Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

							4.2 System Programming
CO Indicator Assignment
109
System Programming  4-33
DescriptionAssigns whether or not an extension user can answer an incoming
outside call when they were was not assigned to receive calls in
programs “[408]–[410] Flexible Ringing Assignment — Day/
Night/Lunch”.
SelectionEnable(A CO button indicator will flash when a call is received.
An extension user can answer the call by pressing the
flashing button.)
Disable(A CO button indicator lights when a call is received, but
an extension user cannot answer the call.)
DefaultEnable
Programming1.Enter 109.
Display: CO Indicator
2.Press NEXT.
Display example:Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferencesNone 
						

							4-34 System Programming
4.2 System Programming
Flash Key Mode
110
DescriptionAssigns sending a flash signal when the FLASH button on a
proprietary telephone is pressed.
SelectionMODE 1(A flash signal is sent during the time programmed in
program “[418] Flash Time”)
MODE 2(A flash signal is sent while the FLASH button is
pressed.)
DefaultMODE 2
Programming1.Enter 110.
Display: Flash Key
2.Press NEXT.
Display example:MODE 1
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• For MODE 2, a flash signal will be sent for the programmed time in
program [418] if the FLASH button is pressed for less than the
programmed time.
Feature ReferencesSection 3, Features
External Feature Access
Flash 
						

							4.2 System Programming
Hold Music Selection
111
System Programming  4-35
DescriptionUsed to determine the music source use for Music on Hold for
outside calls.
SelectionExternal / Tone
DefaultExternal
Programming1.Enter 111.
Display: Hold Music
2.Press NEXT.
Display example:External
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Conditions• The external music source is a user-supplied item. One music source can
be installed.
• If “Tone” is assigned, the following cyclic tone is sent to the held
outside (CO) line.
Feature ReferenceSection 3, Features
Music on Hold
1 s 
						

							4-36 System Programming
4.2 System Programming
DSS Console Indication Mode
112
DescriptionEnables or disables the Busy Lamp Field (BLF) on DSS buttons to
indicate the Forward (FWD) or Do Not Disturb (DND) status of
corresponding extensions.
SelectionEnable(FWD/DND — flashing)/ Disable(FWD/DND — off)
DefaultEnable
Programming1.Enter 112.
Display: DSS Indication
2.Press NEXT.
Display example:Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferenceSection 3, Features 
DSS Console (KX-T7040) 
						

							4.2 System Programming
Extension Ringing Pattern Selection
115
System Programming  4-37
DescriptionSelects the extension ringing pattern when an intercom call is
received.
The ringing patterns are shown below.
SelectionSingle / Double / Triple
DefaultDouble
Programming1.Enter 115.
Display: Ext Ring pattern
2.Press NEXT.
Display example: Double
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Conditions• The extension ringback tone is the same as the pattern assigned in this
program.
• The programs [423] “Outside (CO) Line Ringing Pattern Selection” and
[706] “Doorphone Ringing/Tone Pattern Selection” should be
considered when assigning this program.
Feature ReferenceSection 3, Features 
Ringing Pattern Selection for Intercom Calls and Outside (CO) Lines
1 s
Single:
Double:
Triple: 
						

							4-38 System Programming
4.2 System Programming
Call Pickup Tone
117
DescriptionEnables or disables the confirmation tone sent when the Call pickup
feature is activated.
SelectionEnable / Disable
DefaultEnable
Programming1.Enter 117.
Display: Call Pickup Tone
2.Press NEXT.
Display example: Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferencesSection 3, Features 
Call Pickup, Directed
Call Pickup, Group 
						

							4.2 System Programming
Pulse Restriction
118
System Programming  4-39
DescriptionEnables or disables sending pulse dialing to the Central Office
during a conversation with an external party, when Pulse or Call
block is selected in program [401] “Dial Mode”.
SelectionEnable / Disable
DefaultEnable
Programming1.Enter 118.
Display: Pulse Restrict
2.Press NEXT.
Display example: Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferencesNone 
						

							4-40 System Programming
4.2 System Programming
Redialing After Pulse to Tone Conversion
119
DescriptionEnables or disables sending tone dialing to the Central Office when
an extension user redials after changing from pulse to tone mode by
pressing and #.
SelectionEnable / Disable
DefaultDisable
Programming1.Enter 119.
Display: Redial After  #
2.Press NEXT.
Display example: Disable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferenceSection 3, Features 
Pulse to Tone Conversion 
						

							4.2 System Programming
Toll Restriction Check for  and #
125
System Programming  4-41
DescriptionAssigns whether the entered “ ” and “#” are checked by toll
restriction or not. This assignment is required for certain Central
Offices to prevent toll fraud. Some Central Offices ignore the
user-dialed “ ” and “#”. If the user’s Central Office ignores these
symbols, select “Disable”.
SelectionEnable(check)/ Disable (does not check)
DefaultEnable
Programming1.Enter 125.
Display: TRS Check for  #
2.Press NEXT.
Display example: Enable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
ConditionsNone
Feature ReferenceSection 3, Features
Toll Restriction 
						

							4-42 System Programming
4.2 System Programming
Voice Mail 1 APT Port for KX-TVS50 †
130
DescriptionEnables or disables the extension jack numbers 07, or 07 and 08
corresponding to the voice mail APT ports for data transmission to
the Panasonic Voice Processing System (KX-TVS50).
Selection• Port 7 / Port 7 & 8 / Disable
DefaultAll jacks — Disable
Programming1.Enter 130.
Display: VM1(APT)Port
2.Press NEXT.
Display example: Port:Disable
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• To change the current assignment from “Port 7” to “Port 7 & 8”, first it
must be changed to “Disable”. Likewise, to change it from “Port 7 & 8”
to “Port 7”, first it must be changed to “Disable”. If the current
assignment is already “Disable”, making a change can be done in one
step.
• When “Port 7 & 8” is selected in this program, following programs are
automatically set as described below.
[600] Extension Group Assignment: 
extension jack number 07 — extension group 7
extension jack number 08 — extension group 7
[100] Hunting Group Set: extension group 7 — Enable
[101] Station Hunting Type: extension group 7 — Circular
[102] Voice Mail Port for KX-TVS75/KX-TVS100: 
extension jack number 07 — Enable
extension jack number 08 — Enable
• If “Enable” is assigned in program [103] “DTMF Integration for
KX-TVS75/TVS100”, “Port 7” or “Port 7 & 8” cannot be selected.
• The extension jacks assigned as the voice mail APT ports in this
program are automatically set the Data Line Security.
Feature ReferenceSection 3, Features 
Voice Mail Integration for KX-TVS50
† Available when the KX-TA624 is connected to a Proprietary Telephone capable Panasonic Voice Processing System (one that
supports APT Integration; KX-TVS50).