Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 32 
PROGRAM 1XY 
TOLL RESTRICTION CLASS AREA CODE ENTRY 
(LCD TELEPHONE REQUIRED) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station 1’3/17. 
LCD is blank. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
LCD is blank. 
3) Dial flia (Allow), iJHa (Deny) or Pafl(Display) SPKR LED flashes continuously. 
as required. (X = Restriction class 1 - 4.) LCD displays dialed number. 
1 X 2 = LCD is blank. 
4) Press a key. 1 X 3 = LCD is blank. 
1 X 4 = LCD displays all allowed codes. 
5) Enter first area code in range sequence LCD displays code entered. 
(start). 
6) Depress p key.* LCD shifts left to provide space for next code. 
7) Enter final area code in range sequence LCD displays code entered. 
(stop).” 
8) Depress 1 key. LCD is blank. 
9) Return to Step 5 to enter additional area 
codes. 
10) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
11A) Return to Step 2 in order to continue with 
this program 
or 
11 B) Go to Step 2’in’another program table 
. . or . 
11 C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 6 and 7 if only one area code in sequence is being entered. 
-5%  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 33 
PROGRAM IX2 
TOLL RESTRICTION CLASS OFFICE CODE ENTRY 
(LCD TELEPHONE REQUIRED) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. .- 
Normal functions halt on station 13/17. 
LCD is blank. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
LCD is blank. 
3) Dial $lga (Allow), iaa(Deny) or aEja(Display) SPKR LED flashes continuously. 
as required. (X = Restriction class 1 - 4.) LCD displays dialed number. 
1 X 6 = LCD is blank. 
4) Press g key. 1 X 7 = LCD is blank. 
1 X 8 = LCD displays all allowed codes. 
5) Enter first office code in range sequence 
LCD displays code entered. 
(start). 
6) Depress 4 key.* LCD shifts left to provide space for next code. 
7) Enter final office code in range sequence LCD displays code entered. I 
(stop).” 
8) Depress /j key. LCD is blank. 
9) Return to Step 5 to enter additional office 
codes. 
10) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
11A) Return to Step 2 in order to continue with 
this program 
. . . or . . . 
11 B) Go to Step 2 in another program table 
. . . or . . . 
1 1 C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 6 and 7 if only one office code in sequence is being entered. 
-59-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 34 
PROGRAM 2XY 
TOLL RESTRICTION AREA/OFFICE CODE EXCEPTION TABLE . 
(LCD TELEPHONE REQUIRED) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13117 LED 19 on. 
System is in program mode. 
Normal functions halt on station f3/17. 
LCD is blank. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
LCD is blank. 
3) Dial aR0, (X = Table 1 - 8). LCD displays dialed number, then shifts left to pro- 
vide space for next entry (or displays current area 
code). 
4) Enter area code. 
5) Depress the m key. 
6) Depress the m key. LCD clears and displays area code entered. 
Binary data is shown on LEDs 00 - 03. 
LCD is blank. 
SPKR LED steady on. 
LCD is blank. 
7) Dial 114 (Allow), afli (Deny) or Qfla(Display) SPKR LED flashes continuously. 
as required. (X = Restriction class 1 - 8.) LCD displays dialed number. 
2 X 2 = LCD is blank. 
8) Press B key. 2 X 3 = LCD is blank. 
2 X 4 = LCD displays all allowed codes. 
9) Enter first office code in range sequence LCD displays code entered. 
(start). 
10) Depress 1 key.* LCD shifts left to provide space for next code. 
11) Enter final office code in range sequence LCD displays code entered. 
@top).* 
12) Depress i key. LCD is blank. 
13) Return to Step 5 to enter additional office 
codes. 
14) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
15A) Return to Step 2 in order to continue with 
this program 
or . . . 
15B) Go to Step 2’in’another program table 
. . . or . . . 
15C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
*Skip Steps 10 and I 1 if only one office code in sequence is being entered. 
-so-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
-JANUARY 1988 
TABLE 35 
PROGRAM 1X1 
TOLL RESTRICTION CLASS AREA/OFFICE CODE EXCEPTION TABLE SELECTION 
1 SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial pf3a on the dial pad. (X = Restriction class SPKR LED flashes continuously. 
1 - 4, as defined in Program 6xX.) The various LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the various keys, turn their associated be on. 
LEDs on or off, as required. The detailed If the LED is already on, depressing the associated 
meaning of each key/LED is shown below. key will turn it off and vice versa. LEDs may be 
NOTE: turned off and on until the desired pattern is set. 
68) Go to Step 2 in’anodthkr program table 
. . or. . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
-61-  
						

							PHUliHAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 36 
PROGRAM l#OO 
LEAST COST ROUTING HOME AREA CODE ENTRY 
(LCD EKT REQUIRED--STRATA Vie only) 
I . 
1 SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station**l7. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial 0 114 on the dial pad. SPKR LED flashes continuously. 
LCD: DATA = (indicates present data) 
4) Refer to the System Record Sheet. 
Using the dial pad, enter the system’s home 
area code. 
NOTE. 
To clear existing data without entering a 
new number, depress the a key once for 
LCD: (displays code entered) 
each digit. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-62-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 37 
PROGRAM 1 #OX 
LEAST COST ROUTING SPECIAL CODES 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. .- 
Normal functions halt on station 17. . 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial flaaa on the dial pad. X = 1 - 5 corre- SPKR LED flashes continuously. 
sponds to five different special codes that LCD: DATA = (indicates present data) 
may be entered. 
4) Refer to the System Record Sheet. LCD displays code entered. 
Using the dial pad, enter the special code 
number. 
5) Depress the cr;rr;l key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table * 
. . . or. . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-63-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 38 
PROGRAM 1#06 
LEAST COST ROUTING PARAMETERS 
(LCD EKT REQUIRED-STRATA Vie only) I 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station I?‘. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial pfli 1 on the dial pad. SPKR LED flashes continuously. 
LCD: (displays program number) 
Various LEDs indicate present data. 
4) Refer to the System Record Sheet. LCD displays code entered. 
Using keys 00 - 02, turn their associated 
LEDs ON or OFF, as required. 
5) Depress the w key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-64-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 39 
PROGRAM 1#07X 
SELECT LONG DISTANCE INFORMATION (LDI) ROUTE 
(LCD EKT REQUIRED-STRATA Vie only) 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 17. 
3) Dial flaBa on the dial pad. 
4) Refer to the System Record Sheet. 
Using the dial pad, enter X (X = 1 - 8, corre- 
sponding to one of eight route table 
numbers). 
5) Depress the m key to place new data in 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED on. 
Station 17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
SPKR LED steady on. 
LCD: PROGRAM’NO.? 
SPKR LED flashes continuously. 
LCD: DATA = 8 
LCD displays code entered. 
All station 17 LEDs (except 19) go off. 
SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored,previous data is erased. 
-65-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 40 - 
PROGRAM 1#08X 
SELECT LOCAL CALL ROUTE 
(LCD EKT REQUIRED-STRATA Vie only) _ 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 17. 
3) Dial iiafl on the dial pad. 
4) Refer to the System Record Sheet. 
Using the dial pad enter X. X = 1 - 8, corre- 
sponding to one of eight route table numbers. 
5) Depress the m key to place new data in 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
SPKR LED steady on. 
LCD: PROGRAM NO.?. 
SPKR LED flashes continuously. 
LCD: DATA = 8 
LCD displays code entered. 
All station 17 LEDs (except 19) go off. 
SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-66-  
						

							TABLE 41 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
PROGRAM I#09 
DIAL ZERO (0) TIMEOUT 
(LCD EKT REQUIRED-STRATA Vie only) 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 17. 
3) Dial flaii on the dial pad. 
4) Refer to the System Record Sheet. 
Using one key (00 - 03), turn its associated 
LED ON or OFF as required. 
NOTE: 
Only one LED may be on at a time. 
5) Depress the m;n;l key to place new data in 
memorv. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED on. 
Station 17 LED 19 on. 
System is in program mode. l *- 
Normal functions halt on station 17.. 
LCD: PROGRAM MODE 
SPKR LED steady on. 
LCD: PROGRAM- NO.? 
SPKR LED flashes continuously. 
LCD: (displays dialed number) 
An LED indicates present data. 
An X on the record sheet means the LED should 
be on. 
Only one LED is permitted to be on; depressing an- 
other key will turn that LED on and turn off the pre- 
vious LED. 
All station 17 LEDs (except 19) go off. 
- 
SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, orevious data is erased. 
-67-