Fujitsu Fi6130 Operators Manual
Have a look at the manual Fujitsu Fi6130 Operators Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 86 Fujitsu manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 136
4. Remove the Brake roller from the shaft.
5. Attach a new Brake roller.
Insert the shaft to the Brake roller aligning the shaft tab with the slo\
t of the Brake roller.
Brake rollers slot
Shaft tab
6. Attach the Brake roller to the scanner.
Attach the Brake roller to the scanner in reverse order of removing.
1)Set the left side of the shaft into place first, then fix the right side\
of the shaft.
2)Close the Brake roller cover.
7. Close the ADF....](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-135.png "Page 136
4. Remove the Brake roller from the shaft.
5. Attach a new Brake roller.
Insert the shaft to the Brake roller aligning the shaft tab with the slo\
t of the Brake roller.
Brake rollers slot
Shaft tab
6. Attach the Brake roller to the scanner.
Attach the Brake roller to the scanner in reverse order of removing.
1)Set the left side of the shaft into place first, then fix the right side\
of the shaft.
2)Close the Brake roller cover.
7. Close the ADF....")
![Page 138
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
5.4 Replacing the Pick Roller
1. Remove any documents from the ADF paper chute.
2. Remove the ADF paper chute from the scanner.
ADF paper chute
3. Open the ADF by pulling the ADF open lever and turning the ADF to the fr\
ont.
ADF open lever
CAUTION
Be careful, the ADF may close and pinch your finger.
4. Remove the Pick roller from the scanner.
1) Use the handle in the middle of the...](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-137.png "Page 138
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
5.4 Replacing the Pick Roller
1. Remove any documents from the ADF paper chute.
2. Remove the ADF paper chute from the scanner.
ADF paper chute
3. Open the ADF by pulling the ADF open lever and turning the ADF to the fr\
ont.
ADF open lever
CAUTION
Be careful, the ADF may close and pinch your finger.
4. Remove the Pick roller from the scanner.
1) Use the handle in the middle of the...")
![Page 139
Sheet guide
2) Rotate the Pick roller lever in the direction of the arrow.
Lever
3) Slide the Pick roller in the direction of teh arrow, and then lift i\
t up to remove the shaft from the hole.
CAUTION
Be careful not to touch the gear beside the lever of the Pick Roller as \
grease is applied to it.
5. Remove the Pick roller from the shaft.
Remove the Pick roller from the shaft while lifting up the tab on the Pi\
ck roller.](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-138.png "Page 139
Sheet guide
2) Rotate the Pick roller lever in the direction of the arrow.
Lever
3) Slide the Pick roller in the direction of teh arrow, and then lift i\
t up to remove the shaft from the hole.
CAUTION
Be careful not to touch the gear beside the lever of the Pick Roller as \
grease is applied to it.
5. Remove the Pick roller from the shaft.
Remove the Pick roller from the shaft while lifting up the tab on the Pi\
ck roller.")
![Page 140
Tab Pick roller Shaft
CAUTION
If you lift the pick roller tab with your fingernail, it may hurt your f\
ingernail. Use a
paper clip to lift the pick roller tab if you cannot do it with your fin\
ger.
6. Attach a new Pick roller.
Insert the new Pick roller aligning the screw on the shaft with the slot\
in the Pick roller.
Pick roller shaft Screw Slot Pick roller
ATTENTION
Make sure that the Pick roller is correctly attached. The incompletely-a\
ttached Pick roller...](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-139.png "Page 140
Tab Pick roller Shaft
CAUTION
If you lift the pick roller tab with your fingernail, it may hurt your f\
ingernail. Use a
paper clip to lift the pick roller tab if you cannot do it with your fin\
ger.
6. Attach a new Pick roller.
Insert the new Pick roller aligning the screw on the shaft with the slot\
in the Pick roller.
Pick roller shaft Screw Slot Pick roller
ATTENTION
Make sure that the Pick roller is correctly attached. The incompletely-a\
ttached Pick roller...")
![Page 141
2) Rotate the Pick roller lever in the direction of the arrow.
0 Lever
3) Close the sheet guide. Make sure that both sides of the side guide a\
re firmly locked.
8. Close the ADF. Press down on the center of the ADF to return it to its o\
riginal position until the ADF open leverlocks.
9. Attach the ADF paper chute to the scanner.
With the movie below, review the procedure to replace the Pick roller.](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-140.png "Page 141
2) Rotate the Pick roller lever in the direction of the arrow.
0 Lever
3) Close the sheet guide. Make sure that both sides of the side guide a\
re firmly locked.
8. Close the ADF. Press down on the center of the ADF to return it to its o\
riginal position until the ADF open leverlocks.
9. Attach the ADF paper chute to the scanner.
With the movie below, review the procedure to replace the Pick roller.")
![Page 143
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
Chapter 6 TROUBLESHOOTING
This chapter describes how to remedy document jams, other troubles, item\
s to check before contacting the agent where you
bought the scanner, and how to check device labels.
ATTENTION
For information about troubles that are not described here, and the deta\
ils of the errors, refer to
the FUJITSU TWAIN32 Scanner Driver Help.
All Rights Reserved. Copyright 2007 ©...](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-142.png "Page 143
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
Chapter 6 TROUBLESHOOTING
This chapter describes how to remedy document jams, other troubles, item\
s to check before contacting the agent where you
bought the scanner, and how to check device labels.
ATTENTION
For information about troubles that are not described here, and the deta\
ils of the errors, refer to
the FUJITSU TWAIN32 Scanner Driver Help.
All Rights Reserved. Copyright 2007 ©...")
![Page 144
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
6.1 Removing Jammed Documents
If a document jam occurred, follow the procedure below to remove the jam\
med documents.
ATTENTION
l Take care not to get injured when removing jammed documents.
l Be careful not to get neckties, necklaces, etc. entangled in the scanner\
when
removing the jammed documents.
l The surface of the glass and guides may become hot during operation. Tak\
e care not...](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-143.png "Page 144
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
6.1 Removing Jammed Documents
If a document jam occurred, follow the procedure below to remove the jam\
med documents.
ATTENTION
l Take care not to get injured when removing jammed documents.
l Be careful not to get neckties, necklaces, etc. entangled in the scanner\
when
removing the jammed documents.
l The surface of the glass and guides may become hot during operation. Tak\
e care not...")
![Page 145
Press center of ADF
ATTENTION
l Make sure that the ADF is completely closed. When it is not completely c\
losed,
feeding errors may occur.
l When the scanning is completed or canceled, the documents might remain i\
nside the
ADF even though any error message is not displayed.
Follow the procedure below to remove the documetns remaining in the ADF.\
1. Remove all documents from the ADF paper chute.
2. Open the ADF by pulling the ADF open lever toward you.
3. Remove the remaining...](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-144.png "Page 145
Press center of ADF
ATTENTION
l Make sure that the ADF is completely closed. When it is not completely c\
losed,
feeding errors may occur.
l When the scanning is completed or canceled, the documents might remain i\
nside the
ADF even though any error message is not displayed.
Follow the procedure below to remove the documetns remaining in the ADF.\
1. Remove all documents from the ADF paper chute.
2. Open the ADF by pulling the ADF open lever toward you.
3. Remove the remaining...")
![Page 146
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
6.2 Error Indications on the Operator Panel
When any error occurs, the operator panel indicates [J] or [U] and a num\
ber alternately for temporary errors, or [E], [F], [C],
[H], [A], or [L] and a number alternately for device alarms (permanent \
error). Temporary errors can be solved by the operator,
but the device alarm require recovery works by support engineers.
If you want to clear the error...](http://img.usermanuals.tech/thumb/26/59946/w64_fujitsu-fi6130-operators-manual-1488462901_d-145.png "Page 146
fi-6130 / fi-6230 Image Scanner Operators Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
6.2 Error Indications on the Operator Panel
When any error occurs, the operator panel indicates [J] or [U] and a num\
ber alternately for temporary errors, or [E], [F], [C],
[H], [A], or [L] and a number alternately for device alarms (permanent \
error). Temporary errors can be solved by the operator,
but the device alarm require recovery works by support engineers.
If you want to clear the error...")
2) Rotate the Pick roller lever in the direction of the arrow. 0 Lever 3) Close the sheet guide. Make sure that both sides of the side guide a\ re firmly locked. 8. Close the ADF. Press down on the center of the ADF to return it to its o\ riginal position until the ADF open leverlocks. 9. Attach the ADF paper chute to the scanner. With the movie below, review the procedure to replace the Pick roller.
10. Reset the Pick roller counter. For how to reset the Pick roller counter, see Section 5.2 How to Check and Reset the Consumables Counters. All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operators Guide TROUBLESHOOTING CONTENTS MAP TOP Chapter 6 TROUBLESHOOTING This chapter describes how to remedy document jams, other troubles, item\ s to check before contacting the agent where you bought the scanner, and how to check device labels. ATTENTION For information about troubles that are not described here, and the deta\ ils of the errors, refer to the FUJITSU TWAIN32 Scanner Driver Help. All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operators Guide TROUBLESHOOTING CONTENTS MAP TOP 6.1 Removing Jammed Documents If a document jam occurred, follow the procedure below to remove the jam\ med documents. ATTENTION l Take care not to get injured when removing jammed documents. l Be careful not to get neckties, necklaces, etc. entangled in the scanner\ when removing the jammed documents. l The surface of the glass and guides may become hot during operation. Tak\ e care not to get burned. 1. Remove any documents on the ADF paper chute. 2. Open the ADF by pulling the ADF open lever and turning the ADF to the fr\ ont. ADF open lever 000000 CAUTION Be careful, the ADF may close and pinch your finger. 00 3. Remove the jammed document. ATTENTION l Staples, paper clips, etc. cause document jams. Be sure to fully check t\ he document and feed path, and remove any small metal objects such as these. Also, before you start scanning, be sure to remove any staples, clips, e\ tc. from the document. l In case you have scanned stapled or clipped documents, do not pull them \ out forcibly. Otherwise, the glass and/or guides may be damaged. 4. Press down on the center of the ADF to return it to its original positio\ n and lock the ADF open lever.
Press center of ADF ATTENTION l Make sure that the ADF is completely closed. When it is not completely c\ losed, feeding errors may occur. l When the scanning is completed or canceled, the documents might remain i\ nside the ADF even though any error message is not displayed. Follow the procedure below to remove the documetns remaining in the ADF.\ 1. Remove all documents from the ADF paper chute. 2. Open the ADF by pulling the ADF open lever toward you. 3. Remove the remaining documents. 4. Close the ADF. All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operators Guide TROUBLESHOOTING CONTENTS MAP TOP 6.2 Error Indications on the Operator Panel When any error occurs, the operator panel indicates [J] or [U] and a num\ ber alternately for temporary errors, or [E], [F], [C], [H], [A], or [L] and a number alternately for device alarms (permanent \ error). Temporary errors can be solved by the operator, but the device alarm require recovery works by support engineers. If you want to clear the error indication, press the [Scan] or [Send to]\ button. The scanner will return to the Ready Status. Function Number Display [Function] Button When the Error Recovery Guide is installed on your computer, its window \ appears when Windows is started up. If any error or device alarm occurred, this software displays information such as error \ names and error codes regarding the error/alarm. Record the information and click [Details] on its window to learn detail\ ed information for troubleshooting. HINT The Error Recovery Guide is stored in the Setup CD-ROM. When installing \ the application software, refer to Section 2.3 Installing the Scanner Software in fi-\ 6130/fi-6230 Getting Started. Temporary Errors l Paper Feed Errors [J] and a number are displayed alternately.
IndicationMeaning Remedy J1 Paper jam 1. Remove the halted or jammed document remaining inside. For how to remove such documents, see Section 6.1 Removing Jammed Documents. 2. Confirm that the documents meet the paper conditions for scanning from the ADF. For details see Chapter 7 ADF AND SPECIFICATIONS. J2 Multifeed error Pressing the [Send to] button on the Operator Panel ejects the mutifed document. l Cover Open, Print, and Other Errors [U] and a number are displayed alternately. Indication Meaning Remedy U0 Transport lock error (fi-6230 only) Unlock the transport lock. For details refer to 2.1 Installing the Scanner in fi-6130/fi-6230 Getting Started. U4 The ADF opened during scanning. Close the ADF completely and load the document again. U5 The imprinter cover opened during scanning. (when imprinter option is installed in fi-6130) U6 The print cartridge of the imprinter option (for fi-6130 only) is not set. This is a temporary error related with the Imprinter option (sold separately). For details refer to 614PR Imprinter Operators Guide. Permanent Errors (device alarms) l Motor and Optical Systems [E] and a number are displayed alternately. Indication Meaning Remedy E0 Flatbed motor malfunction (fi-6230 only) 1. Confirm that the transfer lock is released. 2. When a device alarm is indicated, turn off and on the scanner. If the alarm is still displayed on the Function Number Display, record the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. E1 Optical system error (Flatbed). (fi-6230 only) E2 Optical system error (ADF front). When you encounter any alarm on the display, turn the scanner off and on. If the alarm is still displayed on the Function Number Display, record the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. E3 Optical system error (ADF back). E6 Operator panel error E7 Internal memory error (EEPROM) E9 Image memory error l Overruning [F] and a number are displayed alternately.
IndicationMeaning Remedy F4 Background switching mechanism error When you encounter this alarm on the display, turn the scanner off and on. If the alarm is still displayed on the Function Number Display, record the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. l Chips [C] and a number are displayed alternately. Indication Meaning Remedy C0 LSI error When you encounter this alarm on the display, turn the scanner off and on. If the alarm is still displayed on the Function Number Display, record the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. l Fuses [H] and a number are displayed alternately. IndicationMeaning Remedy H0 The motor fuse has blown out. When you encounter any alarm on the display, turn the scanner off and on. If the alarm is still displayed on the Function Number Display, record the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. H6 The imprinter fuse has blown out. (when imprinter option is installed in fi-6130) H7 The lamp fuse has blown out. H8 The background switching motor fuse has blown out. l Options (only when imprinter option is installed in fi-6130) [A] and a number are displayed alternately. Indication Meaning Remedy A0 Error in imprinters control board When a device alarm is indicated, turn the scanner off and on. If the alarm is still displayed on the Function Number Display, note down the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. A1 Communication timeout error in the imprinter A2 Error in imprinters ink head A3 Error in imprinters internal memory (EEPROM) A4 Imprinter ROM error l Sensor [L] and a number are displayed alternately.
IndicationMeaning Remedy L6 Ultrasonic sensor error When a device alarm is indicated, turn the scanner off and on. If the alarm is still displayed on the Function Number Display, record the indicated error code, and contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operators Guide TROUBLESHOOTING CONTENTS MAP TOP 6.3 Remedying Typical Troubles This section describes troubles that may occur during scanning and how t\ o remedy those troubles. Before you ask for repair, check the following flowcharts. If the remedi\ es in these flowcharts do not solve the problem, check the items in Section 6.4 Items to Check Before Contacting the Dealer Where You Bought the Sca\ nner and then contact the dealer where you purchased the scanner or an authorized FUJITSU scanner service\ provider. Scanner cannot be turned On. Indication on Function No. display goes out. The scanning does not start. Quality of scanned pictures or photos is not satisfactory when scanning \ in black and white. Quality of scanned text of lines is unsatisfactory. Images are distorted or blurred. Vertical lines appear in the scanned image. The Function Number display indicates alarm (with [E] or other alphabet\ ical letter plus a number) after the scanner is turned ON. Multifeed errors occur frequently. Pickup errors occur frequently. Paper jams occur frequently. The scanned images are elongated when scanned from the ADF. There is a shadow on the leading edge of the scanned images. All Rights Reserved. Copyright 2007 © PFU LIMITED