Fujitsu Fi6130 Operators Manual

							
  
Unit: mm
    
 
 HINT 
When [Check Overrapping(Ultrasonic)] is selected, the multifeed detect\
ion ratio may drop if 
the document sheet(s) are glued or electrostatically adhered to each o\
ther.
    
 Setting Example 3 (Bad Example)
   
Selected range=Enable, Start=100mm, End=102mm
    
  
Unit: mm
    
* Since the detection range (length) is less than the minimum value (\
5 mm), the Multifeed Detection cannot be performed 
correctly.
     
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 8.5 Page Edge Filler
 
 
 
Depending on the state of the documents, the shadow of the scanned docum\
ent appears in the end portion of the output image 
and black thin lines may be generated. 
If this is the case, you can improve the output image by using the “P\
age Edge Filler” function. This function fills the end portion 
of the image so that it looks clean.
Configure the settings for the Page Edge Filler as follows: 
 
1.  Start up the Software Operation Panel.
 See Section 8.1 Scanner Settings.
  
2.  Select [Device Setting 2] from left side list in the window, and select \
[Paper Edge Filter (ADF)]  from its lower level. 
  
 
  
3.  Specify the length for each end section; top, bottom, right, and left, t\
o fill the end sections.
   
						

							
 
 ADF FB
T: Top edge=0 to 15 mm Top edge=0 to 15 mm
D: Bottom edge=–7 to 7 mm Bottom edge=0 to 15 mm
R: Right edge=0 to 15 mm Right edge=0 to 15 mm
L: Left edge=0 to 15 mm Left edge=0 to 15 mm
  (can be set in increments of 1 mm) (can be set in increments of 1 mm)
   
 The specified areas are filled with white when the backing (background)\
 is white, and with black when the backing is 
black.
   
 
 
 HINT 
Unless otherwise specified, the background color is white. You can also \
change it to the 
“Black background” using the scanner driver. 
If you are using the TWAIN driver, do the following to change the backgr\
ound color to black: 
Select the [Option] button, and then select [Black background] from [Aut\
omatic Size and 
Skew detection] on the [Rotation] tab.
    
 
 ATTENTION
 
Note that if the Page Edge Filler is too wide, some characters in the vi\
cinity of the boundary 
may be cut out. 
     
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 8.6 Dropout Color
 
 
 
 
By using the “Dropout Color” function, you can scan documents with\
 the specified color removed from the light’s three primary 
colors, or red, green, blue. (This function is available for the binary\
 black and white setting as well as the grayscale setting.) 
For example, you can scan only the black part of letters when scanning t\
he document containing black letters each with a green 
frame.
Configure the settings for the Dropout Color as follows: 
 
1.  Start up the Software Operation Panel.
 See Section 8.1 Scanner Settings.
  
2.  Select [Device Setting 2] from left side list in the window, and select \
[Dropout color] from its lower  level. 
  
 
  
3.  Select a color to drop out.
 Red, Green, Blue Red, green, or blue is dropped out.
None No dropout occurs.
  
						

							
 ATTENTION
 
l     The Dropout Color setting can also be configured using the scanner drive\
r setting 
window. (The scanner driver setting window is given a priority over Sof\
tware Operation 
Panel.)
l     When configuring the setting through Software Operation Panel, you canno\
t select other 
colors than red, green, and blue. If you want to drop out any other colo\
rs, use the 
scanner driver setting window. 
For details on how to configure settings through the scanner driver sett\
ing window, see 
Section 
3.7 Excluding a Color from Images (Dropout Color).
 
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 8.7 Pre-Pick
 
 
 
To scan documents consecutively, you can previously pick the document to\
 be scanned next. This operation is called Pre-Pick. 
By enabling Pre-Pick, the time interval between the scanning of two sepa\
rate documents can be shortened. 
Configure the settings for the Pre-Pick as follows: 
 
1.  Start up the Software Operation Panel.
 See Section 8.1 Scanner Settings.
  
2.  Select [Device Setting 2] from left side list in the window, and select \
[Pre-Pick] from its lower  level.
  
 
  
3.  Select [Yes] or [No] for Pre-Pick.
 Select [Yes] to make Pre-pick valid, and select [No] to make it invalid.\
   
						

							
  HINT 
l     By enabling Pre-Pick, faster scanning can be achieved.
l     While Pre-Pick is valid, if you cancel scanning in process, you have to \
reload the 
document after ejecting all the pre-picked document.
l     This setting is also available by scanner driver setting. (In this case\
 scanner driver 
setting has a priority.)
     
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 8.8 Paper Feeding Retry Times
 
 
 
You can specify this feature to reduce the number of times paper feeding\
 (picking) is to be retried.
Configure the number of paper feeding retry times as follows. 
 
1.  Start up the Software Operation Panel.
 See Section 8.1 Scanner Settings.
  
2.  Select [Device Setting 2] from left side list in the window, and select \
[Number of paper feeding  retries] from its lower level.
  
 
  
3.  Specify the retry times from 1 to 12.
   
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 8.9 Life Counter Setting
 
 
 
This counter specifies the page count to ask the operator to replace the\
 consumables. When the page count exceeds the value 
specified here, the background color of the counter becomes yellow (see\
 Section 
5.2 How to Check and Reset the 
Consumables Counters), or a message (see the replacement message) appears.
Configure the settings for the life counter as follows. 
 
1.  Start up the Software Operation Panel.
 See Section 8.1 Scanner Settings.
  
2.  Select [Device Setting 2] from left side list in the window, and select \
[Useful life counter] from its  lower level.
  
 
  
3.  Specify the counter value to change its color for each consumable (Pick\
 roller, Brake roller).
 Setting is available from 10,000 to 2,550,000 with 10,000 increment.
   
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 8.10 Setting for Timeout for Manual Feeding
 
 
 
In Manual Feeding where you manually load documents sheet by sheet, you \
can scan multiple batches of documents 
continuously as a single file when you load the second stack of document\
 before the timeout time after loading the first batch.  
The scanning terminates automatically when the time has elapsed, canceli\
ng the Manual Feeding. 
You can cancel the Manual Feeding immediately by pressing the [Send to] \
button within the timeout period specified. 
Configure the settings for the Timeout for Manual Feeding as follows:
 
1.  Start up the Software Operation Panel.
 See Section 8.1 Scanner Settings.
  
2.  Select [Device Setting 2] from left side list in the window, and select \
[Manual-feed timeout] from  its lower level.
  
 
  
3.  Select whether to enable or disable the Timeout for Manual Feeding. When\
 enabling the timeout, select the timeout period for manual feeding until loading the next docu\
ment after the previous 
one.