Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

							Infinite 4096 Hybrid Eey Telephone System INFATTE4096COMPONENT LIST 
/ 
1 
1 
I 
1 
1 
L 
1 
APPENDIX B 
mllV=F’mTE 4096 COMPONENT LIST 
Appendix El &jMte 4096 Component List 
4096 Basic Key Service Unit (KSUI 
4096 Central Processor Board (CPB) 
DC/DC Converter (DCUj 
Key Station Interface Board (KIB) 
Central Office Interface Board (COB) 
Arnpmed Central Of&e Board 
(COA) 
Power Supply Unit (PS) 
External Power Supply Housing (EPS) 
Enhanced Key Telephone 
Executtve Key Telephone 
Expansion Key Service Unit (EKSU) 
Direct Station/Line Selector (DSS/DLS) 
Phone Box 
RS232C Module (RSM) 
Battery Charging Card (BC) 
Power Failure Transfer Unit (PFn 
Applications Board (APL) 
Off-Premise &tension Board (OPXI 
Single Line Telephone Interface Board (SIB) 
Key Station Interface Board 
w/OHVA (KSB/OHV) 
Single Line Ring Generator (RG) 
Single Line DTMFRS Unit (SLU’) 
4096 Desc. Lnstall, and Oper Manual 
4096 Station Users Guide 
4096 Attendant Users Guide 
4096 SLT Users Guide 
CT Ran Connector Cable 
9EC Messenger 212 Plus Ran Device 
irfintte Wall Mount Kit 
Infinite Replacement Handset Cord 
Infinite Blank Designation Tabs 
$096 DSS/DLS Numbered Designation Tabs 
2OVCSOO3 
23vCsOo1 
2 1vCsOo3 
23vCSOo7 
23vCsO10 
23VCsOll 
2 lVCSOO2 
2 1vCs00 1 
1 ovCS200 
10vCs202 
2OVCSOO4 
17vCsoo 1 
26VCsoo2 
23vCSO14 
22VCSOO4 
23vcso 15 
23vcso 12 
2 lVCSOO4 
23vcsoo9 
23VCSOO8 
~21VCSOO5 
23vcso 13 
oovCs202 
oovCS2 13 
oovCS2 15 
oovCS2 14 
98ACT462 
1 GVCSOO 1 
18VCSOO 1 
OOVCS205 
00vcs209 
Issue 1, January 1992 
Appendix B-l  
						

							AECThe 
Description APPENDIX C 
Messengerm 212 Plus 
AEc’s ‘Ihe Messenger 212 Plus. Dual-Line 
Announcer can be used to provide the Re- 
corded Announcement feature of the Zr@i& 
4096 Uniform Call Distribution feature (UCD) 
that provides unanswered incoming CO Calls 
or calls in queue with a recorded message 
while waiting for an available UCD station. 
The In$ni& 4096 systems provide a program- 
mable option that allows the use of unused 
CO line positions. SLT ports as the specified 
RAN output port(s) or the APL RAN port. Each 
UCD group may be programmed to connect a 
waiting caller to either the list or second RAN 
port for the initial message, then select the 
other RAN port, if connected, for the second 
and subsequent messages. 
Installation 
The Messenger 2 12 Plus can be connected to 
the 
I- 4096 in the following configura- 
tiOXL‘3. 
- One or Two SLT ports. 
- One or Two CO line ports. 
- The APL RAN port and if needed one 
CO line port. 
The connection of each type of port requires 
different installation practices and will be de- 
scribed separately. 
SLT Ports 
To install the 2 12 Plus using one or two SLT 
ports the following equipment is required and 
must be installed for proper operation. 
- An SLT board with available ports. 
(23vcsoo9) 
- One APL Board. (23VCSO 12) 
- One RG/MW power supply 
(2 lvCsoo5) 
- One or two modular jacks (4 or 6 pin). When connecting the Messenger 2 12 Plus 
using one or two SLT ports the following op- 
tions on the 212 Plus unit must be set: 
1. Set the switches on the back of the unit 
as follows; 
Sl - off 
s2 - off 
s3 - off 
s4 - off 
2. The internal jumper plug of the Messen- 
ger 212 Plus should be in its default line 
type setting of CO/PBX. This will match 
the SLT port(s) of the system and provide 
ring mp for the start of the message. 
NOTE: When the jumper plug of the 
Messenger 212 Plus is set to CO/PBX 
for the line type then both lines of the 
Messenger must be connected to SLT 
ports of the system. 
3. Connect the Voice Tip and Voice Ring 
from the *J” connector of the SLT port 
being used to a modularjack. Using the 
line cords provided plug in to the modu- 
lar jack and one of the Line jacks in the 
back of the Messenger 2 12 Plus unit 
(See flgure 1) 
APL RAN and CO Line Ports 
For connection of the Messenger to either the 
APL RAN Port or to a CO line Port the Messen- 
ger 212 Plus must be configured as follows. 
1. Set the switches on the back of the 
Messenger 212 Plus unit as follows; 
Sl - off 
s2 - off 
s3 - off 
s4 - on 
Issue 1. January 1992 Appendix C-l  
						

							AEC The Messenger= 2 12 Plus hfiite 4096 Hybrid Eey Telephone System 
F’i@m Cl SLT to AEC Connectiona 
2. The internal jumper plug of the Messen- 
ger 212 Plus unit should be set to the 
first altematlve setting for a 600 ohm 
transformer coupled audio output. 
Check the Messenger 2 12 Plus Owners 
Manual for procedures on changing the 
internal jumper plug. 
NOTE: Using the 600 ohm setting of 
the Messenger 2 12 Plus both lines of 
the Messenger must be connected to 
any combination of the APL RAN out- 
put port or one or two CO line port(s). 
When installfng the Messenger 212 Plus unit 
onto the 4096 System, both the APL RAN 
output port and a CO Line port can be used 
simultaneously. However connection of the 
Messenger to these ports is different For this 
reason each type. of installation will be de- 
scribed separately. 
APL RAN Port 
When the Messenger 2 12 Plus unit is installed 
using the APL RAN port the following equip- 
ment will be required. 
- An AF’L Board (23VCSO12) 
- An Am 8 position to 6 position 
modular line cord. (98ACT462) 1. To connect the Messenger 2 12 Plus to the 
APL RAN jack plug the 6 position end of 
the ACT modular line cord into the APL 
RAN Port (APL MOD 3 jackl then plug the 
8 position end of the line cord into the 
line 1 or line 2 position on the back of 
the Messenger 2 12 Plus unit. 
If an ACT 8 position to 6 position cord is not 
available use the wiring diagram in f3gure 2 as 
a guide to connect the Messenger 2 12 Plus 
unit to the APL RAN port, 
CO Line as a RAN Port 
To Install the Messenger 2 12 Plus using a CO 
Line port as the R4N output port the following 
equipment is necessary for a proper installa- 
tion. 
- Unused CO line ports on a, COB or 
COA Board. (23VCSO 10 or 
23VCSO 11) 
- Power Fail Transfer unit (23VCSOlS) 
with Loud Bell Control for each CO 
port to be used. 
- 24 volt DC power supply to provide a 
fflteredtalkpa,thIlessthan 1 ampis 
required). 
- Two (2) 300 ohm l/4 watt resistors 
for each circuit. 
- One or two 8 conductor modular 
jacks and 8 conductor line cords. 
Appendix C2 Issue 1, January 1992  
						

							Injinite 4096 Hybrid Key Telephone System AEC The Messengerm 212 Plus 
APL 
RAN Jade 
PklX 
STOP 1 
START 2 
VOICE 3 
VOICE 4 
START 5 212 Plus 
Line Jack 
PinX 
1 STOP 
2 STOP 
D 3 
4 VOICE 
5 VOICE 
b 
6 
STOP 6 7 GROUND 
8 START 
Fi@1reG2 ACTSCond.to6Cond.RANLheCord 
To install the Messenger 2 12 Plus using a CO 
circuit as the interface connect as described 
below. (see figure 3) 
1. Connect the 300 ohm resistor ln series 
with the - (negattve) lead of the 24 volt 
DC power supply and the CO tip on the 
‘P” connector. Depending on the application the following 
program codes will need to be updated. 
a Universal Call Distribution (FLASH 19) It 
is necessary to specify which RAN table(s) 
will be used for each UCD group assigned. 
This is done by pressing button 12 while 
in UCD programming. 
2. Next connect the second 300 ohm resfs- 
tor in series to the + (positive) lead of the 
power supply and the 8 position modular 
connector pin 5 mp / green). 
3. Then wire the ring lead from the ‘Y 
connector of the CO port being used to 
pin 
4 of the 8 pin modular jack (Ring / 
red). 
4. Connect both of the LBC contact leads 
of the Power Fail Transfer unit to the 
START and GROUND leads of the 8 pin 
modular jack (pins 7 and 8). 
Connection of the Messenger 212 Plus to the 
system Ls now complete. Proceed wltb apply- 
ing power and recording your message(s) as 
described in the Messenger 2 12 Plus Owners 
manual. 
Programming 
It will be necessary to update the data base of 
the 4096 system to include the RAN 
opuons. 
b UCD Timers 0?LASH 33) The Ring timer 
(button 1) determines how long an Incom- 
ing CO call will ring into the UCD group 
before being answered and presented to 
the first message. 
The Message Interval Timer (Mll’J(button 
2) determines the duration of time the 
caller will be in queue and on hold be- 
tween messages 
The OVeRflow timer lbution 3) determines 
the total time, starting from when the call 
was answered, a caller will be kept in 
queue before being routed to the overflow 
station. 
c Announcement Tables (FLASH 34) This 
determines the type. index (port) number 
and length for the two available Recorded 
announcements (RAN). 
When defining SLT port(s) or CO Line 
port(s) as the RAN output port it is most 
important to set the TIME parameter 
(length of the message) in the An- 
Issue 1. January 1992 Appendix C-3  
						

							AEC The Messengean 212 Plus 
Finite 4096 Hybrid Key Telephone System 
nouncement Table so that it ls approxi- 
mately one second longer than the actual 
message. 
d WhenaCOlfnehastxenuseditwillbe 
necessaq to program an LBC contact to 
that particular line. This is accompkhed 
in Loud Bell Control assignments @WISH 
16). AssigntheCOporttobeusedforthe 
RAN operation to one of the LBC contacts. 
Refer to the Iry%ti& 4096 Description. Instal- 
lation and Operation manual for further in- 
structfons on how to enter the program mode 
and additional information on the above listed 
program options. Also reference The Messen- 
ger Owner’s Manual for recording, battery 
operation and troubleshooting information. 
‘p’ Bkck (66 Type) 
I AEC 
The Messenger 
212 Plus 
I _----- I Tmetds 
GROW0 
p---J LBC 
STAAT 
Appe*c- G-4 Issue 1, January 1992