Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

							PHUliRAMMlNG PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 42 
PROGRAM 1 #XY 
LEAST COST ROUTING AREA CODE TABLE 
(LCD TELEPHONE REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station ?7. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial flpfl1 (Allow), DpaB (Delete) or pgaa SPKR LED flashes continuously. 
(Display) as required. (X = Route Table 1 - 8.) LCD: (displays dialed number) 
1 # X 2 LCD: DATA = 
4) Press 4 key. 1 # X 3 LCD: DATA = 
1 # X 4 LCD: (displays all allowed codes) 
5) Enter first area code in range sequence LCD: (displays code entered) 
(start). 
6) Depress i key.* LCD: (shifts left to provide space for next code) 
7) Enter final area code in range sequence LCD: (displays code entered) 
(stop).” 
8) Depress a key. Number temporarily stored. 
9) Return to Step 5 to enter additional area 
codes. 
10) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
11A) Return to Step 2 in order to continue with 
this program 
or. . . 
11 B) Go to Step 2’in’another program table 
. . or . . . 
11 C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 6 and 7 if only one area code in sequence is being entered. 
-68-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 43 
PROGRAM 1 #X8Y 
LEAST COST ROUTE DEFINITION 
(LCD EKT REQUIRED-STRATA Vie only) 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 17. 
3) Dial BlIag on the dial pad. X = Route Table 
1 - 8: Y = Route Definition 1 - 4. 
4) Refer to the System Record Sheet. 
Using the dial pad, enter the Route Definition 
number and Modified Digits Table number. 
5) Depress the irr;m key to place new data in 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED on. 
Station 17 LED 19 on. 
System is in program mode. - 
Normal functions halt on station; 7. 
LCD: PROGRAM MODE 
SPKR LED steady on. 
LCD: PROGRAM NO.?. 
SPKR LED flashes continuously. 
LCD: DATA = 
LEDs 00, 01,02 & 03 show data in binary format. 
LEDs 10 & 11 indicate which digits are being dis- 
played. 
All station 17 LEDs (except 19) go off. 
SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-69-  
						

							IVWUHAMMINti tWJlitUlJH~~ 
SECTION 500-036-300 
JANUARY 1988 
TABLE 44 
PROGRAM l#X50 - 53 
START TIME A SCHEDULE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 147. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial flIEfIa - 11 on the dial pad. X = Route SPKR LED flashes continuously. 
Table 1 - 8. LCD: (displays dialed number) 
4) Refer to the System Record Sheet. LCD: (displays code entered) 
Enter the required data for 50- 53 via the dial 
pad. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
or. . . 
6B) Go to Step 2 in’another program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-7o-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 45 
PROGRAM l#X60 - 63 
START TIME B SCHEDULE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial ~I~~~ - uaon the dial pad. X = Route SPKR LED flashes continuously. 
Table 1 - 8. LCD: (displays dialed number) 
4) Refer to the System Record Sheet. LCD: (displays code entered) 
Enter the required data for 60- 63 via the dial 
pad. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
6B) Go to Step 2 in’anzther program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-71-  
						

							rnuunnMMllYLl rnubeuunm 
SECTION 500-036-300 
JANUARY 1988 
TABLE 46 
PROGRAM l#X70 - 73 
START TIME C SCHEDULE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 17. 
3) Dial p~~~~ - al on the dial pad. X = Route 
Table 1 - 8. 
4) Refer to the System Record Sheet. 
Enter the required data for 70- 73 via the dial 
pad. 
5) Depress the cnr;l key to place new data in 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in’anzther program table 
. . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station W. 
LCD: PROGRAM MODE 
SPKR LED steady on. 
LCD: PROGRAM NO.? 
SPKR LED flashes continuouslv. 
LCD: (displays dialed number) ’ 
LCD: (displays code entered) 
All station 17 LEDs (except 19) go off. 
SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-72-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 47 
PROGRAM 1#9XY 
MODIFIED DIGITS TABLE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
Station 17 LED 19 on. 
1) Lock in the SET switch on the HKSU. System is in program mode. .*- 
I Normal functions halt on station 17. 
1 LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial ~l~~~on the dial pad. X = Modified Dig- SPKR LED flashes continuously. 
its Table 1 - 6, Y = (0) delete, (1) add. LCD. (displays dialed number) 
Various LEDs indicate present data. 
4) Refer to the System Record Sheet. 1 LCD: (displays digits entered) 
Using the dial pad: 
A) Delete Table: Enter the quantity of digits to KEY/LED 
PAUSE 
be deleted from the dialed number. 08 16 
B) AddTable: Entertherequiredmodifieddig- 
its to be added to the dialed number. To in- 07 14 
sert pauses (see table for duration in sec- 06 12 * 
onds) while adding digits, press the 05 10 ’ 
appropriate key when pause is required. 04 8 
NOTE: 
Digits may be added or deleted in the same 
Modified Digits Table. 
‘=I 03 6 
02 4 
I 01 I 2 
i 
I 
5) Depress the [5nr;l key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
’ SA) Return to Step 2 in order to continue with 
this program 
SB) Go to Step 2 in’anyther program table 
. . or . . 
~ 6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
. .  . 
-73-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 48 
PROGRAM 2#XY 
LEAST COST ROUTING AREA/OFFICE CODE EXCEPTION TABLE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
.- 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial ~~~~ I on the dial pad. X = Area/Office SPKR LED & LED 10 flash continuously. 
Code Table 1 - 8. 
4) Refer to System Record Sheet. 
Enter Route Table number (1 - 8). 
5) Depress the m key. LCD: (displays table number) 
6) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
7) Dial g/JIa on the dial pad. X = Area/Office LCD: (displays dialed number) then . . . 
Code Table 1 - 8. DATA = 
8) Enter Area Code via the dial pad. LCD: (displays area code entered) 
9) Depress the m key. 
10) Depress the m key. SPKR LED steady on. 
LCD: PROGRAM NO.? 
11) Dial glaa (Add), IIIEi (Delete), or BIIa (Dis- SPKR LED flashes continuously. 
play). X = Area/Office Code Table 1 - 8. LCD: (displays dialed number) 
2 # X 2 LCD: DATA = 
12) Depress a key. 2 # X 3 LCD: DATA = 
2 # X 4 LCD: (displays all currently programmed 
office codes) 
13) Enter first Area Code in range sequence LCD: (displays code entered) 
(start). 
14) Depress 1 key.” LCD: (shifts left to provide space for next code) 
15) Enter final Area Code in range sequence LCD: (displays code entered) 
(stop).” 
16) Depress /J key. 
17) Return to Step 10 to enter additional Area 
Codes. 
18) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
19A) Go to step 2 in another program table 
. . . or . , 
196) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 14 and 15 if only one area code in sequence is being entered.  
						

							TABLE 49 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
PROGRAM 3XX 
STATION CO LINE ACCESS 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. .+ 
Normal functions halt on station 13/j 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial BflBon the dial pad (XX = the number of 
SPKR LED flashes continuously. 
the station(s) to be programmed). The CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. 
0 LED ON = Access allowed. If the LED is already on, depressing its associated 
l Each CO key/LED represents itself-that key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
is, if LED 01 is on, then the station being 
programmed (XX) is allowed access to 
CO1 , etc. 
5) Depress the rX;;m key to place new data in 
Ail station 13/l 7 LEDs (except 19) gp off. _ 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
6B) Go to Step 2 in’an:ther program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
For multiple station programming, refer to Paragraph 02.10. 
-75-  
						

							rnuunAMMlNlI rnubcuunta 
SECTION 500-036-300 
JANUARY 1988 
TABLE 50 
PROGRAM 3#XX 
HOXB, HMDB and HIOB ENABLE 
1) Lock in the SET switch on the HKSU. 
Using the appropriate keys, turn their asso- 
ciated LEDs on or off, as required. The de- If the LED is already on, depressing the associated 
key will turn it off and vice versa. LEDs may be 
66) Go to Step 2 in’in$h& program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. 
NOTE: 
For multiple station programming, refer to Paragraph 02.10. 
-76-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 51 
PROGRAM 4XX 
STATION TYPE ASSIGNMENT 
(This program must be completed before Program 4#XX.) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/17. 
2) Depress the m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial PPaon the dial pad (XX = the number of SPKR LED flashes continuously. 
the station(s) to be programmed). The CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. If the LED is already on, depressing its associated 
key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program < 
66) Go to Step 2 in’&$her program table 
. . . or . . . 
6C) Transfer 
data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE: 
For multiple station programming, refer to Paragraph 02.10. 
f KEY/LED I 
FEATURE 
1 
-77-