Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

							PHUlitlAMMINti PHULtUUHtS 
SECTION 500-036-300 
JANUARY 1988 
TABLE 52 
PROGRAM 4#XX 
STATION FLEXIBLE KEY ASSIGNMENTS 
(IMPORTANT! LCD EKT HIGHLY RECOMMENDED) 
(Do Program 4XX for all stations before this program.) 
. 
SET LED on. 
1) Lock in the SE7 switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
Normal functions halt on station*t3/17. 
2) Depress the m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial 4flIaon the dial pad (XX = the number SPKR LED flashes continuously. 
of the station(s) to be programmed). 
4) Refer to the System Record Sheet. The feature currently assigned to the code number 
Depress the key to be programmed. 
for that key is displayed by the LCD (see table 
below). 
5) Dial in the new feature’s number. The mean- The new feature’s number is displayed on the LCD 
ing of each feature code is shown below. (see table below). 
6) Continue returning to Step 4 until all desired 
features for the chosen station(s) are pro- 
grammed. 
7) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
8A) Return to Step 2 in order to continue with 
this program 
88) Go to Step 2 in’an%$r program table 
or . . . 
8C) Transfer data into working memory per Pa- 
ragraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTES. 
1. For multiple station programming, refer to Paragraph 02.10. 
2. All codes can be assigned only once per EKT. If assigned more 
XX = Direct Station Selection (DSS) EKT distinction.- than 
once, keys become AD 
keys. 
I 
co2 1 G 
03 co3 1 81 
04 co4 1 1 
82 
05 co5 1 83 
Am ^^^ 
96 --i 
1 07 
Locked !SI Kev 
-78-  
						

							TABLE 53 
PROGRAM 5XX 
STATION CLASS OF SERVICE #I PROGRAMMING PROCEDURES 
SECTION 500-036-300 
_ JANUARY 1988 
1) Lock in the SET switch on the HKSU. 17 LED 19 on. 
Using the appropriate keys, turn their asso- 
ciated LEDs on or off, as required. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in’an”d,her program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
For multiple station programming, refer to Paragraph 02.10. 
-79-  
						

							PROGRAMMING PROCEOURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 54 
PROGRAM 5#XX 
STATION CLASS OF SERVICE #2 
1 SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
the associated 
key/LED is not shown, it is not used. 
6B) Go to Step 2 i,‘&“dtt&; program table 
. . . or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
NOTES: 
1. For multiple station programming, refer to Paragraph 02.10. 
2. If a station is programmed to automatically select a trunk group ($7 or 9 1 - &I), it wit/ select the 
last available line in that group unless a line in that group is ringing-it wi// select the ringing 
line. 
-8O-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
_ JANUARY 1988 
TABLE 55 
PROGRAM 6XX 
STATION TOLL RESTRICTION/LCR CLASSIFICATION 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED ‘I9 on. 
System is in program mode. 
.a- 
Normal functions halt on station 13/l 7. 
)P 
2 De ress the w 
3) Dial flgBon the dial pad (XX = the number of SPKR LED flashes continuously. 
the station(s) to be programmed). An LED indicates present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the various keys, turn an associated be on. 
LED on or off, as required. The detailed mean- Only one LED may be on; depressing another key 
ing of each key/LED is shown below. 
I will turn that LED on and turn off the previous LED. 
KEY/LED FEATURE 
LED ON LED OFF 
12 LCR Class 3 (Vie only) 
Selected None 
11 LCR Class 2 (Vle only) Selected , None 
10 LCR Class 1 (We only) 
Selected / None 
07 Digit-Free 
Selected / None 
06 Class 4* 
Selected / None 
05 Class 3” 
1 Selected None 
04 Class 2” I Selected 
None 
03 Class l* 
Selected None 
02 Restrict 0 or 1 as 1st and 2nd digit 
Selected None 
01 Allow 1 + Office Code only 1 Selected 
None 
00 No Restriction 
Selected - 
’ 5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memorv. 
6A) Return to Step 2 in order to continue with 
this program 
or . . . 
66) Go to Step 2 in another program table 
. . or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
*NOTES. 
1. For multiple station programming, refer to Paragraph 02.20. 
2. See Toil Restriction; 
Programs 100, 1 Xl, 1 XY, 1 X2, and 2XY. 
-81-  
						

							rtiUblwMMINLi PtiUbtUUntS 
SECTION 500-036-300 
JANUARY 1988 
TABLE 56 
PROGRAM 6#XX 
STATION-TO-STATION HUNTING 
1) Lock in the SET switch on the HKSU. 
ines the station hunt desti- 
nation. Dial th -digit number using the dial 
Binary Numbers: 
X = LED on 
All LEDs off = no data 
6A) Return to Step 2 in order to continue with 
this program 
. . or . . . 
6B) Go to Step 2 in another program table 
. . . or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
NO TE. 
For multiple station programming, refer to Paragraph 02.10. 
-82-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 57 
PROGRAM 7XX 
STATION OUTGOING CALL RESTRICTION 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
.- 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial ilaon the dial pad (XX = the number of SPKR LED flashes continuously. 
the station(s) to be programmed). CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. If the LED is already on, depressing its associated 
0 LED ON = Restricted outgoing calls. 
key will turn it off and vice versa. LEDs may be 
0 Each CO key/LED represents itself-that turned off and on until the desired pattern is set. 
is, if LED 01 is on, then the station being 
programmed (XX) is restricted from outgo- 
ing calls on COl, etc. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. I 
6A) Return to Step 2 in order to continue with 
this program 
or . . 
6B) Go to Step 2 in’another program table 
. . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
For multiple station programming, refer to Paragraph 02.10. 
-83-  
						

							~ ..__.U . . . . m ..,.I” . ..-“LY”IsLsJ 
SECTION 500-036-300 
JANUARY 1988 
TABLE 58 
PROGRAM 81XX - 89XX 
CO RINGING ASSIGNMENTS (DAY/DAY2/NIGHT) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station--l 3/l 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial Bu pg on the dial pad (Y = 1 - 9”; XX = SPKR LED flashes continuously. 
the number of station(s) to be programmed). CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. If the LED is already on, depressing its associated 
l LED ON = Ringing assigned. 
l Each CO key/LED represents itself-that key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
is, if LED 01 is on, then the station being 
programmed (XX) is allowed access to 
COl, etc. 
5) Depress the m key to place new data in All station 131’17 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
or . . 
6B) Go to Step 2 in’another program table 
. . or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
*I = DAY-immediate 
2 = DAY-12-seconds delay 
3 = DAY-24-seconds delay 4 = DAY 2-immediate 7 = NIGHT-immediate 
5 = DAY 2-12-seconds delay 
6 = DAY 2-24-seconds delay 8 = NIGHT-12-seconds delay 
9 = NIGHT--24~seconds delay 
NOTE: 
For multiple station programming, refer to Paragraph 02.10. 
-84-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 59 
PROGRAM 9#XX 
DOOR PHONE ASSIGNMENTS 
SET LED on. 
‘1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station’i3/17. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial alIaon the dial pad (XX = the number SPKR LED flashes continuously. 
of the station(s) to be programmed). CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. If the LED is already on, depressing its associated 
l LED ON = Access allowed. key will turn it off and vice versa. LEDs may be 
o Each CO key/LED represents itself-that turned off and on until the desired pattern is set. 
is, if LED 01 is on, then the station being 
programmed (XX) is allowed access to 
COl, etc. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
or . . 
6B) Go to Step 2 in’another program table 
. or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
For multiple station programming, refer to Paragraph 02.10. 
-85  
						

							_ _.--m., ..w..-...w- . ..-----..-” 
SECTION 500-036-300 
JANUARY 1988 
TABLE 60 
PROGRAM *X# 
FLEXIBLE ACCESS CODE NUMBERING 
1) Lock in the SET switch on the HKSU. 
Binary Numbers: 
X = LED on 
All LEDs off = no data 
6B) Transfer data into working memory per Par- 
agraph 02.06. 
-86-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
_ JANUARY 1988 
TABLE 61 
PROGRAM *XX 
FLEXIBLE INTERCOM NUMBERING 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial ~~~on the dial pad (XX= the system in- 
SPKR LED and LED 10 flash continuously. 
tercom number). 
4) Refer to the System Record Sheet. 
Enter the 4-digit Toll Restriction Override As each digit is entered, the entry is verified by 
LEDs as shown below. 
Codes via the dial pad. 
10 1 Flash Steady I 
Binary Numbers: 1 1 2 1 3 1 7 
03 
X = LED on 
LEDs off = no data 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memorv. New data is stored, previous data is erased. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
-87-