DELL 2155cdn User Manual

							Dell Printer Configuration Web Tool229
Va l u e s :
E-Mail Alert
Purpose:
To configure detailed settings for the E-Mail Alert. This page can also be 
displayed by clicking the E-Mail Alert in the left frame.
Va l u e s :
Host NameSets the host name of the server computer.
WorkgroupSets the workgroup.
Maximum SessionsSets the maximum number of sessions.
Unicode SupportSets whether to notify the host name and workgroup name in 
Unicode characters during SMB transmission.
Auto Master ModeSets whether to enable the Auto Master Mode.
Encrypt PasswordSets whether to encrypt the password.
Job Time-OutSets the job time-out period between 60 and 3,600 seconds.
Connection Time-OutSets the connection time-out period between 60 and 3,600 
seconds.
E-Mail Server 
SettingsPrimary SMTP 
GatewaySets the primary SMTP gateway.
SMTP Port 
NumberSets the SMTP port number. This must be 25, 587 
or between 5,000 and 65,535.
E-Mail Send 
AuthenticationSets the authentication method for outgoing e-
mail.
 
						

							230Dell Printer Configuration Web Tool
SMTP Login 
UserSets the SMTP login user. Up to 63 alphanumeric 
characters, periods, hyphens, underscores, and at 
symbols (@) can be used. If specifying more than 
one address, separate them using commas.
SMTP Login 
PasswordSets the SMTP account password using up to 31 
alphanumeric characters.
Re-enter SMTP 
Login PasswordConfirms the set SMTP account password.
POP3 Server 
Address
*1Sets the POP3 server address in IP address format 
of aaa.bbb.ccc.ddd or as a DNS host name using 
up to 63 characters.
POP3 Port 
Number
*1Sets the POP3 server port number. This must be 
110 or between 5,000 and 65,535.
POP User 
Name
*1Sets the POP3 account user name. Up to 63 
alphanumeric characters, periods, hyphens, 
underscores, and at symbols (@) can be used. If 
specifying more than one address, separate them 
using commas.
POP User 
Password
*1Sets the POP3 account password using up to 31 
alphanumeric characters.
Re-enter POP 
User Password
*1Confirms the set password.
Reply AddressDesignates the reply e-mail address sent with each 
E-mail Alert.
SMTP Server 
ConnectionDisplays the status of the SMTP server connection.
 
						

							Dell Printer Configuration Web Tool231
Bonjour (mDNS)
Purpose:
To configure the detailed settings of Bonjour.
E-Mail Alert 
SettingsE-Mail List 1Sets acceptable e-mail 
addresses for the E-Mail Alert 
feature using up to 255 
alphanumeric characters.
Select Alerts for 
List 1Supplies AlertsSelect the check box to receive 
an E-Mail Alert for 
consumables.
Paper Handling 
AlertsSelect the check box to receive 
an E-Mail Alert for paper 
handling.
Service CallSelect the check box to receive 
an E-Mail Alert for Service 
Calls.
E-Mail List 2Sets acceptable e-mail 
addresses for the E-Mail Alert 
feature using up to 255 
alphanumeric characters.
Select Alerts for 
List 2Supplies AlertsSelect the check box to receive 
an E-Mail Alert for 
consumables.
Paper Handling 
AlertsSelect the check box to receive 
an E-Mail Alert for paper 
handling.
Service CallSelect the check box to receive 
an E-Mail Alert for Service 
Calls.
*1This item is available only when POP before SMTP (Plain) or POP before SMTP 
(APOP) for E-Mail Send Authentication is selected.
Host NameSets the host name up to 63 alphanumeric characters and - (dash). 
The original setting will remain valid if no input is made.
 
						

							232Dell Printer Configuration Web Tool
SNMP
Purpose:
To configure the detailed settings of SNMP.
Va l u e s :
SNMP v1/v2c
Purpose:
To edit the detailed settings of SNMP v1/v2 protocol.
To enter this page, click Edit SNMP v1/v2 Properties in the SNMP page.
Va l u e s :
Printer NameSets the printer name up to 63 alphanumeric characters and symbol 
sets. The original setting will remain valid if no input is made.
SNMP 
ConfigurationEnable SNMP 
v1/v2c 
ProtocolSelect the check box to enable the SNMP v1/v2c 
protocol.
Edit SNMP 
v1/v2c 
PropertiesClick to display SNMP v1/v2c page and to edit the 
setting of SNMP v1/v2c protocol from the page.
Enable SNMP 
v3 ProtocolSelect the check box to enable the SNMP v3 
protocol.
Edit SNMP v3 
PropertiesClick to display SNMP v3 page and to edit the 
setting of SNMP v3 protocol from the page.
You can click this item only when SSL 
communication is enabled.
Community 
NameCommunity 
Name (Read 
only)
*1
Sets the community name to access (read only) data 
using up to 31 alphanumeric characters.
The original setting will remain valid if no input is 
made. Characters entered for community name in 
the previous settings will not be displayed on the 
screen. The default Read Community is public.
 
						

							Dell Printer Configuration Web Tool233
Re-enter 
Community 
Name (Read 
only)
*1
Enters the community name to access (read only) 
data again to confirm it.
Community 
Name 
(Read/Write)
*1
Sets the community name to access (read and write) 
data using up to 31 alphanumeric characters.
The original setting will remain valid if no input is 
made. Characters entered for community name in 
the previous settings will not be displayed on the 
screen. The default Read/Write Community is 
private.
Re-enter 
Community 
Name 
(Read/Write)
*1
Enters the community name to access (read and 
write) data again to confirm it.
Community 
Name (Trap)
*1Sets the community name used for trap up to 31 
alphanumeric characters.
The original setting will remain valid if no input is 
made. Characters entered for Community Name 
(Trap) in the previous settings will not be displayed 
on the screen. The default Trap Community is   
(NULL).
Re-enter 
Community 
Name (Trap)
*1
Enters the community name used for trap again to 
confirm it.
 
						

							234Dell Printer Configuration Web Tool
SNMP v3
Purpose:
To edit the detailed settings of SNMP v3 protocol.
To enter this page, click Edit SNMP v3 Properties in the SNMP page.
Va l u e s :
Trap 
Notification 1-4Trap Address 
Ty p e
Trap Address 
Port Number
NotifySelect the check boxes to notify trap occurrence. In 
this case, specify the IP address and IP socket in the 
following format:
IPv4
Specify the IP address and IP socket in the 
nnn.nnn.nnn.nnn:mmmmm format. Each section of 
nnn is a variable value between 0 and 255. Note 
that values 127 and 224-254 are not valid for the 
first three-digits only. IP socket mmmmm is a 
variable value between 0 and 65,535.
IPv6
Specify the IP address and IP socket in the 
xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:mmm
mm format. Each section of xxxx is a 
hexadecimal variable value between 0 and ffff. IP 
socket mmmmm is a variable value between 0 and 
65,535.
Authenticate 
Error TrapSelect the check box to notify Authenticate Error 
Trap.
*1The default value can be changed by using Dell Printer Configuration Web Tool.
 
						

							Dell Printer Configuration Web Tool235
Scan To PC
Purpose:
To specify the client when scanning data.
Va l u e s :
LLTD
Purpose:
To specify the maximum number of devices.
Administrator 
AccountAccount 
EnabledSelect the check box to enable the administrator 
account.
User NameEnters the user name of the administrator account.
Authentication 
PasswordSets the authentication password of the 
administrator account using 8 to 32 alphanumeric 
characters.
Re-enter 
Authentication 
PasswordConfirms the set password.
Privacy 
PasswordSets the privacy password of the administrator 
account using 8 to 32 alphanumeric characters.
Re-enter 
Privacy 
PasswordConfirms the set password.
Print Drivers / 
Remote Client 
AccountAccount 
EnabledSelect the check box to enable the print drivers and 
remote client account.
Reset to default 
PasswordClick to reset the password for the print drivers and 
remote client account to default.
FTP Client Connection 
Time-OutSets the connection time-out period from 1 to 60 
seconds.
FTP PassiveSets whether to enable the FTP Passive mode.
SMB Client Connection 
Time-OutSets the connection time-out period from 1 to 60 
seconds.
 
						

							236Dell Printer Configuration Web Tool
Va l u e s :
Wireless LAN
 NOTE: Wireless LAN feature is available only when the printer is connected 
using the wireless network.
Purpose:
To configure the detailed setting for the wireless network. 
To use the wireless adapter, be sure to disconnect the network cable.
 NOTE: Once wireless LAN is activated, wired LAN protocol will be disabled.
Va l u e s :
Maximum number of 
deviceSets the maximum number of device from 64 to 1,024.
Wireless 
SettingsSSIDSets the name that identifies the wireless network. 
Up to 32 alphanumeric characters can be entered.
Network TypeSets the network type from either Ad-Hoc or 
Infrastructure.
MAC AddressDisplays the MAC address of the wireless adapter 
for the printer.
Link ChannelDisplays the channel number of the wireless 
connection for the printer.
Link QualityDisplays the quality of the wireless network 
connection for the printer.
 
						

							Dell Printer Configuration Web Tool237
Security 
SettingsEncryptionSelect the security method from the list.
No SecuritySets No Security to configure 
the wireless setting without 
specifying a security method 
from WEP, WPA-PSK, and 
WPA-Enterprise.
WEPSets the WEP to use through 
the wireless network.
WPA-
PSK(WPA2-
PSK)
*1, 2
Sets the WPA-PSK to use 
through the wireless network.
WEP EncryptionSelect the WEP key code from either Hex or Ascii.
WEP Key 1Sets the WEP key set used through the wireless 
network only when WEP 128bit or WEP 64bit is 
selected for Encryption.
Re-enter WEP 
Key 1Enters the WEP key 1 again to confirm it.
WEP Key 2Sets the WEP key set used through the wireless 
network only when WEP 128bit or WEP 64bit is 
selected for Encryption.
Re-enter WEP 
Key 2Enters the WEP key 2 again to confirm it.
WEP Key 3Sets the WEP key set used through the wireless 
network only when WEP 128bit or WEP 64bit is 
selected for Encryption.
Re-enter WEP 
Key 3Enters the WEP key 3 again to confirm it.
WEP Key 4Sets the WEP key set used through the wireless 
network only when WEP 128bit or WEP 64bit is 
selected for Encryption.
Re-enter WEP 
Key 4Enters the WEP key 4 again to confirm it.
Transmit KeySets the transmit key type from the list.
WPA-PSK Pass PhraseSets the pass phrase.
Re-enter Pass 
PhraseEnters the pass phrase again to confirm it.
 
						

							238Dell Printer Configuration Web Tool
 NOTE: The optional wireless adapter supports WEP, WPA-PSK-TKIP, WPA-
PSK-AES, and WPA-PSK-AES.
Reset Print Server
Purpose:
To initialize NVRAM (non-volatile RAM) for the network feature and reboot 
the printer. You can also initialize NVRAM of the printer from Reset Defaults 
in the Printer Settings menu.
Va l u e s :
Security
The Security tab includes Set Password, LDAP Server, LDAP User 
Mapping, SSL/TLS, IPsec, 802.1x and IP Filter (IPv4).
Set Password
Purpose:
To set or change the password that is required to access the setup parameters of 
the printer from the Dell Printer Configuration Web Tool.
Set the password of the operator panel from Panel Lock in the Printer Settings. 
This page can also be displayed by clicking Set Password in the Left Frame.
 NOTE: To restore the password to the default (NULL), initialize the non-volatile 
memory (NVM).
Va l u e s :
*1For encryption, AES or TKIP method is used.*2This item is available only when the Infrastructure mode is selected for Network 
Ty p e .
Initialize NIC 
NVRAM Memory and 
restart printerClick the Start button to initialize NVRAM, revert network 
settings to the factory default settings, and reboot the network 
capability.
Restart PrinterClick the Start button to reboot the printer.
Administrator PasswordSets the password using up to 10 alphanumeric characters.