Fujitsu Fi6130 Operators Manual

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 Safety Precautions (3)
 
 
 
 1  2  3  4 
 
 CAUTION
Do not install the scanner on unstable surfaces.
Make sure that the scanner is installed on a flat, level surface and tha\
t none of its parts extend 
beyond the surface top, such as a desk or table. Do not install the scan\
ner on unstable surfaces. 
Install the scanner on a level surface that is free of vibration to prev\
ent it from falling.  
Install the scanner on a strong surface that will support the weight of \
the scanner and other devices.
  
 Firmly insert the power plug.
 
Firmly insert the power plug as far it can go into the power outlet.
 
Do not block the ventilation ports.
 
Do not block the ventilation ports. Blocking the ventilation ports gener\
ates heat inside of scanner, 
which may result in fire or scanner failure.
 
Do not place heavy objects or stand on top of the scanner.
 
Do not place heavy objects on the scanner or use the scanners surface t\
op to perform other work. 
Improper installation might cause injuries and equipment failure.
 
Do not use the scanner immediately after moving it from a cold place 
into a warm room.
 
Do not use the device immediately after moving it from a cold place into\
 a warm room. 
Condensation may occur, which might lead to scanning errors. Let the dev\
ice dry about one or two 
hours before you use it.
 
Before moving the scanner, disconnect the power plug from the power 
outlet.
 
Do not move the scanner with the power and interface cables connected as\
 this can damage the 
cables, which can later cause fire, electric shock as well as injury. 
Before moving the scanner, be sure to disconnect the power plug from the\
 power outlet, and all 
other interface cables. Make sure that the floor is free of any obstruct\
ions.
 
 
 1  2  3  4 
 
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 Safety Precautions (4)
 
 
 
 1  2  3  4 
 
 CAUTION
Protect the scanner from static electricity.
 
Install the scanner away from strong magnetic fields and other sources o\
f electronic noise. Also, 
protect the scanner against any static electricity, which can cause the \
scanner to malfunction.
 
Avoid any contact when scanner is in use.
 
Avoid getting a sleeve, necktie, or hair caught up in any scanner mechan\
ism during scanning since 
this may cause injuries. 
 
Disconnect the power plug from the power outlet when the scanner is 
not used for a long period of time.
 
When the scanner is not going to be used for a long period of time, be s\
ure to disconnect the power 
plug from the power outlet.
 
Do not install the scanner in direct sunlight.
 
Do not install the scanner under direct sunlight or near heating apparat\
us. Doing so might cause 
excessive heat to build up inside the scanner, which can cause scanner t\
rouble or even fire. Install 
the scanner in a well-ventilated location.
 
Before moving the scanner, make sure the transport lock is locked. (fi-\
6230 only) 
 
When moving the scanner, be sure to lock the transport lock in order to \
prevent damage to the 
scanner.
 1  2  3  4 
 
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
Chapter 1 NAMES AND FUNCTIONS OF PARTS
 
 
 
This chapter describes the scanner parts and their functions.
 
 
 
 
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 1.1 Checking the Contents of the Scanner Package
 
 
 
When you open the scanner package, please handle the main unit and its a\
ttachments carefully.  
Make sure it contains all the parts listed in the package contents list \
that is included in the package box. 
If any parts are missing or defective, contact the dealer where you purc\
hased the scanner or an authorized FUJITSU scanner 
service provider.
 
 
 
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 1.2 Names and Functions of Parts
 
 
 
This section describes the scanner parts and their functions. 
 Front
 
 
 
No. Name Function
1 ADF 
(Automatic Document Feeder) Transports the document to the reading position 
automatically.
2 ADF paper chute Holds in place the document pages / sheets that are fed 
into the ADF.
3 Paper chute extension 1
4 Paper chute extension 2
5 Side Guide Adjusted to the width of the paper in order not to scan 
skewed pages.
6 ADF open lever  Pull this lever toward you to open the ADF.
7 Operator panel This panel consists of a Function No. Display, four 
operating push buttons, and a LED. 
8 Stacker Scanned documents are ejected from the ADF onto this 
stacker.
9 Stacker extension 1  
[fi-6130 only]
10 Stacker extension 2  
[fi-6130 only]
11 Stacker extension  
[fi-6230 only]
12 Flatbed (FB) 
[fi-6230 only] Place documents on the glass sheet by sheet for single-
sheet scanning.
13 Transport lock switch  
[fi-6230 only] Used to lock the carrier unit inside the flatbed during 
transportation.
 
 Inside  
						

							
 
 
No. Name Function
1 Document bed  Place documents on the glass when scanning through the flatbed.
2 Document holding 
pad Holds documents down on the document bed.
3 Document cover Holds the documents loaded at the reading position when closed.
 
 
HINT 
The document cover with a black document holding pad is optionally avail\
able.  
This type is convenient for scanning documents in black background when \
loading them from 
the flat bed.
l     Name: Black Document Pad (fi-624BK) 
l     Parts No.: PA03540-D801 
 
 Rear 
 
 
No. Name
1 Security Slot
2 EXT connector (for imprinter connection) [fi-6130 only] 
3 USB connector 
4 DC inlet 
 Removable Parts 
						

							
Parts that can be removed from the scanner are displayed below. 
 
 
 
No. Name
1 ADF paper chute 
2 Pick roller 
3 Brake roller 
4 Document cover [fi-6230 only]
   
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 1.3 Functions of the Operator Panel
 
 
 
 
The operator panel is located on the right side of the scanner. This pan\
el is comprised of a Function Number display, four 
buttons, and a LED. 
 
 
 
No. Name Function
1 Check LED Lights when an error occurs.
2 Function Number Display Indicates the function number and error status.
3 Function Button Changes the Function activated by the Send to button (*).
4 Send to Button 
Launches the linked application software (*). 
Resets an error.
5 Scan/Stop Button
Launches the linked application software (*). 
Resets an error.  
Cancels ongoing scanning.
6 Power Button/LED Turns the scanner ON and OFF. 
Lights when the scanner is turned ON.
 
*) About the settings on the launcher, refer to FUJITSU TWAIN32 scanner dri\
ver help, which is included in the 
Setup CD-ROM, and Appendix 1 
Before Using the [Scan] or [Send to] Button.
 
 Indications on the Function Number Display
Indication Function
8 Blinks only one time upon turning on the scanner.
P Indicates that the scanner has been turned ON and is being initialized.
0 Indicates that initialization will soon end.
1 Indicates that initialization has ended successfully. This status is cal\
led Ready 
Status.
J 
U Indicates that a recoverable error occurred during scanning with the ima\
ge scanner.  
J or U and an error number is displayed alternately. 
When an error is indicated, press the [Scan] button or [Send to] button \
to return to 
the Ready Status (1).
E  F 
C 
H  A  L  Indicates that an abnormality (alarm) occurred in the image scanner du\
ring its 
initialization or during scanning documents. 
E, F, C, H, A, or L and an alarm number are displayed alte\
rnately. When 
the alarm number is displayed, press the [Scan] button or [Send to] butt\
on to return 
to the Ready Status (1). 
If this alarm occurs, turn the power off and on again. If the alarm cont\
inues after 
turning the power on again, contact the dealer where you bought the scan\
ner or an 
authorized FUJITSU scanner service provider. 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 Chapter 2 BASIC SCANNER OPERATIONS
 
 
 
This chapter describes basic scanner operations.
In this chapter Windows XP screenshots are illustrated. The screens and \
operations may differ slightly if the OS that you are 
using is other than Windows XP. 
Also, when the FUJITSU TWAIN32 or FUJITSU ISIS scanner driver is updated\
 the screens and operations noted in this chapter 
will differ slightly. In such case, refer to the relevant manuals or mat\
erials, which are to be supplied when updating the driver. 
 
 
 
 
All Rights Reserved. Copyright 2007 © PFU LIMITED 
						

							
fi-6130 / fi-6230 Image Scanner Operators Guide
 
 
 
TROUBLESHOOTING 
CONTENTS MAP 
TOP    
 
 2.1 Turning the Scanner ON 
 
 
This section describes how to turn the scanner ON. 
The following shows the procedure for turning the scanner ON.
 
 
1.  Press the Power button on the Operator Panel.
 
The scanner is turned ON, and the Power LED on the Operator Panel lights\
 in green.  
Also, while the scanner is being initialized, the indication of the Func\
tion Number Display changes as follows: 
8 -> P -> 0 -> 1  
The indication 1 means that the Operator Panel is in the Ready Status.\
 
 
 
 
Power 
button 
 
   HINT 
To turn the scanner OFF, hold the Power button down for at least two sec\
onds.
 
 About Power ON/OFF Control
 
You can select to power the scanner on/off either by pressing the Power \
button, or by connecting / disconnecting the AC 
cable.  
The procedure is as follows.
 
1.  Confirm if the scanner is connected correctly to the PC, then power on t\
he scanner. 
For details on how to connect the scanner to a personal computer, refer \
to section 2.2 Connecting the Scanner to 
Your PC of fi-6130/fi-6230 Getting Started.
  
 
2.  From the [start] menu, select [Control Panel].
The [Control Panel] window appears.