Lucent Technologies DEFINITY Enterprise Communications Server, System 75, System 85 Instructions Manual

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-15 The MDW 9000 Wireless Telephone
18
nThe radio module has Power, Pass, and Radio indicator lights, a top hook,
card edge, and snap lock which connect the radio module to the carrier
assembly/backplane, an antenna, and power plug and line connectors.
In order to provide you with the freedom of mobility, the MDW 9000 is not
connected physically (by a line cord or wire from the handset) to the DEFINITY
Communications System Generic 1, Generic 2, or Generic 3, or the DEFINITY
ECS. Instead, the MDW 9000 communicates by way of a radio link to its matched
radio module, which, in turn, connects it to the DEFINITY switch or the DEFINITY
ECS. The telephone needs merely an electrical outlet, and a test check to make
sure that the handset is in range of its matching radio module.
The handset communicates through a matching radio module. When up to six
wireless phones are used within a single location, a carrier assembly is required.
When the radio modules are placed in the carrier assembly, it is considered a
radio base station.
Applications
The MDW 9000 Wireless Telephone can be used with the DEFINITY
Communications System Generic 1, Generic 2, and Generic 3, the DEFINITY
ECS, System 75, and System 85.
Physical Features
Dimensions
NOTE:
The dimensions described here for the MDW 9000 telephone are
approximate.
For the Handset:
Width = 1.5 inches
Length = 10 inches
Height = 2.43 inches
For the Cradle:
Width = 3.94 inches
Length = 9.75 inches
Height = 5.13 inches 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-16 The MDW 9000 Wireless Telephone
18
For the Radio Module:
Width = 5.5 inches
Length = 12.1 inches
Height = 1.5 inches
Handset Features
Fixed Feature Buttons
The MDW 9000 has the following eight fixed feature buttons:
nCONFERENCE button — labeled CONF
nDROP button — The DROP button is NOT labeled. It is located in the lower
right corner of the LCD display.
nTRANSFER button — labeled TRANS
nHOLD button
nFEATURE button — The Feature button (labeled FEAT) is not used.
nMUTE button — The MUTE button is used to turn on and off the
microphone associated with the handset
orthe headset.
nHeadset On/Off button — This button is used for turning the headset on
and off. Located on top of the handset, it is used when the headset jack is
in use. At all other times, the Headset On/Off button is deactivated to
prevent accidental call termination.
nHandset (labeled ON/OFF) button — This On/Off button is used for turning
the handset on and off. (It can also be used to turn the headset on or off.)
Outside Line or Intercom/ Programmable Feature Buttons
When labeled with an extension number, these buttons indicate lines used for
incoming and outgoing calls (call appearances) and for using the telephone as an
intercom; when programmed and labeled with feature names, these buttons
access features (feature buttons).
LCD Display
The display provides information on the status of lines and range, batter y power,
mute usage, etc. (See “Display Information” later in this section.)
Dial Pad
This is the standard 12-button pad for dialing telephone numbers and accessing
features. 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-17 The MDW 9000 Wireless Telephone
18
Volume Control Switch
The Volume control adjusts the receiver volume (higher or lower) when the
handset is off-hook and adjusts the ring volume (higher or lower) when the
handset is on-hook.
Antenna
The antenna is used for receiving the transmissions from the radio module. This
antenna is flexible and is permanently attached to the handset.
Battery Charging Contacts
These contacts are used for charging the handset when contact is made with the
charging cradle.
Headset Jack
This jack is used for connecting the headset to the handset.
Charging Cradle Features
Charge Indicator
The green Charging Indicator light on the cradle’s faceplate indicates when the
handset battery is charging. This LED is labeledCharge.
Spare Charge Indicator
The green Charge Indicator light on the cradle ’s faceplate indicates when the
spare battery (in the spare battery garage) is charging. This LED is labeled
Spare Charge.
Battery Charging Contacts
The battery charging contacts are used for charging the handset when contact is
made with the charging cradle.
Handset Hook
This hook is used for hanging up the handset in the cradle.
Spare Battery Cover
The battery cover covers the spare battery garage. It opens by sliding to the left.
Modular Power Pack
This rechargeable, replaceable batter y pack provides at least 3 hours of “talk time”
and should hold its charge for at least 22 hours. The power pack is located inside
the cradle. 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-18 The MDW 9000 Wireless Telephone
18
Power Cord Jack
This jack is used for connecting the power cord to your charging cradle. This cord
is then plugged into a wall outlet. This jack is located on the back of the cradle.
Radio Module Features
Power and Pass Indicator Lights
The Power and Pass lights indicate when the module is powered up and
completes its self-diagnostic. The Radio light goes on when the handset is in use.
Top Hook and Card Edge
The top hook and the card edge connect the radio module to the carrier
assembly/backplane mounting rod.
Snap Lock
This lock locks the radio module into the carrier assembly.
Antenna
The sturdy and flexible antenna sends signals between the handset and the radio
module.
Power Plug Jack
The AC adapter should be inserted into this jack.
Line Jack
The line cord should be inserted into this jack.
Display Information
The LCD Display provides visual call and telephone status information through
thefollowingsetoficons:
noror shows the status of the adjacent button. If the triangle
and rectangle both appear, you are using that line; if only the rectangle
appears, the line is in use.
n18appears during Local Test Mode;0through10can appear during the
Wireless Test Mode.
nONappears when the handset is on.
nRANGEflashes to indicate that you are out of range and appears steadily
when you have lost communication.
nPisnotused with a DEFINITY switch or System 75 or System 85.
nMUTEappears when the handset microphone is muted. 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-19 The MDW 9000 Wireless Telephone
18
nTappears when the Wireless Test Mode is active.
nMSGappears when there is a message waiting for you.
nBATTappears when the battery is low.
Out-of-Range Indication
While the set is still active, it gives an audible indication (double beep) and visual
indication (theRANGEicon appears on the LCD display) when the handset is
getting out of range of the radio module.
Distance and Installation Limitations
The MDW 9000 uses radio transmissions to communicate. The range depends on
your particular operating environment. For indoor use, intervening walls will
reduce the phone’s range. Try to stay away from concentrations of structural
metal, such as steel and aluminum, or reinforced concrete.
At least 6 feet is required between the radio module/radio base station and the
phone system switch.
Before you install the radio module or radio base station, note the following
considerations:
nWhen positioning the radio module or radio base station, try to place the
unit in a central location, relative to the handset usage area. If your switch
is located in a distant area, you may have to run line cord from your phone
system to the centrally positioned radio module(s). The maximum distance
is 1000 feet of 26 gauge cable.
nThe radio module or radio base station should not share the same power
line or be within 6 feet of equipment with microprocessors such as
answering machines, personal computers, and fax machines, or
electromagnetic equipment such as electric motors.
nFor remote locations, an individual radio module can be installed in that
area and attached via line cord to the phone system. IROBs should be
used in outdoor area.
nThe radio module or radio base station should be placed high on the wall
for optimum voice quality and range. Allow at least 1 foot of space between
the top of the antenna on the radio module(s) and the ceiling.
nInstall the single radio module within 3 feet of either side of, and within
6-8 feet above, a properly grounded 3-prong electrical outlet that is not
controlled by an on/off switch.
nInstall the radio base stations within 15 feet of either side of, and within
6-8 feet above, a properly grounded 3-prong electrical outlet that is not
controlled by an on/off switch. 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-20 The MDW 9000 Wireless Telephone
18
nIf your phone system uses an uninterruptible power supply, such as a
backup generator, be sure to connect the radio or radio base station to that
power supply.
Switch Administration
Aliasing
For all System 75 and System 85 releases and DEFINITY Generic 1, Generic 2,
and Generic 3, Versions 1 and 2, the MDW 9000 terminal must be administered
as a 7303S Hybrid terminal.
If your MDW 9000 is connected to a DEFINITY Generic 3, Version 3 (or later), the
MDW 9000 can be administered as itself.
For the System 85, R2V1 through R2V4 switch which does not accommodate
Universal modules, an ANN17B Hybrid pack in conjunction with a DS-1 carrier
must be used to connect the switch and the MDW 9000 terminal. On all other
switches, including System 75, a DEFINITY Generic 1 and Generic 3, or a
DEFINITY ECS, a TN62B Hybrid pack must be used with the Universal carrier for
this pur pose.
NOTE:
A DEFINITY Generic 2 may use either an ANN17B or a TN62B pack. In
either case, the latest vintage packs are recommended.
Button Numbering
Only the system manager should administer feature button assignments on the
telephone. It is recommended that you not use a feature that requires visuals (that
is, the light next to each administrable button) to be updated while the set is turned
off, or any feature that may be activated by button depression while the set is
turned off (for example, Send All Calls).
Use Figure 18-8 for button numbering on the MDW 9000 set when it is connected
to a System 75, a DEFINITY Generic 1, Generic 3 switch, or a DEFINITY ECS.
Use Figure 18-9 for button numbering on the MDW 9000 set when it is connected
toaSystem85oraDEFINITYGeneric2.
NOTE:
On System 75, a DEFINITY Generic 1 and 3, or a DEFINITY ECS, button
numbering begins with “1,” the button on the upper right of the display. On
System 85 and a DEFINITY Generic 2, button numbering star ts
with “3.” 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-21 The MDW 9000 Wireless Telephone
18
Figure 18-8. Button Numbering for an MDW 9000 Connected to a System 75,
a DEFINITY Generic 1 or 3, or a DEFINITY ECS
Figure 18-9. Button Numbering for an MDW 9000 Connected to a
System 85 or a DEFINITY Generic 2
FCC Registration
The MDW 9000 telephone has been tested and has been found to comply with
FCC Par t 15 Rules.
Hearing Aid Compatibility
This wireless telephone is compatible with inductively-coupled hearing aids.
ON
RANGEPMUTE
MSG
BATT
321
5 4 DRO P
10
ON
RANGEPMUTE
MSG
BATT
543
7 6 DRO P
10 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-22 The MDW 9000 Wireless Telephone
18
UL and CSA Approval
This voice terminal has been tested and has met the Underwriters Laboratories
(UL) Standards UL 1459 and have also met the Canadian Standards Association
(CSA) Standards CSA-C22.2 No.225-M90.
MDW 9000 Equipment PECs and Comcodes
The MDW 9000 telephone and components can be ordered with these PECs and
Comcodes:
nMDW 9000 Telephone (sold separately)
Black = PEC: 3204-01B
Comcode: 107017022
White = PEC: 3204-01B
Comcode: 107017030
nMDW 9000 Multiple Unit (sold as a unit)
Black = PEC: 3204-W1B
Comcode: 107077444
White = PEC: 3204-W1W
Comcode: 107077463
nCarrier Assembly/Backplane
PEC: 3204-CR1
Comcode: 107073330
nHeadset
PEC: 3122-041
nBattery Pack
Black = PEC: 32036
Comcode: 106760804
White = PEC: 32034
Comcode: 106760812
nHolster
Gray
Comcode: 846628527
Black
Comcode: 846501401
n8-foot Line Cord
Comcode: 103786794
nCharging Cradle
Black = PEC: 107076754
White = PEC: 107076762
nCarrier Assembly
Comcode: 107073330 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-23 The MDW 9000 Wireless Telephone
18
nCarrier Assembly AC Adapter
Comcode: 847224227
nRadio Module AC Adapter
Comcode: 847180890
nCharging Cradle AC Adapter
Comcode: 847180890
Additional Documents
The following documents contain additional information relating to the MDW 9000
Wireless Telephone: (Use the 9 digit number listed after each document to order
that book from the BCS Publications Center for Lucent Technologies.)
nDEFINITY Generic 1, 2, and 3, System 75 and System 85 MDW 9000
Wireless Telephone User’s Guide
, 555-230-768
nMDW 9000 Wireless Telephone Installation Manual, 503-801-111
nMDW 9000 Wireless Telephone Quick Reference, 503-801-110 
						

							DEFINITY Enterprise Communications Server and System 75 and System 85
Terminals and Adjuncts Reference
555-015-201Issue 11
December 1999
Cordless and Wireless Telephones
18-24 The MDW 9031DCP Wireless Pocket Phone
18
The MDW 9031DCP Wireless Pocket 
Phone
Figure 18-10. The MDW 9031DCP Wireless Pocket Phone
Redial
Feat/P
Conf
Tra n s
HoldMenu
Mute
123ABC DEF
456JKL MNO GHI
789T UV WXYZ PQRS
0OPER
Antenna
Receiver
Handset display
with Backlighting
Column buttons
MMute button
Select button
Dial pad
Headset connector Hold button Transfer button Conference buttonFeature/Program
buttonOn/Off buttonRedial button Volume controlLanyard loop Headset On/Off button
On/Off