Toshiba Strata E Electronic Key Telephone System Installation And Maintenance Manual

							FWJliKAMMlNti PHUL;tUUHtS 
SECTION 500-036-300 
JANUARY 1988 
TABLE 12 
PROGRAM 05 
AUTOMATIC RECALL FROM HOLD TIMING 
(This program is used only if LEDs 10, 11 and 12 are ALL off in Program 5#XX.) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13717. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial la on the dial pad. SPKR LED flashes continuously. 
One LED indicates present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the various keys, turn an associated be on. 
LED on or off, as required. The detailed mean- Only one LED is permitted to be on, depressing an- 
ing of each key/LED is shown below. other key will turn that LED on and turn off the pre- 
MOTE: vious LED. 
If any key/LED is not shown, it is not used 
KEY/LED 
LED ON 
07 
160 seconds 
06 
128 seconds 
05 
96 seconds 
04 64 seconds 
___ 
03 
48 seconds 
02 
32 seconds 
01 16 seconds 
-z- 
No Recall 
5) Depress the L3;rr;l key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . 
68) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
-38-  
						

							TABLE 13 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
_ JANUARY 1988 
PROGRAM 0#5 
CAMP-ON TIMEOUT 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial 1 flu on the dial pad. SPKR LED flashes continuously. 
One LED indicates present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the various keys, turn an associated be on. 
LED on or off, as required. The detailed mean- 
ing of each key/LED is shown below. Only one LED is permitted to be on; depressing 
another key will turn that LED on and turn off the 
NOTE: previous LED. 
If any key/LED is not shown, it is not used.. Tech l&o lrw. Cdl [S+Q) ci??+ e@= 
KEY/LED 
LED ON . 
03 
64 seconds 
02 
48 seconds 
01 
32 seconds 
00 
16 seconds 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer data into working memory per Pa- 
ragraph 02.06. 
SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
-39-  
						

							, ImvumI~IvIIIII~~~ r mbruunc4 
SECTION 500-036-300 
JANUARY 1988 
TABLE 14 
-_ 
PROGRAM 06 
AUTOMATIC RELEASE ON HOLD ENABLE 
, . 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. 
3) Dial 88 on the dial pad. Normal functions halt on statiorYl3/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
Using the various keys, turn their associated 
LEDs on or off, as required. Each CO key/LED 
represents itself-that is, if LED 01 is on, CO1 
will have AROH during normal operation. If 
t;,‘,” 01 is off, AROH will not function on that An X on the record sheet means the LED should 
be on (AROH enabled). 
If the LED is already on, depressing the associated 
key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
5) Depress the m;n;l key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memorv. 
6A) Go to Step 2 in another program table 
. . . or . . 
66) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTES. 
1. This program is used to release Trunk-to-Trunk connections if enabled with 
Programs 02 and 
0#6. 
2. 
If Automatic Release from Hold is available, the CO will automatically drop the lines when the 
outside party hangs up. However, if Automatic Release from Hold is not available, the person who 
set up the trunk-to-trunk connection must occasionally monitor the call and disconnect the CO 
lines when the two parties hang up. 
-4o-  
						

							TABLE 15 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
_ JANUARY 1988 
PROGRAM 0#6 
TRUNK-to-TRUNK CONNECTION ENABLE 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the w key on station 13/l 7. 
3) Dial 111 on the dial pad. Station 13/17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the various keys, turn their associated 
be on. 
LEDs on or off, as required. Each CO key/LED 
represents itself-that is, if LED 01 is on, CO1 If the LED is already on, &pressing the associated 
will be allowed trunk-to-trunk connection, if key will turn it off and vice versa. LEDs may be 
LED 01 is off, trunk-to-trunk connection will turned off and on until the desired pattern is set. 
not be allowed on that line, etc. 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. _ 
memory. 
6A) Go to Step 2 in another program table 
or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
-41-  
						

							rnuunbwlrviIIu4.a rfwawtsts 
SECTION 500-036-300 
JANUARY 1988 
TABLE 16 
PROGRAM 07 
AUTOMATIC RELEASE ON HOLD TIMING 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. 
3) Dial ii on the dial pad. Normal functions halt on station ‘B/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. Each CO 
key/LED represents itself-that is, if LED 01 If the LED is already on, depressing the associated 
is on, CO1 wili have X6 (crossbar) timing for key will turn it off and vice versa. LEDs may be 
AROH. If LED 01 is off, CO1 will have ESS turned off and on until the desired pattern is set. 
(electronic) timing, etc. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. or . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE: 
This program affects only those CO lines enabled via 
Program 06 [AROH should be enabled for 
Trunk- to- Trunk connections}. 
-42-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
TABLE 17 
PROGRAM 0#7 
AUTOMATIC RELEASE ON HOLD TIMING 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/17. 
3) Dial 81a on the dial pad. Station 13/l 7 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 13/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. Each CO If the LED is already on, depressing the associated 
key/LED represents itself-that is, if LED 01 key will turn it off and vice versa. LEDs may be 
is on, CO1 is bridged with the lA2 system. If 
turned off and on until the desired pattern is set. 
LED 01 is off, CO1 is not bridged, etc. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table < 
. . . or . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
-43-  
						

							PlWWlAMMING PRCJGEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 18 
PROGRAM 08 
CO LINE CALL PICKUP SELECTION 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. 
3) Dial 41 on the dial pad. Normal functions halt on station*‘? 3/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- 
be on. 
ciated LEDs on or off, as required. Each CO 
key/LED represents itself-that is, if LED 01 If the LED is already on, depressing the associated 
is on, CO1 will belong to CPU #2. If LED 01 key will turn it off and vice versa. LEDs may be 
is off, CO1 will belong to CPU #l. turned off and on until the desired pattern is set. 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE: 
This program will have no meaning unless Call Pickup was selected in 
Program 03. 
-44-  
						

							TABLE 19 PROGRAMMING PROCEDURES 
SECTION 500-036-300 s 
- JANUARY 1988 
PROGRAM 0#8 
NIGHT RINGING OVER EXTERNAL PAGE 
(STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 17. 
3) Dial BflB on the dial pad. Station 17 LED 19 on. 
System is in program mode. .*- 
Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. Each CO If the LED is already on, depressing the associated 
key/LED represents itself-that is, if LED 01 key will turn it off and vice versa. LEDs may be 
is on, when the system is in night operation, turned off and on until the desired pattern is set. 
incoming calls over that CO line will ring over 
the external page; if LED 01 is off, incoming 
calls over that CO line will not ring in night 
operation, etc. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
Use this program only if LED 02 is on in 
Program 02. 
-45-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 20 
PROGRAM 09 
SINGLE CO LINE (DIAL 9) GROUP SELECTION 
I . 
1 SET LED on. .* 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. Normal functions halt on station 13/l? 
SPKR LED steady on. 
3) Dial 31 on the dial pad. 
4) Refer to the System Record Sheet. 
Using the appropriate keys, turn their asso- 
ciated LEDs on or off, as required. Each CO 
key/LED represents itself-that is, if LED 01 
is on, CO1 will be included in the “Dial 9” 
arouo. 
5) Depress the m key to place new data in 
memorv. SPKR LED flashes continuously. 
CO LEDs indicate present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the associated 
key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
All station 13/l 7 LEDs (except 19) go off. 
6A) Go to Step 2 in another program table 
. . or 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE: 
Use this program only if LED 15 is off in Program 01. 
-46-  
						

							TABLE 21 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
- JANUARY 1988 
PROGRAM 09X 
CO LINE GROUPS (DIAL 91 - 98) ASSIGNMENTS 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 8‘ 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial mua on the dial pad. (X = 1 - 8 depending SPKR LED flashes continuously. 
upon the group being defined.) Dial aug for CO LEDs indicate present data. 
“Dial 91” group; 114 for “Dial 92” group, etc. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. Each CO If the LED is already on, depressing the associated 
key/LED represents itself-that is, if LED 01 key will turn it off and vice versa. LEDs may be 
is on, CO1 will be included in the “Dial 9X” turned off and on until the desired pattern is set. 
group. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. i 
6A) Return to Step 2 in order to continue with 
this program 
or . . 
6B) Go to Step 2 in’another program table 
. . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
Use this program only if LED 
15 is on in Program 01. 
-47-