Hitachi F 2500 Manual

							1 - 12 
(6)  On completion of initialization, the window shown in   
Fig. 1-10 is displayed.   
 
 
 
Fig. 1-10 
1.3    Startup of FL Solutions Program  
						

							1 - 13 
1.4  Screen Composition  
 
This manual contains multiple methods for executing a function.   
For implementing each method, explanation is given using the 
naming described below.     
 
(1)  Menu bar and Command   
 
Menu bar is a bar on which menus such as “File (F)” and 
“Edit (E)” are arranged.    Commands are contained in each 
menu.   
In the case shown in Fig. 1-11, an expression of “Scan (S) 
command of Spectrophotometer (S) menu” is used.     
A menu or command is selectable by 2 methods.   
•  Move the mouse pointer to a menu and click on it.   
•  Key in the alphabetic letter after a menu name with the 
Alt key held down.    Then, key in the alphabetic letter 
after a command name.   
 
 
 
Fig. 1-11    Menu Bar and Command 
 
  1.4.1  Basics of Window 
Operation 
Menu bar 
 
Command 1.4.1  
						

							1 - 14 
(2)  Toolbar and Tool button   
 
Toolbar is a row of tool buttons such as          and tool 
buttons provide shortcuts for common menu commands.     
In using    , it is expressed as “     button of 
Measurement toolbar” or “     (analytical condition) 
button.”  
For details of each button, refer to 1.4.4.   
 
 
 
 
 
Fig. 1-12  Toolbar 
 
 
Toolbars 
 
1.4  Screen Composition 
  
						

							1 - 15 
(3) Dialog box  
 
When you click the          button of Measurement toolbar, a 
small window as shown in Fig. 1-13 is presented.     
This window is called a “dialog box.”   
 
 
 
Fig. 1-13  Dialog Box 
 
 
(4) Tab  
 
Tabs are used in the Analysis Method window or Property 
window.  
Click a tab for changing display.    Each tab contains setting 
items.    The display shown in Fig. 1-14 is expressed as 
“Instrument tab.”   
 
 
 
 
Fig. 1-14 
Tabs 
1.4.1  
						

							1 - 16 
(5) Spin button  
 
This button is used for inputting a numeral.    Click   
or     for setting a numeral.  However, a value below 
decimal point cannot be set.    Such a value must be input 
with the keyboard.   
 
 
Fig. 1-15    Spin Button and Combo Box 
 
 
(6) Combo box  
 
Selection is allowed among the predetermined conditions.   
Click    for selecting the desired condition.  
 
(7) Check box  
 
For turning on a check box, put a check mark in it by 
clicking.  
The check box is then set in the      status.   
For turning off the check box, click it again to remove the 
check mark.   
 
 
Fig. 1-16  Check Box 
Combo box 
Spin button 
Check box 
 
1.4  Screen Composition 
 
 
 
  
						

							1 - 17 
The FL Solutions program have two kinds of windows; monitor 
window and data processing window.     
Set the monitor window active for measurement, or the data 
processing window for data processing.   
The toolbar differs between these windows.   
 
Fig. 1-17  Monitor Window 
 
 
 
 
Fig. 1-18    Data Processing Window 
 
  1.4.2  Kinds of Windows 
1.4.2  
						

							1 - 18 
The items displayable in each measurement mode are shown 
below.   
 
(1) Wavelength Scan  
 
A spectrum alone can be displayed or both spectrum and 
peak table can be displayed as shown in Fig. 1-19.   
Display of the peak table can be turned ON/OFF from the 
View menu.   
 
 
 
Fig. 1-19  Wavelength Scan 
 
 
(2) Time Scan  
 
A spectrum alone can be displayed or both spectrum and 
kinetics result table can be displayed as shown in Fig. 1-20.   
Display of the kinetics result table or peak table can be 
turned ON/OFF from the View menu.   
 
 
Fig. 1-20    Time Scan (kinetics)  1.4.3 Data Processing 
Window  
Peak table  Spectrum 
Peak table Spectrum    1.4  Screen Composition  
						

							1 - 19 
 
Fig. 1-21    Time Scan (peak table) 
 
 
(3) Photometry  
 
The items shown in Fig. 1-22 are selectively displayed 
depending on measurement method.   
 
•  On measurement starting with calibration curve   
 
 
 
Fig. 1-22 
 
 
Calibration 
curve data  Calibration 
curve Sample data  Standard data 
Peak table  Spectrum   1.4.3  
						

							1 - 20 
•  On generation of calibration curve through factor input   
 
 
 
Fig. 1-23 
 
 
•  On display of photometric value at each wavelength in 
multi-wavelength mode   
 
 
 
Fig. 1-24 
 
 
Calibration 
curve factor Sample data 
Sample data  1.4  Screen Composition  
						

							1 - 21 
The FL Solutions program provides five kinds of toolbars as 
shown below.    You can select a command by pulling down each 
menu from the menu bar.    But for quick and easy operation, it is 
advisable to use these tool buttons.     
 
• Standard Toolbar  
Has buttons related to printing and file handling.   
 
 
 
 
•  Instrument Toolbar (displayed in monitor window)   
Has buttons related to spectrophotometer control such as 
wavelength drive and baseline measurement.   
 
 
 
 
•  Measurement Toolbar (displayed in monitor window)   
Has buttons related to measurement such as analysis method 
setting and sample name input.     
 
 
 
 
•  Spectrum Toolbar (displayed in data processing window)   
Has buttons related to spectral display such as auto scaling, 
ruled line indication and spectrum tracing.   
 
 
 
  1.4.4 Explanation of 
Tool Buttons   
 
1.4.4