Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

							4.2 System Programming
Extension Name Setting
604
System Programming  4-103
DescriptionAssigns names to the extensions.
Selection• Jack number: 01 – 24
• Name: 10 characters (max.)
DefaultAll jacks – Not stored
Programming1.Enter 604.
Display: Extension Name
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display: #01:
4.Enter a name.
For entering characters, see Section 4.1.3 “Entering Characters”.
To delete the current entry, press CLEAR.
To change the current entry, press CLEARand enter the new name.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Conditions• There is a maximum of 24 names. Each name has a maximum of
10 characters.
• Program [009] “Extension Number Assignment” is used to assign the
extension numbers.
Feature ReferencesSection 3, Features
Display, Call Information
Display, in Idle
Intercom Calling 
						

							4-104 System Programming
4.2 System Programming
Account Code Entry Mode
605
DescriptionSelects the account code input mode for each extension jack. There
are four account code modes: Option, Forced, Verify-All and
Verify-Toll.
Option mode:The user can enter any account code, if
needed.
Forced mode:The user must always enter an account code.
The code can be any number.
Verify – All mode:The user must always enter a pre-assigned
account code to make an outside call.
Verify – Toll mode:The user can enter an assigned account code
to override toll restriction. The toll restriction
COS numbers 3 through 5 will be changed
temporarily to the COS number 2. (The COS
numbers 1 and 2 will not be changed.)
Selection• Jack number: 01 – 24, ( = all jacks)
• Option / Forced / Verify – All / Verify – Toll
DefaultAll jacks – Option
Programming1.Enter 605.
Display: Call Accounting
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display: #01:Option
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END. 
						

							4.2 System Programming
Account Code Entry Mode(contd.)
605
System Programming  4-105
Conditions• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
• Program [310] “Account Codes” is used to define the Account Codes for
the Verify modes.
• Programs [601]–[603] “TRS – Class of Service (COS) Assignment —
Day/Night/Lunch” is used to assign a Class of Service to each extension.
Feature ReferencesSection 3, Features
Account Code Entry
Toll Restriction Override by Account Codes 
						

							4-106 System Programming
4.2 System Programming
Call Transfer to an Outside (CO) Line
606
DescriptionEnables or disables performing the Call Transfer to an Outside
(CO) Line feature.
Selection• Jack number: 01 – 24, ( = all jacks)
• Enable / Disable
DefaultDisable
Programming1.Enter 606.
Display: Transfer to CO
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
Feature ReferenceSection 3, Features
Call Transfer, Screened – to an Outside (CO) Line  
						

							4.2 System Programming
Call Forwarding to an Outside (CO) Line
607
System Programming  4-107
DescriptionEnables or disables performing the Call Forwarding to an Outside
(CO) Line feature.
Selection• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll jacks – Disable 
Programming1.Enter 607.
Display: CO Forward
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
Feature ReferenceSection 3, Features
Call Forwarding – to an Outside (CO) Line 
						

							4-108 System Programming
4.2 System Programming
Executive Busy Override
608
DescriptionEnables or disables performing Executive Busy Override –
Extension/Outside (CO) Line. Executive Busy Override allows a
user to interrupt an established call.
Selection• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll jacks – Disable
Programming1.Enter 608.
Display: Busy Override
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
Feature ReferencesSection 3, Features
Executive Busy Override – Extension
Executive Busy Override – Outside (CO) Line 
						

							4.2 System Programming
Do Not Disturb Override
609
System Programming  4-109
DescriptionEnables or disables performing the Do Not Disturb (DND)
Override feature.
Selection• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll jacks – Disable
Programming1.Enter 609.
Display: DND Override
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
Feature ReferenceSection 3, Features
Do Not Disturb (DND) Override 
						

							4-110 System Programming
4.2 System Programming
Paralleled Telephone Connection
610
DescriptionA Paralleled Telephone Connection allows a single line telephone
to be connected to the same jack as a proprietary telephone. This
program assigns which jacks can perform the paralleled telephone
connection feature.
Selection• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll jacks – Disable
Programming1.Enter 610.
Display: Parallel Connect
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
Feature ReferenceSection 3, Features
Paralleled Telephone 
						

							4.2 System Programming
TAM (Telephone Answering Machine) Extension
611
System Programming  4-111
DescriptionAssigns the jacks that can accept a TAM connection. When a jack
is TAM-enabled, the “Call Retrieving from a TAM” feature
becomes available.
Selection• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll jacks – Disable
Programming1.Enter 611.
Display: TAM Extension
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
Feature ReferenceSection 3, Features
Call Retrieving from a TAM (Telephone Answering Machine) 
						

							4-112 System Programming
4.2 System Programming
Room Monitor Assignment
612
DescriptionAssigns which extensions can be monitored by another telephone.
Selection• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll jacks – Disable
Programming1.Enter 612.
Display: Room Monitor
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Disable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another jack, press NEXTor PREV, or
SELECTand enter the desired jack number.
7.Repeat steps 4 through 6.
8.Press END.
Conditions• To assign all jacks to the same selection, press the  key in step 3. In
this case, the display will show:# :Mixed.
• The jacks which are assigned to “DISABLE” cannot accept feature
number “7351#” for the room monitor feature.
Feature ReferenceSection 3, Features
Room Monitor