Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

							OFF-HOOK CALL ANNOUNCE 
After reaching a station that is busy off-hook you may use Off- 
Hook Call Ahnounce. 
TO USE OFF-HOOK CALL ANNOUNCE 
1A) If you hear a singl’e ring Fne, speak to the called party. 
I 
. . . 
or . . 
1 B) If you hear a busy tone, dial 1. 
l You will hear a single ring tone. 
l Speak to the called party. 
PAGING 
TO PAGE 
1) 
Lift the handset. 
2) Listen for intercom dial tone and dial the following: 
11 1 :I Ctl$Froups 1 - 4) 
00 I G::uUp #2 
PI = Group #3 
IN = Group ##4 
pd = All Call (with External Page)* 
II = External Page 
3) Make your announcement in a normal voice level and repeat 
it. 
4) Hang up when you have completed your announcement. 
*Programmable Option; also see Call Pick-up. 
8 
TONE SIGNALLING 
PROGRAMMABLE OPTION 
TO MAKE A TONE SIGNAL CALL 
1) Call another station via intercom. 
l You will hear a ringing tone as the primary method of 
intercom call signalling (voice announcing is inopera- 
tive). 
2) Speak to the called party when the call is answered. 
3) To make a voice call, dial 0. 
TRUNK QUEUING 
This feature provides a means for station users to be placed in a 
waiting queue for a busy outgoing trunk group, and to be called 
back when a trunk in the group is available. 
TO USE TRUNK QUEUING 
1) Lift the handset. 
l You will hear intercom dial tone. 
2) Dial the desired trunk group access code: 
Code Line Group Code Line Group 
9 95 
91 96 
92 97 
93 98 
94 7XX Selective access 
to line number 
“Xx” 
3A) If there is an idle trunk, you will be connected. 
l You will hear CO dial tone. 
4A) Dial the desired telephone number. 
5A) Hang up when the call is completed. 
. . or . . . 
(continued)  
						

							. 
CALL TRANSFER WITH CAMP-ON 
This feature allows you to transfer an outside call to a station that 
is either idle or busy. 
TO TRANSFER A CALL 
1) While connected to an outside line, flash the hookswitch. 
l You will hear intercom dial tone. 
2) Dial the station number to which the call is to be transferred. 
3A) If the called station is idle: 
l You will hear a single ring tone. 
4A) Announce the call. 
5A) Hang up. 
. . . or . . . 
38) If the called station is busy: 
l You will hear busy tone. 
48) Hang up. 
l The call is camped-on to the busy station. 
NOTES: 
1. The Override features (See 0 VERRIDE) ma y be used instead 
of transfer camp-on. 
2. Flash the hookswitch to reconnect to the line before it is 
transferred (If the called station has lifted the handset or 
depressed them button, a conference will be formed b y the 
hookswitch flash.) 
3. The call willrecall you andcamp-on is cancefledif the station 
does not pick it up within a predetermined time. Inform the 
caller of the situation, andrepeat the procedure, if necessary. 
CONFERENCE CALLS 
TO CONFERENCE UP TO FOUR STATIONS ON ONE CO 
LINE 
1) Establish a standard one-CO line call. 
2) Flash the hookswitch. 
l You will hear intercom dial tone. 
l The existing call will be on hold. 
3) Dial the number of the desired station. 
4) Flash the hookswitch after the party answers.* 
l All parties will be conferenced. 
5) Repeat to add another station. (Four stations, including 
yours, and one CO line is maximum.) 
6) Hang up when the call is completed. 
TO CONFERENCE UP TO FOUR STATIONS ON INTERCOM 
1) Establish a standard two-station intercom call. 
2) Flash the hookswitch. 
l You will hear intercom dial tone. 
l The existing call will be on hold. 
3) Dial the number of the desired station. 
4) Flash the hookswitch after the party answers.* 
0 All parties will be conferenced. 
5) Repeat to add another station. (Four stations, including 
yours, is maximum.) 
6) Hang up when the tail is completed. 
* Calledparty must come off-hook or depress thembutton. If you 
receive a busy tone or no answer, return to the original connec- 
tion by flashing the hookswitch.  
						

							DOOR PHONE 
TO CALL/MONITOR A DOOR PHONE 
1) Lift the handset. 
l You will hear intercom dial tone. 
1) Dial the desired number: 
q c]c] D oor phone location __ 
q nu D oor phone location I_-- 
0 
q q Door phone location 
aon D oor phone location __ 
l You will not hear a warning tone. 
3) Hang up when the call is completed or when you no longer 
wish to monitor the door phone. 
INTERCOM CALLS 
TO MAKE AN INTERCOM CALL 
1) Lift the handset. 
l You will hear intercom dial tone. 
2) Dial the desired station number. 
. You will hear a single ring tone. 
3) Speak when the ring tone ends.” 
4) Hang up when the call is completed. 
*If you are calling another standard telephone, ring tones will 
continue. Wait for an answer. Tone signalling can be accomp- 
lished by dialing g after the station number. 
*TO RECEIVE AN INTERCOM CALL 
1) You will hear a ringing signal (1 second on - 3 seconds off). 
2) Lift the handset and speak to the caller. 
3) Hang up when the call is completed. 
pllllllllrTOSHlEW’7 
OUTSIDE CALLS 
TO MAKE AN OUTSIDE CALL 
1) Lift the handset. 
l You will hear intercom dial tone. 
2) Dial the CO line access code: 
Code Line Group Code 
Line Group 
9 95 
91 
96 ___ 
92 
97 
93 98 
94 7XX Selective access 
to line number 
“xx” 
3) Listen for CO dial tone. 
4) Dial the desired telephone number. 
5) Hang up when the call is completed. 
TO RECEIVE AN INCOMING CALL 
I: You will hear a ringing tone. 
2) Lift the handset. 
3) Hang up when the call is completed. 
OVERRIDE 
After reaching a busy station, you may signal that station that a 
call is waiting. 
TO INITIATE A BUSY OVERRIDE SIGNAL 
1) Dial@. 
l A tone signal will be heard at the busy station. 
After reaching a DND station, you may signal tha! station that a 
call is waiting. 
TO OVERRIDE DND (Programmable Option) 
‘I) Dial 1. I 
l A tone signal will be heat$l at the DND station, 
After reaching a busy station, ‘Executive Override allows you to 
enter an established conversation. 
TO INITIATE EXECUTIVE OVERRIDE (Programmable Option) 
1) Dialg. 
. A tone signal will be heard prior to entering the 
conversation. 
/’ 
,d 
6  
						

							TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM ’ STRATA Se/We 
SYSTEM RECORD 
MAY 1988 
- 
trata Se & 
RELEASE 2 
SYSTEM RECORD 
PART NUMBER: A-R SH S/VIER2 
ITEM NUMBER: 4010902  
						

							STRATA Se/Vie 
SYSTEM RECORD 
MAY 1988 
PROGRAM 01 -SYSTEM ASSIGNMENTS (Basic) 
X = Select (LED on) Initialized Data: All LEDs off 
PROGRAM O#l--DOOR PHONE SELECTION 
KEY/LED X LED ON LED OFF 
17 Door Lock Timeout (6 sec.) 3 sec. 
08 Door Phone 2B Door Lock Door Phone 
07 Door Phone 2C Busy-out No Busy Signal 
06 Door Phone 2B Busy-out 1 No Busy Signal 
05 
04 
03 
02 
01 
00 Station 12/l 4 Door Phone EKT 
Door Phone 1 C Alarm (Station 
13 only) Door Phone 
Door Phone 1 B Door Lock Door Phone 
Door Phone 1 C Busy-out No Busy Signal 
Door Phone 1 B Busy-out No Busy Signal 
Station 11 /13 Door Phone 
EKT 
X = Select (LED on) 
Initialized Data: All LEDs off 
Availability: 
Se= 
11,12 
Vle = 13, 14 
-l-  
						

							STRATA Se/We 
SYSTEM RECORD 
MAY 1988 
PROGRAM 0%SYSTEM ASSlGNMENTS(Options) 
X = Select (LED on) Initialized Data: All LEDs off *We on/y 
AMP CONF: TRK TO TRK: 
Se-l 6/l 7 Se-14,15 
We-1 8/l 9, 24/25 Vle-22, 23 
PROGRAM 0#2 
ACCOUNT CODE DIGIT LENGTH and MODEM SPEED 
KEY/LED X LED ON 
LED OFF 
17 Repeat Ringing 
Standard Ringing 
15 SDTU Modem Speed-1200 bps 
300 bps 
04 Account Code Digit Length 
03 Account Code Digit Length 
02 Account Code Digit Length 
01 Account Code Digit Length 
00 Account Code Digit Length 
X = Select (LED on) Initialized Data: LEDs 01 & 02 on; all other LEDs off. 
YO 
TE: 
LEDs 00 - 04 set the Account Code Digit Length (4 - 15 Digits) in binary format per the 
table below. 
SMDR ACCOUNT CODE 
DIGIT LENGTH TABLE 
Dish Length 1 4 1 5 1 6 17 18 1 9 110 111 112 113 114 115 1 
04 
Ix x x xlxlx 
03 
I 
x xl I I 
02 x x.x x 
x x 
01 x x x x 
b 
X = LEDs on All LEDs off = no data 
-2-  
						

							STRATA Se/Me 
SYSTEM RECORD 
MAY 1988 
X = Select (LED on) Initialized Data: LED 02 on; all other LEDs off 
*See Program 08 for group assignments. 
Only one station may be Message Center. 
PROGRAM 04-CO LINE OUTPULSING SELECTION 
KEY/LED X LED ON 
LED OFF 
06 DP 
DTMF 
05 DP 
DTMF 
initialized Data: Ail LEDs off 
KEY/LED 1 
PROGRAM #4-CO LlNE IDENTIFICATION 
16 DIGITS MAXIMUM  
						

							31IIHlH 3e/Vle 
SYSTEM RECORD 
MAY 1988 
AUT PROGRAM 05 
‘OMATIC RECALL FROM HOLD TIMING 
1 KEY/LED 1 X t TIME 1 
I 03 1 1 48 sec. 1 
X 5 Select (LED on) 
Initialized Data: LED 02, 10. 11 and 12 on 
PROGRAM 06 
AUTOMATIC RELEASE 
ON HOLD ENABLE 
X = Enable (LED on) 
Initialized Data: All LEDs off 
PROGRAM 07 
AUTOMATIC RELEASE 
ON HOLD TIMING 
X = Cross Bar (XB) Timing (95ms) 
Blank = ESS Timing (450ms) 
Initialized Data: All LEDs off 
PROGRAM 0#5 
CAMP-ON 
.  TIMEOUT 
KEY/LED 
X TIME 
03 64.sec. 
02 48 sec. 
01 32 sec. 
00 7% sec. 
X = Select (LED on) 
Initialized Data: LED 01 on 
PROGRAM 0#6 
TRUNK-to-TRUNK 
CONNECTION ENABLE 
X = Enable (LED on) 
Initialized Data: All LEDs 
Off 
PROGRAM 0#7 
lA2 INTERFACE 
X = Enable (LED on) 
Initialized Data: All LEDs off 
-4-  
						

							STRATA Se/Vie 
SYSTEM RECORD 
- MAY 1988 
PROGRAM 08 PROGRAM 0#8 
CO LlNE PICKUP  CO LlNE PICKUP NIGHT RING OVER 
GROUP  GROUP EXTERNAL PAGE (Vle only) 
X = Belongs to Group 2 
Blank = Belongs to Group 1 
Initialized Data: All LEDs off X=Ring(LEDon) Blank=Noring 
Initialized Data: All LEDs on 
PROGRAM 09 
SlNGLE CO LINE (DIAL 9) 
GROUP SELECTION (OPX, Trunk Queuing) 
X = Include in “Dial 9” group (LED on) 
Initialized Data: All LEDs on 
NOTE: 
Used only if LED 
15 is off in Program 01. 
PROGRAM 0#9 
OPL LINE HUNTING 
X = Hunt 
Initialized Data: All LEDS off 
PROGRAM 09X 
FOUR CO LINE GROUPS SELECTION 
(Dial 91, 92, 93, 94, 95, 96, 97, 98) 
I 
01 I 
I 
I 
I 
X = Include in group (LED on) 
Initialized Data: 091-All LEDs on 
092 - 098-All LEDs off 
NOTE. 
Used only if LED 15 is on in Program 01 
(Eight CO Line Groups). * VJe only 
Line groups 95 - 98 do not apply to Automatic Off-hook Selection.- -- --  
						

							3itlAIA be/Vie 
SYSTEM RECORD 
MAY 1988 
ES 1 1stD  PROGRAM 19X 
PBX ACCESS CODES 
1 #3(193) i 
#4 (194) 
#5 
(195) 
#6 (196) 
PROGRAM 190 
PBX BACKUP . 
X = Connected to PBX line (LED on) 
Enter the Access Codes (Maximum: 8) 
Initialized Data: None 
NOTE: 
If the access code is a single digit, enter ““‘in the 
second column. If all combinations foil0 wing a 
particular 1st digit are to be considered access 
codes (e.g., 91, 92, 93, ect.), enter “*‘* (don’t 
care) in the 2nd column. 
Initialized Data: All LEDs off 
PROGRAM loo--TOLL RESTRICTION SYSTEM PARAMETERS (Dialing Plan) 
KEY/LED X LED ON 
LED OFF 
02 1 + A/C f NXX and NXX 
01 1 tA/CtNXXandl tNXX 
00 A/C f NXX and 1 f NXX 
b 
X = Select (LED on) Initialized Data: LED 00 on 
NOTE: 
KEY/LED 03 and 04 are not used 
PROGRAM 101 
TOLL RESTRICTION 
OISABLE 
1 1 X 1  KEYi’ED PROGRAM 102 
FORCED ACCOUNT 
CODE CHECK 
X = Disable (LED on) 
Blank = Enable 
Initialized Data: All LEDs X=Check Blank=NoCheck 
Initialized Data: All LEDs off 
NOTE. 
Program 0#2 defines 
number of digits in account 
code.