Land Rover Defender Accessory Fitting Rover Manual

							STC 50255DEFENDER
6 6/
/8
8
15
12
x2
M16x40
14
16
x1
13
Ø13mmX2
M12x70
x2
810
11
x2
9
M16x40
x2
M16x40
M10x25
x1
x2
7STC 50255DEFENDER
5 5/
/8
8
5
6
M10x25
x2
x1
? 
						

							2925244Nm
244Nm
244Nm
40-50Nm
2830
STC 50255DEFENDER
8 8/
/8
8
24
x2
M10x45
26
56Nm
244Nm
75Nm
27
56Nm
75Nm
244Nm
x2
M10x45
STC 50255DEFENDER
7 7/
/8
8
23
2220
19
18
x1
M16x40
17
x1
M12
M12
x1
M12x70
21
x1
M16x40 
						

							DEFENDER
WARNING
Accessories which are not properly fitted can be dangerous. Read the
instructions carefully prior to fitting. Whilst fitting, comply with the
instructions at all times.  If in doubt, contact your nearest Land Rover
Dealer.
ACHTUNG!
Nicht sachgemäß montiertes Zubehör kann gefährlich sein.  Lesen Sie die
Montageanleitung sorgfältig, bevor Sie das Teil montieren. Halten Sie sich
bei der Montage an die Anleitung. Bei Unsicherheiten wenden Sie sich
bitte an Ihren Land Rover Händler. 
AVERTISSEMENT
Les accessoires qui ne sont pas correctement montés risquent d’être dan-
gereux. Veuillez lire soigneusement les instructions avant d’effectuer la
pose. Respectez toujours les instructions en cours de pose. En cas de doute,
consultez votre concessionnaire Land Rover local.
AVVERTENZA
Gli accessori non sistemati come previsto possono essere pericolosi.
Leggere attentamente le istruzioni prima del fissaggio.  Durante il montag-
gio seguire sempre le relative istruzioni.  In caso di dubbio rivolgersi al più
vicino concessionario della Land Rover.
AVISO
Aquellos accesorios que no hayan sido ajustados debidamente pueden
resultar peligrosos. Lea las instrucciones detenidamente antes de iniciar el
montaje.  Durante el motaje siga las instrucciones en todo momento.  En
caso de duda póngase en contacto con su Concesionario de Land Rover.
ADVERTÉNCIA!
Os Acessórios que não são montados adequadamente podem ser perigosos.
Leia as instruções cuidadosamente antes de montar. Durante a montagem,
obedeça as instruções todo o tempo. Se tiver alguma dúvida, contacte o
Concessionário LandRover mais próximo.
WAARSHCUWING
Accesoires die niet op de juiste wijze zijn gemonteerd kunnen gevaar
opleveren. Lees zorgvuldig de instructies alvorens met de montage te
beginnen. Houd u tijdens de montage te allen tijde aan de instructies. Neem
bij twijfel contact op met de dichtstbijzijnde Land Rover dealer. 
FITTING INSTRUCTION
Audio System
EINBAUANLEITUNG
Audiosystem
INSTRUCTION DE MONTAGE
System Autoraio-Stereo
ISTRUZIONI PER LUSO
Impianto Audio
INSTRUCCIONES DE MONTAJE
Sistema De Audio
INSTRUÇOES DE MONTAGEM
Sistema De Audio
MONTAGEHANDLEIDING
Audiosysteem
FITTINGINSTRUCTIONNo. STC 7764 FITPART No. STC 7764   Issue No. 1
A AC
CC
CE
ES
SS
SO
OR
RI
IE
ES
S 
  
						

							STC 7764 AUDIO SYSTEM DEFENDER
3
LAND ROVER ACCESSORIES
2
LAND ROVER ACCESSORIES
STC 7764 AUDIO SYSTEM DEFENDER
X2
X2X2
Ø 13mm
Ø 100mm
13mm
IMPORTANT INFORMATIONThis installation manual is divided into 7 language sections.  
ENGLISH ..............................................................................................................................Page 4IMPORTANT INFORMATIONCe manuel dinstallation est divisé en 7 sections de langues différentes
FRANÇAIS..........................................................................................................................Page 12WICHTIGE INFORMATIONDieses Einbauanleitung ist in 7 Abschnitte in je einer Sprache unterteilt.  
DEUTSCH ..........................................................................................................................Seite 20INFORMAZIONE IMPORTANTEQuesto Manuale di installazione èstato redatto in 7 lingue.  
ITALIANO ............................................................................................................................Pag 28INFORMACIÓN IMPORTANTEEste manual de instalación está divididoen 7 secciones de idioma.
ESPAÑOL ........................................................................................................................Página 36INFORMAÇÃO IMPORTANTEEste manual de instalação está dividido em 7 secções de idiomas diferentes.
PORTUGUÊS ..................................................................................................................Página 44BELANGRIJKE INFORMATIEDeze inbouwhandleiding is verdeeld in zeven hoofdstukken met 
elk een afzonderlijke taal.
NEDERLANDS ............................................................................................................Pagina 52
Ø 16mm
Ø 3mmØ 2mm
X8
STC 7763STC 7764STC 7765
X8
GBDFEIPNL
X2 
						

							STC 7764 AUDIO SYSTEM DEFENDER
5
LAND ROVER ACCESSORIES
DOOR SPEAKERS - Both sides15 Remove door check strap cover - 1 screw.
16 Measure and mark A post as shown and drill a
ø3mm pilot hole.
17 Measure and mark lower the A post cover as
shown and drill a ø3mm pilot hole through the
lower A post cover, insulation and into the A
post.
18 Drill out top hole on the A post to ø13mm.
19 Drill out the bottom the hole to ø16mm
20 Remove swarf, de-bur and paint exposed
metal with LR touch-up paint.
21 Remove 3  screws from lower A post cover.
22 Remove cover, disconnect interior light switch
and pull back insulation to expose lower A
post.
23 Prize open caps and remove door handle - 2
screws.
24 Using a small screwdriver carefully remove
spring clip from window winder
25 Carefully remove door locking knob surround
26 Remove door lever surround - 1 screw.
27 Remove 2 fixings from door panel.
28 Carefully remove door panel by releasing fir
tree fixings.
29 Position the speaker bezel (supplied in kit) on
door panel, locating the tabs in the panel
grooves
30 Mark the speaker aperture and 4  fixings holes.
31 Remove speaker bezel and drill 4 ø2mm screw
holes.
32 For the speaker aperture use ø100mm  hole
cutter.
33 Drill a ø16mm hole on the end  of the door
panel to correspond with the ø16mm hole on
the lower A post. 
4
LAND ROVER ACCESSORIES
STC 7764 AUDIO SYSTEM DEFENDER
DISARMING ALARM SYSTEMTo disarm the alarm system, turn the ignition
switch to position 2, and then back to 0. This will
allow you 15 seconds to disconnect battery.PREPARATION1 Prize out screw cover and remove grab handle
- 2 screws. 
2 Remove both air vent covers - 2 screws each. 
3 Release instrument binicle - 4 screws.
4 Remove driver ’s instrument panel - 2 screws.
5 Release heater control panel - 2 screws.
6 Remove dash top panel - 5 screws.
7 Remove centre instrument panel  - 2 screws,
nuts 4 washers. 
8 Remove centre dash cowel - 2 screws.
9 Remove fuse box cover - 2 thumb screws.
10 Remove dash finisher rail - 3 screws.
11 Remove wiper motor cover - 3 screws.
12 Remove inner dash panel by carefully disen-
gaging fir tree fixings - 2 large, 5 small. 
13 Remove upper wiper motor cover.
14 Remove dash tray.OPTIONAL DOOR SPEAKERS This section is for fitment of optional door speak-
ers STC 7765.
If speakers are not to be fitted skip this section
and go to the ‘Dash Speaker ’ section on page 7
1
23
28
26
29
33
2524
21
2
12
57
6
15
16
17
11
10
14
13
9
3
4
8
27
45mm10mm 
						

							STC 7764 AUDIO SYSTEM DEFENDER
7
LAND ROVER ACCESSORIES
DASH SPEAKERS 
Passenger side12 Position speaker  spacer on the wiper motor
cover so the narrowest part of the taper is
uppermost and central.
13 Mark the fixing holes and speaker aperture.
14 Remove speaker spacer and drill 4 screw
holes ø 2mm
15 For the speaker aperture use ø100mm  hole
cutter.
16 Remove swarf, de-bur and paint exposed
metal work with LR touch-up paint.DASH SPEAKERS
Drivers side17 Position the speaker spacer centrally on the
lower dash panel with the narrowest part of
the taper  uppermost.
18 Mark the speaker aperture/fixing holes.
WARNING:
19Prior to drilling the speaker aperture and fix-
ing holes, check that all wires behind the dash
panel are moved aside (access through dri-
ver ’s instrument. panel aperture)
20 Drill 4 screw holes ø 2mm and the speaker
aperture to ø100mm  with hole cutter.
21 Remove swarf, de-bur and paint exposed
metal work with LR touch-up paint.DASH SPEAKER HARNESS1 Locate the Dash Speaker Harness (supplied in
kit) and position the 8 way connector above
the centre instrument panel.Optional Door Speaker Connections2 Remove the anti back-out and connect the
Door Speaker Harness pins (if to be fitted) to
the Dash Speaker Harness connector as
shown.
6
LAND ROVER ACCESSORIES
STC 7764 AUDIO SYSTEM DEFENDER
34 Fit 4 spire clips (supplied in kit) over screw
holes on door panel
NOTE:
Trim the rear face of the door panel to fit.DOOR SPEAKER HARNESS1 Locate the Door Speaker Harness (supplied in
kit) and position the 4 connector pins above
the centre instrument panel.
2 Route the pink and pink/black wires across
the dash, through the instrument binicle and
down to the drilled hole in the lower A post.
Feed the wire through the ø13mm hole and
out of the ø16mm hole.
3 Route the yellow and yellow/black wires
across the dash panel to the lower LH A post.
Feed the wire through the ø13mm hole and
out of the ø16mm hole.
4 Route the speaker wires through protective
sheathing (supplied in kit) and position the
sheathing in the two holes to avoid wire
chaffing (both sides).
5 Route the speaker wires through the insula-
tion and A post cover (both sides).
6 Refit A post cover, insulation and and interior
light switch using existing fixings (both
sides).
7 Reposition both door panels.
8 Route the speaker wire through the convolut-
ed grommet (supplied in kit), through the
ø16mm hole in the door panel and out
through the speaker aperture (both doors).
9 Refit door panel fixings and replace door han-
dle, door lever, window winder and locking
knob surround (both doors).
10 Attach the speaker wires to the speaker and
fit the bezel, speaker and grille to both door
panels with 4 screws (supplied in kit).
11 Fit the convoluted grommet to the door panel
and A post, ensuring a watertight fit (both
Doors).
34
1
3
2
2
4
13
14
17
2
19
34
8
11
Pink
Pink/Black Yellow/BlackYellow 
						

							`STC 7764/65- AUDIO STSTEM DEFENDER
9
LAND ROVER ACCESSORIES
POWER HARNESS1 Position the 8 way Power Harness connector
(supplied in kit) above the centre instrument
panel.
2 Locate orange/white wire with bullet connec-
tor on the Power Harness and connect the to
the orange/white wire (ignition feed) taped
back to the main vehicle harness at the centre
of the dash.
3 Locate the red wire (permanent feed) and
black wire (earth) on the Power Harness and
route through lower dash to the fuse box area.
4 Connect the black wire to the screw securing
the fuse box.
5 Locate the purple wire (permanent feed) on
the main vehicle harness exiting the fuse box.
6 Cut the purple wire and attach 2 male bullet
connectors.
7 Fit both ends of the purple wire to either end
of the double bullet connector (supplied in
kit).
8 Fit the red wire on the Power Harness to the
double bullet connector.
9 Insulate the red/orange wire and tape back to
the harnessHEAD UNIT10 Refit dash tray.
NOTE:
Ensure the two 8 way connectors and aerial
connector are routed through hole.
11 Reposition the dash inner panel and refit fir
tree fixings.
12 Position the Radio Housing centrally on the
dash and mark both fixing holes.
13 Remove housing and drill both holes to
ø5mm.
NOTE:
Drill through both dash tray and bulkhead.
14 De-bur and treat exposed metal work with LR
touch up paint.
8
LAND ROVER ACCESSORIES
STC 7764 AUDIO SYSTEM DEFENDER
DASH SPEAKER HARNESS
Continued3 Route the brown/white and black dash
speaker wires to the drivers side through the
instrument binicle and down to the speaker
aperture.
4 Attach the wires to the speaker and fit the
speaker and spacer to the dash panel with 4
screws (supplied in kit).
5 Route the brown/black and black dash speak-
er wires along the dash tray to the wiper
motor .
NOTE:
Refitting the wiper motor cover will be car-
ried out after the refitting the dash panels.AERIAL The aerial will be fitted to the drive de front wing
(RHD shown).
6 Measure and mark wing as shown
7 Drill a ø2mm pilot hole and using a hole cut-
ter enlarge to ø25mm.
8 De-bur and paint exposed metal with LR
touch up paint.
9 Fit the aerial from under the wing and secure
with its fixings.
10 Fit the aerial clip to the top of the inner wheel
arch bracket - screw, washer and locut nut
(supplied in kit). 
11 Secure the bottom of the aerial to the clip and
route up to the bulkhead grommet.
12 Make a small incision and route the wire
through the grommet to the centre instrument
panel.
NOTE:
Ensure the grommet has a water tight fit.
5
4
9
10
12
10
195mm
55mm
Ø25mm
6
3
2
6
8
7
12
12 
						

							10
LAND ROVER ACCESSORIES
STC 7764 AUDIO SYSTEM DEFENDER
15 Cut an access hole in the centre instrument
cowel as shown.
16 Refit cowel to the dash with existing fixings.
and route the two 8 way connectors and aerial
through the aperture.
17 Fit the radio cage to the housing (supplied in
kit) and bend the tabs on each side to secure.
18 Reposition the radio housing and route the
two 8 way connectors and aerial through the
apertute.
19 Insert radio mounting bung (supplied in kit)
to the rear of the radio housing.REFIT1 Attach the speaker wires to the passenger ’s
speaker and re-fit the wiper motor cover to
the dash panel with 3 screws.
2 Ensure the lower wiper motor cover is located
correctly in the slot of the upper wiper motor
cover.
3 Refit dash finisher rail - 3 screws.
4 Refit fuse box cover - 2 thumb screws
5 Refit centre instrument panel  and secure
instrument cowel - 2 screws, nuts and 4 wash-
ers.
6 Refit dash top panel - 5 screws.
NOTE:
Ensure radio housing lip is secured under
dash panel.
7 Secure radio housing  - 2 fir tree fixings
8 Refit heater control panel - 2 screws.
9 Refit driver ’s instrument panel - 2 screws.
10 Refit instrument binicle - 4 screws.
11 Refit  air vent covers - 2 screws each.
12 Refit grab handle - 2 screws plus cover.
13 Fit the two 8 way connectors and aerial to the
head unit and slide into the housing. Press in
firmly.
14 Reconnect battery.
RADIO OPERATION
Refer to user manual for operation and security
code.
15172
18
18
19 
						

							SYSTEME AUTORADIO-STEREO STC 7764 DEFENDER
13
ACCESSOIRES LAND ROVER
HAUT-PARLEURS DE PORTE - Les deux côtés15 Retirer le couvercle de la bride de retenue de porte
(1 vis).
16 Mesurer et marquer le montant A comme indiqué
sur le schéma, puis percer un trou pilote à un ø de
3mm.
17 Mesurer et marquer le recouvrement  du montant
A inférieur comme indiqué sur le schéma, puis
percer un trou pilote à un ø de 3mm dans le recou-
vrement du montant A inférieur, l’isolation et dans
le montant A.
18 Percer le trou supérieur du montant A jusqu’à un
ø de 13mm.
19 Percer le trou inférieur jusqu’à un ø de 16 mm.
20 Eliminer les ébarbures, ébavurer et recouvrir le
métal dénudé d’une couche de peinture de
retouche LR.
21 Retirer les 3 vis du recouvrement du montant A
inférieur,
22 Retirer le recouvrement, débrancher le commuta-
teur de l’éclairage de l’habitacle et rabattre l’isola-
tion pour exposer le montant A inférieur.
23 Déclipser les caches et retirer la poignée de porte 
(2 vis).
24 A l’aide d’un petit tournevis, retirer le collier à
ressort de la manivelle de lève-vitre.
25 Retirer avec précaution le pourtour du bouton de
blocage de la porte.
26 Retirer le pourtour du levier de porte (1 vis).
27 Retirer les 2 fixations du panneau de porte. 
28 Retirer avec précaution le panneau de porte en
dégageant les agrafes “sapin”.
29 Placer le cuvelage du haut-parleur (fourni dans le
kit) sur le panneau de porte, en introduisant les
languettes dans les rainures du panneau.
30 Marquer la découpe du haut-parleur et percer 4
trous de fixation. 
31 Retirer le cuvelage du haut-parleur et percer 4 trous
pour vis d’un ø de 2mm.
32 Pour l’ajourage pour haut-parleur, utiliser un cutter
à trou pour un ø de 100mm.
33 Percer un trou d’un ø de 16mm à l’extrémité du
panneau de porte pour le faire correspondre au trou
d’un ø de 16mm prévu sur le montant inférieur A.
23
28
26
29
33
2524
16
17
27
45mm10mm
12
ACCESSOIRES LAND ROVER
SYSTEME AUTORADIO-STEREO STC 7764 DEFENDER
DESARMEMENT DU SYSTEME
D’ALARMEPour désarmer le système d’alarme, tourner la clé de
contact à la position 2 puis revenir à 0. Vous disposez 
alors de 15 secondes pour débrancher la batterie.PREPARATION1 Extraire le cache-vis et retirer la manette (2 vis).
2 Déposer les couvercles des deux buses de prise
d’air (2 vis chacun).
3 Dégager la visière instruments (4 vis).
4 Déposer le tablier instruments du conducteur
(2 vis).
5 Dégager le panneau de commande du chauffage
(2 vis).
6 Déposer le panneau supérieur de la planche de
bord (5 vis).
7 Déposer la partie centrale du tablier instruments
(2 vis, 2 écrous, 4 rondelles).
8 Déposer la joue d’auvent centrale de la planche de
bord (2 vis).
9 Déposer le couvercle de la boîte à fusibles
(2 vis à ailettes).
10 Déposer la barre de finition de la planche de bord
(3 vis).
11 Déposer le couvercle du moteur d’essuie-glace
(3 vis).
12 Déposer le panneau intérieur de la planche de
bord. Pour cela, dégager avec précaution les
agrafes “sapin” (2 grosses, 5 petites).
13 Déposer le couvercle supérieur du moteur
d’essuie-glace. 
14 Déposer le bac de la planche de bord.HAUT-PARLEURS DE PORTE EN
OPTIONCette section décrit la pose des haut-parleurs de
porte STC 7765 en option.
S’il n’est pas prévu de poser de haut-parleurs,
omettre cette section et passer à la section 
“Haut-parleurs dans planche de bord” à la page 7.
1
21
2
12
57
6
15
11
10
14
13
9
3
4
8