Panasonic Software DP-2310/3010/3510/3520/4510/4520/6010/6020 Document Management System And Printer Operating Instructions

							Configuring the Printer Driver Settings
71
Windows 2000/XP (Administrator)
Printer Section
Device Options Tab (For DP-3510/3520/4510/4520/6010/6020)
1.Finisher
Select the type of the finisher if one is installed.
2.Punch Unit
Select Installed if the Punch Unit is installed.
3.Large Capacity Paper Tray (LCT)
Select Installed if the Large Capacity Paper Tray is installed.
4.HDD
Select Installed if the HDD Unit is installed.
5.Halftone Setup
 button
Select the halftoning method to be used (halftones specific to the printer).
Select it according to the details of the data and your preference.
Halftone Setup...
Continued on the next page... 
						

							Configuring the Printer Driver Settings
72
Windows 2000/XP (Administrator)
•Halftone Pattern
Select the pixel size to be used for halftones.
The greater the value, the coarser the image would become. However, a larger value is suited for
printing large areas.
The Enhanced pattern allows printing at a higher resolution using the same number of pixels. However,
the pattern might generate unnatural lines, patterns, moire effects, and so on depending on the image to
be printed.
•Device Gamma
Adjust the gamma of print images (color intensities).
•Pixel Diameter
Adjust the darkness of the print image. Move the slider to specify the pixel size. You can choose
between specifying the real size in inches or specifying it as a percentage relative to the printer
resolution.
•Luminance (CIE Y)
Adjust the luminosity of the print image.
6. button (DP-3520/4520/6020 only)
When your machine is connected onto the network (TCP/IP), click this button to set the Options
Configuration automatically.
7.Number of Paper Trays
Select the number of available paper trays if optional Paper Feed Module(s) are installed.
8.  button (DP-3520/4520/6020, For USA only)
Edit the URL address that will be displayed when clicking the   button of the
Paper Tab (see page 75).
NOTE1Device Options  Tab specifies device-specific settings and settings of optional devices.•URL Title
Enter an applicable URL title.
•URL
Enter the URL address to be associated to the
  button of the Paper Tab.
•Contact
Enter applicable contact information
(i.e.: The email address of the contact person)
Auto Configuration
Edit URL...
Support Contacts (W)...
Support Contacts (W)... 
						

							Configuring the Printer Driver Settings
73
Printer Section
Changes the printer settings. Display the printer settings dialog box by performing the steps below.
NOTE1. In Windows 2000/XP, setting the properties depends on the logon accounts. This section
describes properties to be specified by a user, upon executing a print operation in an
application. See Configuring the Printer Driver Settings (Administrator) for details on
administrator (system manager) properties. (See page 62)
Windows 2000/XP (User)
1
Select Print in the File menu of the application.
2
Select the printer model in the name list box.
3Click the   button in the Print dialog box. 
4
The printer properties dialog box appears. Click the
desired tabs of the dialog box and specify the properties.
(See Note 1)
(See pages 74 - 81)
Properties... 
						

							Configuring the Printer Driver Settings
74
Paper Tab
1.Paper Size
Select a document size.
2.Copies (DP-2310/3010/3520/4520/6020: 1-999, DP-3510/4510/6010: 1-250)
Specify the number of copies to be printed.  If the number of copies to be printed can be specified within
the application, indicate one copy here and specify the number of copies in the Print dialog box of the
application.
3.Orientation
Specifies how the document is positioned on the page. Portrait orients the print vertically. Landscape
orients the print horizontally. If available, Rotated Landscape rotates the paper 90 degrees
counterclockwise.
4.Output Size
Specifies the paper size to use. The various paper sizes listed match those supported by your printer. 
5.Zoom (50-200)
Specify an enlargement or reduction percentage when printing documents.  If enlargement/reduction can
be set within the application, indicate 100% here and specify the enlargement/reduction percentage in
the Print dialog box of the application.
6.Paper Source
Specify where the paper you want to use is located in the device.  If you choose Auto Tray Selection,
the printer driver will automatically select an appropriate tray according to the Paper Size selected.
7.Print Properties Status Icons
Show the print status for the following properties.
• Paper Style (Output Tab)
• N in 1 (Output Tab)
• Sort (Output Tab)
8.Status Monitor
Recalls Network Status Monitor. (See page 170)
All Windows Common Settings
Continued on the next page... 
						

							Configuring the Printer Driver Settings
75
All Windows Common Settings
Printer Section
9.  button (DP-3520/4520/6020, For USA only)
Open the Support window. The URL address(es) will be displayed if they were entered in the Device
Options Tab. Click the   button to open the Web page.Support Contacts (W)...
Go to Web 
						

							Configuring the Printer Driver Settings
76
All Windows Common Settings
 Output Tab
1.Paper Style
Select duplex printing for printing on both sides of the paper.
You can select the printing style among 1-Side/2-Sided (Long Edge) /2-Sided (Long Edge Margin) /2-
Sided (Short Edge) /2-Sided (Short Edge Margin).
•Binding Direction
Select the binding side (Long Edge/Short Edge) for duplex printing.
•Binding Margin
Select the binding margin upon duplex printing. The width of the binding margin is specified on the
device.
2.N in 1
Specify the layout pattern for printing multiple documents on a single sheet of paper. 
  
						

							Configuring the Printer Driver Settings
77
All Windows Common Settings
Printer Section
3.Sort
Select whether to Stack or Sort when printing multiple copies.
Note:Sort settings made on the printer driver screen have priority.
It is not  recommended to make them on the application screen. 
4.Staple
Select the staple position. Available if the optional Finisher (DA-FS300, FS330, FS355, FS600 or FS605) 
is installed. Available for up to 30 sheets (Letter/A4).
Portrait (Left 1/Left 2/Right 1/Right 2 Position)
Landscape (Left 1/Right 1/Top Position)
For DA-FS330, 355, 600 or 605
Portrait (Left 1/Right 1 Position)
Landscape (Left 1/Right 1 Position)
For DA-FS300
Continued on the next page... 
						

							Configuring the Printer Driver Settings
78
All Windows Common Settings
5.Punch (For DP-3510/3520/4510/4520/6010/6020 only)
Select the punch position. Available if the optional Punch Unit (DA-SP31) is installed.
You can choose Left/Right/Top regardless of paper orientation.
6.Finisher Bin/Output Tray
You can select the type of the output bin or tray.
Possible when the optional finisher is installed.
Note: 
Before selecting the Inner Upper Exit Tray, please ensure that the Exit Tray (Inner) (DA-XN200) is
installed.
Portrait (Left/Right Position) (Top Position)
Landscape (Left/Right Position) (Top Position) 
						

							Configuring the Printer Driver Settings
79
All Windows Common Settings
Printer Section
7. Button
•Print All Text as Black (Windows 98/Me only).
All colored text is printed as solid black
•Print Blank Pages
Select whether the blank pages are printed.
•Duplex Notice (For DP-2310/3010 only)
Check whether 2-Sided Print is printed on the footer of 1st page when printing with 2-Sided Page
Style.
•Copies
When printing a large amount of data with sort mode, the machine might not be able to print
due to lack of memory capacity.
In this case, select Print Controlled, as sorting is processed by the printer driver. However, this mode
may take more time to print.Advanced... 
						

							Configuring the Printer Driver Settings
80
All Windows Common Settings
Quality Tab
1.Halftone (For Windows 98/Me only)
Select either None or Dither.
2.Resolution
Select the print resolution (300 dpi / 600 dpi). (See Note1) 
3.Contrast
Adjust the contrast of print images. (Note: Only if Halftone is set to None.)
4.  button (For Windows NT/2000/XP only)
•Contrast
Adjust the contrast of print images.
•Brightness
Adjust the brightness of print images.
•Dark Picture
Select this option in order to print dark images brighter.
•Negative
Select this option in order to print images with black and white reversed.
•Input RGB Gamma
Adjust the gamma of print images (color intensities). Red, Green and Blue can also be adjusted
individually.
•Black Ref/White Ref
Adjust the difference between the darkest and lightest colors of an image. Increasing the Black Ref
value or decreasing the White Ref value will intensify the contrast of the image but reduces the range of
colors in between.
•Picture
Select a test pattern type.
Selecting the View check box will display halftone adjustment results in the test pattern.
NOTE1. dpi (dots per inch) represents the number of dots contained in one inch.  The larger the value,
the higher the resolution would be.
 

Halftone Color Adjustment...