Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

							4.2 System Programming
DISA Built-in Auto Attendant
501
System Programming  4-83
DescriptionAssigns the DISA built-in auto attendant number. The extension
number can be assigned as a one digit number and used as a DISA
built-in auto attendant number.
Selection• DISA built-in auto attendant (AA) number: 0 – 9
• Jack number: 01 – 24 / Ring Group number: 1 – 8
DefaultAll numbers — Not stored
Programming1.Enter 501.
Display: DISA Built-In
2.Press NEXT.
Display example: AA NO? ®
3.Enter a DISA built-in auto attendant number.
Pressing NEXTalso can enter DISA AA number 0.
Display example: 0: Not Stored
4.Press SELECTuntil the desired selection is displayed and
enter an extension or ring group number.
To change the current entry, press CLEARand enter the new
number.
Display example: 0: Jack-01
5.Press STORE.
6.To program another DISA AA number, press NEXTor
PREV, or SELECTand enter the desired DISA AA
number.
7.Repeat steps 4 through 6.
8.Press END.
Conditions• To enable this feature, the user must select “With AA” in program
[500] “DISA Incoming Dialing Mode Selection”.
• This system can store up to ten programmable DISA built-in auto
attendant numbers.
• If the user would like to use a line access number “9” and/or operator
number “0” in the “With AA” mode, do not assign auto attendant
number(s) which correspond to the line access number and/or operator
number (0 and/or 9).
Feature ReferenceSection 3, Features
Direct Inward System Access (DISA) 
						

							4-84 System Programming
4.2 System Programming
OGM Mode Selection
502
DescriptionSelects how the two outgoing messages (OGM) are used. There are
two modes as follows.
MODE 1: both OGM1 and OGM2 are used for DISA1 so that the
system can receive two incoming calls via DISA at the
same time.
MODE 2: OGM1 is used for DISA1 and OGM2 is used for
DISA2.
SelectionMODE 1 / MODE 2
DefaultMODE 1
Programming1.Enter 502.
Display: OGM Selection
2.Press NEXT.
Display example: MODE 1
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Conditions• Program [414]–[416] “Outside (CO) Line Mode — Day/Night/Lunch”
are used to assign DISA1 or DISA2 to each outside (CO) line according
to this assignment.
• If an optional OGM/FAX Detection card is not installed, this assignment
should be “MODE 1”.
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Data Line Security
Outgoing Message (OGM) 
						

							4.2 System Programming
FAX Connection
503
System Programming  4-85
DescriptionAssigns which jack can receive facsimile data when the system
receives a facsimile transmission signal via the Direct Inward
System Access (DISA) feature.
SelectionJack number: 01 – 24 / Disable(Facsimile data cannot be received.)
DefaultDisable
Programming1.Enter 503.
Display: Fax Connection
2.Press NEXT.
Display example: FAX :Disable
3.Enter a jack number.
To assign no FAX jack, press CLEAR.
To delete the jack number, press CLEAR.
To change the current entry, press CLEARand enter the new
number.
4.Press STORE.
5.Press END.
Conditions• The extension assigned as the fax extension will automatically have the
Data Line Security feature set.
• An optional OGM/FAX Detection card is necessary.
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Data Line Security
Facsimile Detection 
						

							4-86 System Programming
4.2 System Programming
DISA Delayed Answer Time
504
DescriptionAssigns the time from a call being received and answered using the
DISA feature.
Selection0 sec / 3 sec / 6 sec / 12 sec(seconds)
Default3 sec
Programming1.Enter 504.
Display: Ans Delay Time
2.Press NEXT.
Display example: Time: 3sec
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• The outside (CO) lines which are assigned as “Enable” in program [900]
“Caller ID Assignment” are always set to 6 seconds even if “0 sec” or
“3 sec” is selected in this program.
Feature ReferencesSection 3, Features
Caller ID
Direct Inward System Access (DISA) 
						

							4.2 System Programming
DISA Waiting Time after OGM
505
System Programming  4-87
DescriptionSelects the time that the system waits for the DTMF signals or
CNG tone after the outgoing message.
Selection0 sec / 5 sec / 10 sec / 15 sec(seconds)
Default5 sec
Programming1.Enter 505.
Display: DISA Wait Time
2.Press NEXT.
Display example: Time :5sec
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• An optional OGM/FAX Detection card is necessary.
Feature ReferenceSection 3, Features
Direct Inward System Access (DISA) 
						

							4-88 System Programming
4.2 System Programming
DISA Busy Mode
506
DescriptionSelects the mode when destination extension of the call via DISA is
busy. There are three modes as follows.
Call Waiting: a call waiting tone is sent and then the call is held
until the called party responds.
Disconnect: the call is disconnected after the busy tone.
DISA2: OGM2 is sent to the caller and the system waits for
another destination when the first destination is busy.
SelectionCall Waiting / Disconnect / DISA2
DefaultDisconnect
Programming1.Enter 506.
Display: DISA Busy Mode
2.Press NEXT.
Display example: Disconnect
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• In program [502] “OGM Mode Selection”, “MODE2” should be
selected if “DISA2” is selected in this program.
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Outgoing Message (OGM) 
						

							4.2 System Programming
DISA Intercept Mode
507
System Programming  4-89
DescriptionIntercept Routing provides an automatic re-direction of DISA calls
which cannot or have not been answered within the programmed
time. This program is used to select whether the call is
disconnected or re-directed.
Intercept: the call is directed to the extensions assigned in
programs [408]–[410].
Disconnect: the call is disconnected.
SelectionDisconnect / Intercept
DefaultIntercept
Programming1.Enter 507.
Display: DISA IRNA Mode
2.Press NEXT.
Display example: Intercept
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Intercept Routing
Voice Mail Integration for KX-TVS50
Voice Mail Integration for KX-TVS75/KX-TVS100 
						

							4-90 System Programming
4.2 System Programming
DISA Ringing Time before Intercept
508
DescriptionSelects the time for the Intercept Routing — No Answer (IRNA)
feature. If a DISA call is not answered within the programmed
time, the call will be redirected to the programmed extension.
Selection10 sec / 20 sec / 30 sec / 40 sec / 60 sec / 120 sec(seconds)
Default20 sec
Programming1.Enter 508.
Display: DISA Befor IRNA
2.Press NEXT.
Display example: Time: 20sec
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• Programs [408]–[410] “Flexible Ringing Assignment —
Day/Night/Lunch” are used to program the destination of Intercept
Routing in the day, night and lunch modes.
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Intercept Routing 
						

							4.2 System Programming
DISA Ringing Time after Intercept
509
System Programming  4-91
DescriptionSelects the time that the extension will ring for after being
re-directed by the Intercept Routing — No Answer (IRNA) feature.
If a call is not answered within the programmed time, the call will
be disconnected.
Selection10 sec / 20 sec / 30 sec / 40 sec / 60 sec / 120 sec (seconds)
Default20 sec
Programming1.Enter 509.
Display: DISA After IRNA
2.Press NEXT.
Display example: Time: 20sec
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Intercept Routing 
						

							4-92 System Programming
4.2 System Programming
DISA No Dial Mode
510
DescriptionSelects the mode when nothing is dialed after the OGM or a beep
after a programmed length of time for the DISA1 and DISA2
modes. There are two modes as follows.
Intercept: the call is directed to the extensions assigned in
programs [408]–[410] for the time programmed in
[509] “DISA Ringing Time After Intercept”.
Disconnect: the call is disconnected.
Selection• DISA1 / DISA2
• Intercept / Disconnect
DefaultDISA1 and DISA2 — Intercept
Programming1.Enter 510.
Display: No Dial Mode
2.Press NEXT.
Display example: DISA1:Disconnect
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press NEXTor PREVto program the other parameter.
6.Repeat steps 3 through 5.
7.Press END.
ConditionsNone
Feature ReferencesSection 3, Features
Direct Inward System Access (DISA)
Intercept Routing