that the electrical ground connections of the 
power utility, telephone lines and internal metallic water pipe systems, if present, are 
connected together. This precaution may be particularly important in rural areas. 
Caution:Users should not attempt to make such connections themselves, but should contact 
the appropriate electric inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an 
indication of the maximum number of terminals allowed to be connected to a telephone 
interface. The termination on an interface may consist of any combination of devices subject 
only to the requirement that the sum of the Ringer Equivalent Numbers of all of the devices 
does not exceed 5. For the Canadian REN value, please see the label on the equipment.
Downloaded From ManualsPrinter.com Manuals 
						

							Fax Regulations
Phaser® 6115MFP Multifunction Product
1-15
Europe
Radio Equipment & Telecommunications Terminal Equipment Directive 
The Facsimile has been approved in accordance with the Council Decision 1999/5/EC for pan-
European single terminal connection to the public switched telephone network (PSTN). 
However, due to differences between the individual PSTNs provided in different countries, the 
approval does not, of itself, give an unconditional assurance of successful operation on every 
PSTN network terminal point. 
In the event of a problem you should contact your authorized local dealer in the first instance.
This product has been tested to and is compliant with ES 203 021-1, -2, -3, a specification for 
terminal equipment for use on analogue-switched telephone networks in the European 
Economic Area. This product provides an user-adjustable setting of the country code. Refer to 
the customer documentation for this procedure. Country codes should be set prior to 
connecting this product to the network. 
Note:Although this product can use either loop disconnect (pulse) or DTMF (tone) signaling, 
it is recommended that it is set to use DTMF signaling. DTMF signaling provides reliable and 
faster call setup. Modification of this product, connection to external control software or to 
external control apparatus not authorized by Xerox, will invalidate its certification.
Downloaded From ManualsPrinter.com Manuals 
						

							Fax Regulations
Phaser® 6115MFP Multifunction Product
1-16
New Zealand Telecom Warning Notice
1.The grant of a Telepermit for any item of terminal equipment indicates only that Telecom 
has accepted that the item complies with minimum conditions for connection to its 
network. It indicates no endorsement of the product by Telecom, nor does it provide any 
sort of warranty. Above all, it provides no assurance that any item will work correctly in 
all respects with another item of Telepermitted equipment of a different make or model, 
nor does it imply that any product is compatible with all of Telecom’s network services.
The equipment may not be capable of correct operation at the higher data speeds 
designated. 33.6 kbps and 56 kbps connections are likely to be restricted to lower bit rates 
when connected to some PSTN implementations. Telecom will accept no responsibility 
should difficulties arise in such circumstances.
2.Immediately disconnect this equipment should it become physically damaged, and arrange 
for its disposal or repair.
3.This modem shall not be used in any manner which could constitute a nuisance to other 
Telecom customers.
4.This device is equipped with pulse dialing, while the Telecom standard is DTMF tone 
dialing. There is no guarantee that Telecom lines will always continue to support pulse 
dialing.
Use of pulse dialing, when this equipment is connected to the same line as other 
equipment, may give rise to bell tinkle or noise and may also cause a false answer 
condition. Should such problems occur, the user should NOT contact the Telecom Faults 
Service.
The preferred method of dialing is to use DTMF tones, as this is faster than pulse 
(decadic) dialing and is readily available on almost all New Zealand telephone exchanges.
5.Warning Notice: No 111 or other calls can be made from this device during a mains 
power failure.
6.This equipment may not provide for the effective hand-over of a call to another device 
connected to the same line.
7.Some parameters required for compliance with Telecom’s Telepermit requirements are 
dependent on the equipment (PC) associated with this device. The associated equipment 
shall be set to operate within the following limits for compliance with Telecom’s 
Specifications:
For repeat calls to the same number:
■There shall be no more than 10 call attempts to the same number within any 30 minute 
period for any single manual call initiation, and
■The equipment shall go on-hook for a period of not less than 30 seconds between the 
end of one attempt and the beginning of the next attempt.
For automatic calls to different numbers:
■The equipment shall be set to ensure that automatic calls to different numbers are 
spaced such that there is no less than 5 seconds between the end of one call attempt 
and the beginning of another.
8.For correct operation, total of the RN’s of all devices connected to a single line at any time 
should not exceed 5.
Downloaded From ManualsPrinter.com Manuals 
						

							Product Specifications
Phaser® 6115MFP Multifunction Product
1-17
Product Specifications
Physical Specifications
Base Unit
■Width: 528 mm (20.8 in.)
■Depth: 475 mm (18.7 in.)
■Height: 531 mm (20.9 in.)
■Weight: 33 kg (72.8 lb.)
Optional Tray 2
Height: 117 mm (4.61 in.)
Clearance Requirements
Environmental Specifications
Temperature
■Storage: -20o to 40o C / -4o to 104o F
■Operating: 10o to 32o C / 50o to 90o F
Relative Humidity
■Storage: 15% to 80% (non-condensing)
■Operating: 15% to 80% (non-condensing)
6115-003
100mm
(3.9”)
100mm
(3.9”)528 mm (20.8”)
531 mm (20.9”)
233 mm
 (9.2”)
138mm
 (5.4”)
902 mm (35.5”)
768 mm (30.2”) 581 mm (22.9”)
187 mm
(7.4”)
100mm
(3.9”)
Downloaded From ManualsPrinter.com Manuals 
						

							Product Specifications
Phaser® 6115MFP Multifunction Product
1-18
Electrical Specifications
■110-127 VAC, 50-60 Hz 
■110-120 VAC, 50-60 Hz (US/Canada Only)
■220-240 VAC, 50-60 Hz
■ENERGY STAR qualified product. Default time to Energy Save: 30 minutes.
Performance Specifications
Resolution
Maximum Resolution: 2400 x 600 dpi
Print Speed
■Color: 5 ppm (duplex: 5 ppm)
■Monochrome: 20 ppm (duplex: 11 ppm)
Copy Speed
■Color: 5 cpm (600 x 300 dpi)
■Black and White: 12 cpm (600 x 300 dpi)
Controller Specifications
RISC CPU (48 MHz) processor
Memory
■128 MB (SDRAM)
Interfaces
■Ethernet 10/100 Base Tx
■Universal Serial Bus (USB 2.0)
Downloaded From ManualsPrinter.com Manuals 
						

							Material Safety Data Sheet
Phaser® 6115MFP Multifunction Product
1-19
Material Safety Data Sheet
For Material Safety Data information regarding your Phaser 6115MFP product, go to:
■United States and Canada: www.xerox.com/msds
■European Union: www.xerox.com/environment_europe
For the Customer Support Center phone numbers, go to www.xerox.com/office/contacts. 
Downloaded From ManualsPrinter.com Manuals 
						

							Product Recycling and Disposal
Phaser® 6115MFP Multifunction Product
1-20
Product Recycling and Disposal
All Countries
If you are managing the disposal of your Xerox product, please note that the product may 
contain, lead, mercury, perchlorate, and other materials whose disposal may be regulated due 
to environmental considerations. The presence of lead, mercury, and perchlorate is fully 
consistent with regulations applicable at the time that the product was placed on the market. 
For disposal information, contact your local authorities. Perchlorate Material - This product 
may contain one or more Perchlorate-containing devices, such as batteries. Special handling 
may apply, please see www.dtsc.ca.gov/hazardouswaste/perchlorate
.
European Union
Some equipment may be used in both a domestic/household and a professional/business 
application.
Domestic/Household Environment
In accordance with European legislation, end of life electrical and electronic equipment 
subject to disposal must be segregated from household waste.
Private households within EU member states may return used electrical and electronic 
equipment to designated collection facilities free of charge. Please contact your local disposal 
authority for information.
In some member states, when you purchase new equipment, your local retailer may be 
required to take back your old equipment free of charge. Please ask you retailer for 
information.Application of this symbol on your equipment is confirmation that you 
should not dispose of the equipment in the normal household waste stream.
Downloaded From ManualsPrinter.com Manuals 
						

							Product Recycling and Disposal
Phaser® 6115MFP Multifunction Product
1-21
Professional/Business Environment
In accordance with European legislation, end of life electrical and electronic equipment 
subject to disposal must be managed within agreed procedures.
Prior to disposal, please contact your local reseller or Xerox representative for end of life 
takeback information.
North America
Xerox operates an equipment takeback and reuse/recycle program. Contact your Xerox sales 
representative (1-800-ASK-XEROX) to determine whether this Xerox product is part of the 
program. For more information about Xerox environmental programs, visit 
www.xerox.com/environment.html
 or for recycling and disposal information, contact your 
local authorities.
In the United States, you may also refer to the Electronic Industries Alliance website at 
www.eiae.org
.
Other Countries
Please contact your local waste authorities and request disposal guidance. Application of this symbol on your equipment is confirmation that you must 
dispose of this equipment in compliance with agreed national procedures.
Downloaded From ManualsPrinter.com Manuals 
						

							Phaser® 6115MFP Multifunction Product
2-1 This chapter includes:
■Product Tour on page 2-2
■Product Configurations on page 2-4
■Print and Scan Drivers on page 2-6
■Control Panel on page 2-7
■More Information on page 2-18
Product Features
Downloaded From ManualsPrinter.com Manuals