Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

							4.2 System Programming
Pulse Speed Selection
402
System Programming  4-63
DescriptionAn outside (CO) line set for pulse or call blocking mode in program
[401] “Dial Mode” can have two pulse rates, 10 pps (low) and
20 pps (high). This program sets the pulse speed for each outside
(CO) line which has set the pulse or call blocking mode.
Selection• Outside (CO) line number: 1 – 6,  ( = all outside (CO) lines)
• Low Speed(10 pps)/ High Speed(20 pps)
DefaultAll outside (CO) lines – Low Speed
Programming1.Enter 402.
Display: Pulse Speed
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:Low Speed
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program another outside (CO) line, press NEXTor
PREV, or SELECTand enter the desired outside (CO) line
number.
7.Repeat steps 4 through 6.
8.Press END.
Conditions• To assign all outside (CO) lines to the same selection, press the  key
in step 3. In this case, the display will show:CO :Mixed.
• The required pulse speed is determined by the outside (CO) or Host
PBX line.
Feature ReferenceSection 3, Features
Dial Type Selection 
						

							4-64 System Programming
4.2 System Programming
Host PBX Access Codes
403
DescriptionAssigns Host PBX access codes. If the system is installed behind a
host PBX system, an access code is required to make an outside
call. Up to eight codes can be stored for an outside (CO) line
connected to the host PBX.
Selection• Outside (CO) line number: 1 – 6,  ( = all outside (CO) lines)
• Access code: 1 or 2 digits, eight different entries (max.)
DefaultAll outside (CO) lines – Not stored
Programming1.Enter 403.
Display: Host PBX Access
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:Not Stored
4.Enter an access code.
To delete the current entry, press CLEAR.
To change the current entry, press CLEARand enter the new access
code.
Display example: CO 1:01
5.To enter more access codes for the same outside (CO) line,
press “,” (CONF/SAVE button) and enter the access codes
until all of the required entries are completed.
Display example: CO 1:01,08,10,22
6.Press STORE.
7.To program another outside (CO) line, press NEXTor
PREV, or SELECTand enter the desired outside (CO) line
number.
8.Repeat steps 4 through 7.
9.Press END. 
						

							4.2 System Programming
Host PBX Access Codes (contd.)
403
System Programming  4-65
Conditions• This program is only required if a host PBX is connected to the system.
• There is a maximum of eight access codes per outside (CO) line. Each
code has one or two digits, consisting of 0 – 9.
• When the programmed codes are dialed, Automatic Pause Insertion and
Toll Restriction are applied to all calls. The programmed pause time (in
program [417] “Pause Time”) is automatically inserted after the access
code.
• To assign all outside (CO) lines to the same selection, press the  key
in step 3. In this case, the display will show:CO :Mixed.
Feature ReferencesSection 3, Features
External Feature Access Pause Insertion, Automatic
Host PBX Access 
						

							4-66 System Programming
4.2 System Programming
Outside (CO) Line Group Assignment
404
DescriptionEach outside (CO) line must be assigned to an outside (CO) line
group (trunk group). This program defines the outside (CO) line
group assignment for each outside (CO) line. For example, if there
are multiple telephone service companies available, the outside
(CO) lines can be grouped by company.
Selection• Outside (CO) line number: 1 – 6,  ( = all outside (CO) lines)
• Outside (CO) line group (Trunk) number: 1 – 6
DefaultCO1 — TRK GRP-1; CO5 — TRK GRP-5;
CO2 — TRK GRP-2; CO6 — TRK GRP-6
CO3 — TRK GRP-3;
CO4 — TRK GRP-4;
Programming1.Enter 404.
Display: Trunk Group
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:TRK GRP-1
4.Enter the outside (CO) line group number.
To change the current entry, enter the new outside (CO) line group
number.
5.Press STORE.
6.To program another outside (CO) line, press NEXTor
PREV, or SELECTand enter the desired outside (CO) line
number.
7.Repeat steps 4 through 6.
8.Press END.
Condition• To assign all outside (CO) lines to the same outside (CO) line group,
press the  key in step 3. In this case, the display will show:
CO :Mixed.
Feature ReferenceSection 3, Features
Outside (CO) Line Group 
						

							4.2 System Programming
Flexible Outward Dialing Assignment — Day/Night/Lunch
405–407
System Programming  4-67
DescriptionDetermines which outside (CO) lines can be accessed by an
extension in the day, night and lunch modes. The extension users
can make outgoing outside calls using the assigned outside (CO)
lines.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Jack number: 01 – 24, ( = all jacks)
• Enable / Disable
DefaultAll outside (CO) lines – Enable — Day/Night/Lunch
Programming1.Enter a program address (405 for day, 406 for night or 407
for lunch).
Display example: Day Out CO
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:#01:Enable
4.Enter the desired jack numberafter pressing the #key.
The user can also keep pressing  or  until the desired jack
number is displayed.
5.Keep pressing SELECTuntil the desired selection is
displayed.
6.Press STORE.
7.To program another jack, press  or 
,or #and enter the
desired jack number.
8.Repeat steps 5 through 7.
9.To program another outside (CO) line, press NEXTor
PREV, or SELECTand the desired outside (CO) line
number.
10.Repeat steps 4 through 9.
11.Press END.
Condition• To assign all jacks or outside (CO) lines to the same selection, press the
key in step 3 or 4. In these cases, the display will show:
CO :# :Mixed.
Feature ReferencesSection 3, Features
Outside (CO) Line Connection Assignment – Outgoing
Time (Day/Night/Lunch) Service 
						

							4-68 System Programming
4.2 System Programming
Flexible Ringing Assignment — Day/Night/Lunch
408–410
DescriptionAllows more than one extension to ring in the day, night and lunch
modes. All incoming calls from the programmed outside (CO) lines
are directed to the specified extensions.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Jack number: 01 – 24, ( = all jacks)
• Disable / Enable
DefaultAll outside (CO) lines – all jacks – Enable — Day/Night/Lunch
Programming1.Enter a program address (408 for day, 409 for night or 410
for lunch).
Display example: Day In CO
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:#01:Enable
4.Enter the jack numberafter pressing the #key.
The user can also keep pressing  or  until the desired jack
number is displayed.
5.Keep pressing SELECTuntil the desired selection is
displayed.
6.Press STORE.
7.To program another jack, press  or 
,or #and enter the
desired jack number.
8.Repeat steps 5 through 7.
9.To program another outside (CO) line, press NEXTor
PREV, or SELECTand the desired outside (CO) line
number.
10.Repeat steps 4 through 9.
11.Press END. 
						

							4.2 System Programming
Flexible Ringing Assignment — Day/Night/Lunch (contd.)
408–410
System Programming  4-69
Conditions• An extension can be assigned as the destination for as many outside
(CO) lines required.
• To assign all jacks or all outside (CO) lines to the same selection, press
the  key in step 3 or step 4. In these cases, the display will show:
CO :# :Mixed.
Feature ReferencesSection 3, Features
Ringing, Delayed
Time (Day/Night/Lunch) Service 
						

							4-70 System Programming
4.2 System Programming
Delayed Ringing Assignment — Day/Night/Lunch
411–413
DescriptionAssigns the ringing start time for each jack in the day, night and
lunch modes.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Jack number: 01 – 24, ( = all jacks)
• Immdtly (immediate ringing)/ 5 sec / 10 sec / 15 sec
DefaultAll outside (CO) lines – all jacks – Immdtly — Day/Night/Lunch
Programming1.Enter a program address (411 for day, 412 for night or 413
for lunch).
Display example: Day Delayed CO
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:#01:Immdtly
4.Enter a jack numberafter pressing the #key.
The user can also keep pressing  or  until the desired outside
(CO) line number is displayed.
5.Keep pressing SELECTuntil the desired selection is
displayed.
6.Press STORE.
7.To program another jack, press  or 
,or #and enter the
desired jack number.
8.Repeat steps 5 through 7.
9.To program another outside (CO) line, press NEXTor
PREV, or SELECTand the desired outside (CO) line
number.
10.Repeat steps 4 through 9.
11.Press END. 
						

							4.2 System Programming
Delayed Ringing Assignment — Day/Night/Lunch (contd.)
411–413
System Programming  4-71
Conditions• To assign all jacks or outside (CO) lines to the same selection, press the
key in step 3 or step 4. In these cases, the display will show:
CO :# :Mixed.
• There are four notification methods.
(1) Immediate ringing: rings immediately
(2) 5 second delay
(3) 10 second delay
(4) 15 second delay
Feature ReferencesSection 3, Features
Ringing, Delayed
Time (Day/Night/Lunch) Service 
						

							4-72 System Programming
4.2 System Programming
Outside (CO) Line Mode — Day/Night/Lunch
414–416
DescriptionSelects the mode of an incoming outside call on each outside (CO)
line in the day, night and lunch modes. There are the following four
modes.
Normal: an incoming outside call will be received at the
extension(s) assigned in programs [408]–[410].
DIL: an incoming outside call will be received at the assigned
extension.
DISA1: an incoming outside call will be received at an extension
through the DISA feature. A caller will hear a tone or an
outgoing message.
DISA2: an incoming outside call will be received at an extension
through the DISA feature. A caller might hear OGM 2;
for various configurations please see Cases 2, 3 and 4 in
Section 3, Features “Outgoing Message (OGM)”.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Normal / DIL + extension jack number / DISA1 / DISA2
DefaultNormal
Programming1.Enter a program address (414 for day, 415 for night or 416
for lunch).
Display example: CO Day/Mode
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:Normal
4.Keep pressing SELECTuntil the desired selection is
displayed and if “DIL” is selected, enter the extension jack
number.
5.Press STORE.
6.To program another outside (CO) line, press NEXTor
PREV, or SELECTand enter the desired outside (CO) line
number.
7.Repeat steps 4 through 6.
8.Press END.