Home
>
Comdial
>
Communications System
>
Comdial DIGITECH Digital Telephone System Instructions Manual
Comdial DIGITECH Digital Telephone System Instructions Manual
Have a look at the manual Comdial DIGITECH Digital Telephone System Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 133 Comdial manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SYSTEM CONFIGURATION Mark the desired selections in the charts to record programming needs. Dial the feature code and then dial the selection code or press the programming button to program the selection. IOZE: A current program setting is indicated by a lighted LED next to fhe pmgramming button for fhaf selection.When a fcggfe (on/ofl) acfion is provided by a sing/e button, the lighted LED indicates an active feature. eEATURE DESCRIPTION base Level: The first step in any rogramming sequence is to enter the ase level. Once in this mode, any esired configuration can be set. Iystem Defauft: The system onfiguration features, described in ?e following procedures, can be lefautted to a standard set of values. ‘hese values will provide satisfactory ystem performance in a broad range If site applications. fnanswered Call Transfer Recall ‘Ime: A transferred call that remains Inanswered after a programmed ?ngth of time will return to the ransfening station for answering. ENTRY CODE AND PROMPTING DISPLAY Press ITCM Dial +# 7 4 6 +k 1. Dial 10.“SYSTEM DEFAULT” 2. Press #to default system features. 1. Dial 11.“TRANSFER RECALL ” 2. Dial 1 (sta xfr recall).“STA XFR RCL XXX ” -OR- Dial 2 (dept xfr recall).“DEPTXFR RCL XXX” 3. Choose transfer time. - Dial 1 or Press Al.5TA XFR RCL 70 ” - Dial 2 or Press A2.“STA XFR RCL 20 ” - Dial 3 or Press A3.“STA XFR RCL 25 ” - Dial 4 or Press A4.“STA XFR RCL 30 ” - Dial 5 or Press A5.“STA XFR RCL 45 ” - Dial 6 or Press A6.5TA XFR RCL 60 ” - Dial 7 or Press A9.“STA XFR RCL 90 ” - Dial 8 or Press AlO.‘STA XFR RCL 120 ” - Dial 9 or Press Al 1.‘STA XFR RCL 780 ” - Dial 0 or Press A12.“STA XFR RCL 400 ” 4. Press t for next transfer recall feature. 5. Press +k &for configuration mode.REFERENCE RECORD Press SPKR to end.
faPress ITCM +# # 7 4 6 +k for base level. FEATURE DESCRIPTION Recall/Flash: A line disconnect :recall) or a host system feature access signal (flash) can be generated depending upon the xogrammed time. Pause Tlme: During auto dials and speed dials, it is sometimes necessary to delay the sending of digits to give switching equipment time to prepare for receiving them. A pause is stored whenever the user presses the HOLD button. The pause length options are stored in seconds.ENTRY CODE AND PROMPTING DISPLAY 1. Dial 12“RECALUFLSH XXXX” 2. Select time. - Dial 1 or Press Al.“RECALUFLSH 0.08” - Dial 2 or Press A2.WECALUFLSH 0.30” - Dial 3 or Press A3.WECALUFLSH 0.50” - Dial 4 or Press A4.“RECALUFLSH 0.60” - Dial 5 or Press A5.“RECALUFLSH 0.75” - Dial 6 or Press A6.“RECALUFLSH 0.88” - Dial 7 or Press A9.“RECALUFLSH I ” - Dial 6 or Press AlO.“RECALUFLSH 7.50” - Dial 9 or Press Al 1.“RECALUFLSH 2 ” - Dial 0 or Press A12.“RECALUFLSH 3 ” 3. Dial +k for configuration mode. 1. Dial 13 “PAUSE TlME XXX n 2. Select time. - Dial 1 or Press Al.“PAUSE TIME 0.50 ” - Dial 2 or Press A2.“PAUSE TIME 1 ” - Dial 3 or Press A3.“PAUSE TIME 1.50 ” - Dial 4 or Press A4.“PAUSE TIME 2n - Dial 5 or Press A5.“PAUSE TIME 3- - Dial 6 or Press A6.“PAUSE TIME 5n - Dial 7 or Press A9.“PAUSE TIME 7.50 ” - Dial 6 or Press AlO.“PAUSE TIME 10 ” - Dial 9 or Press Al 1.“PAUSE TIME 15 n - Dial 0 or Press A12.“PAUSE TIME 20 ” 3. Dial +# for configuration mode.REFERENCE RECORD !II 3.0IDEFAULT = 2.0 sec. Press SPKR to end.
IPress ITCM +k # 7 4 6 t for base level.II1 FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAY ‘lmed Hold Recall: After a call has een on hold for a programmed mgth of time, the system will recall ie station that placed the call on old. The timing is in seconds. Iata Baud Rate: The speed or baud ate of the data bit stream, which :arries the SMDR and configuration lata between the system and an rxternal data device, must be jrogrammed to match the equirements of the data device.VOTE: If XMODEM p#tocol is to be used for data transfer between a VDT and the common equipment, 8-M data is required. 1. Dial 14“HOLD RECALL XXXX” 2. Select time. - Dial 1 or Press Al.“HOLD RECALL 30 w - Dial 2 or Press A2.“HOLD RECALL 60 ” - Dial 3 or Press A3.“HOLD RECALL 90 ” - Dial 4 or Press A4.“HOLD RECALL 120 ” - Dial 5 or Press A5“HOLD RECALL 180 ” - Dial 6 or Press A8.“HOLD RECALL 240 ” - Dial 7 or Press A9.“HOLD RECALL 300 ” - Dial 8 or Press AlO.“HOLD RECALL 360 w - Dial 9 or Press All.“HOLD RECALL 420 ” - Dial 0 or Press A12.“HOLD RECALL ” 3. Dial X for configuration mode. 1. Dial 15.‘BAUD RATE ” 2. Dial 1 for data port A. -OR- Dial 2 for data port B 3. Choose baud rate. Dial 01 or Press Al.“W nD nS 110” Dial 02 or Press A2.“W nD nS 150” Dial 03 or Press A3.“W nD nS 300” Dial 04 or Press A4.“W nD nS 600” Dial 05 or Press A5.“W nD nS 1200” Dial 06 or Press A8.“W nD nS 2400” Dial 07 or Press A9.“W nD nS 4800” Dial 08 or Press AlO.“W nD nS 9600” Dial 09 or Press Al 1.“W nD nS 19200” Dial 10 or Press A7 for 7 data bits and 2 stop bits.“W 70 25 ZZZZZ” Dial 11 or Press Al4 for 8 data bits and 1 stop bit. “W 8D 1S ZZZZZ” 4. Dial t for next data port. 5. Dial * +k for configuration mode.REFERENCE RECORD
Press ITCM % # 7 4 6 +# for base level. FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAY rone or Voice Slgnalllng: Intercom :alls can be tone signalled or voice signalled. The first choice in SignaIling is programmable. Delete Statlon Message Detall Accounting (SMDA) records by Attendant: When SMDA records exceed storage capacity, they must be deleted to make mom for more. The attendant can be allowed to delete these records if enabled by this programming step. DO Not Disturb (DND) Inhlblt: Any station can be set to a DND condition which cannot be overridden by a caller unless calling station is programmed for DND override. The DND feature can be disabled by this programming. NOTE: Also program a button as the DND button. See page 4-44.1. Dial 16.“XXXXX ANN. FIRST 2. Press Al to toggle between Voice To Tone. (LED On = voice signalling). -OR- Dial 1 for Voice First.“VOICE ANN. FIRST Dial 2 for Tone First.“TONE ANN. FIRST” 3. Dial * for configuration mode. 1. Dial 18. “ATTN DELETE XXX ” 2. Press Al to toggle between enable and disable (LED On = Enable). -OR- Dial 1 to Enable“ATTN DELETE ON u (Al LED On). Dial 2 to Disable “ATTN DELETE OFF ” 3. Dial k for configuration mode. 1. Dial 19.“DND XXXXXXXX w 2. Press Al to toggle between Enable and disable (LED On = Enable). -OR- Dial 1 to Enable“DND ENABLED ” (Al LED ON). Dial 2 to Disable. “DND DISABLED ” 3. Dial % for configuration mode.REFERENCE RECORD SIGNALLING 1 VOICE ITONEj DEFAULT = VOICEDISABLE 1 DEFAULT = DISABLE ID0 NOT DISTURB INHIBITi IENABLED IJDISABLED! DEFAULT = ENABLED Press SPKR to end.
- I Press ITCM f # 7 4 6 +k for base level.I :EATUFlE DESCRIPTION StatIon Monltorlng: The DSS/BLF at 1 station provides idle, busy and line inging status of monitored stations. If he flashing BLF lights associated with risual ring indication are deemed distracting, this visual indication can >e disabled system-wide. Call Park Recall Tlme: A call that is left in a parking orbit for a programmed length of time automatically returns to a timed hold recall condition at the parking station. Exclusive Hold: This feature prevents a held call from being retrieved at any other extension. It can be enabled or disabled system-wide. ENTRY CODE AND PROMPTING DISPLAY 1. Dial 20.“MONITOR XXXXXXX” 2. Press Al to toggle between enable and disable (LED On = Enable). -OR- Dial 1 to Enable“MONITOR ENABLED” (Al LED ON). Dial 2 to Disable.“MONITOR DISABLED” 3. Dial t for configuration mode. 1. Dial 22. “C. P. RECALL X ” 2. Select recall time: Program button LED On = Selected Time Press Al or dial 1 = 1 min. “C.P. RECALL X ” Press A2 or dial 2 = 2 min. Press A3 or dial 3 = 3 min. Press A4 or dial 4 = 4 min. Press A5 or dial 5 = 5 min. Press A8 or dial 6 = 6 min. Press A9 or dial 7 = Never Recall “NEVER RECALL” 3. Dial * for configuration mode. 1. Dial 23.“XXXXXXX EXC HOLD” 2. Press Al to toggle between enable and disable (LED On = Enable). -OR- Dial 1 to enable“ENABLE EXC HOLD ” (Al LED on). Dial 2 to disable.“DISABLE EXC HOLD” 3. Dial +% for configuration mode. REFERENCE RECORD 7STATION MONITORING ENABLED 1 DISABLD 1 DEFAULT = DISABLED Press SPKR to end.
4 i Press ITCM +k # 7 4 6 % for base level. 11 FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAYREFERENCE RECORD randem Attendant: When this1. Dial 24.“TANDEM ATTN XXX ” eature is enabled, a recall from an 2. Press Al to toggle between enable and disable Jnanswered call transfer or timed hold (LED On = Enable). vecall will ring at both attendant-OR-El stations. When disabled, only the Dial 1 to enable.“TANDEM ATTN OFF” attendant station which transferred :he call will ring.Dial 2 to disable (Al LED is on).“TANDEM ATTN ON n 3. Dial +# for configuration mode. Automatic Statlon Relocation: Wtth this feature, the system will automatically recognize a particular station should that station be re-located to a different station port, and supply the same COS parameters as programmed for the station at the original port. NOTE: Refer fo station fe-assignment1. Dial 27“AUTO STA RELOCAT” 2. Press Al to toggle between enable and disable (LED On = Enable) -OR- Dial 1 to Enable (Al LED On) Dial 2 to Disable 3. Dial +k for configuration mode. on page 4-51. System Alarm Reportlng: Special codes which convey certain system alarm conditions can be sent to a station where they will show on the LCD display. NOTE: Also, choose the alarm reporting stations. See page 4-35.1. Dial 28.“ALARM REPORTS ” 2. Press Al to toggle between enable and disable. (LED On = Enable) -OR- Dial 1 to enable. Dial 2 to disable. 3. Dial t for configuration mode. ALARM REPORTENABLE DISABLE DEFAULT = DISABLE Press SPKR to end.I
Press ITCM t # 7 4 6 f for base level.I :eature Inhlblt Programming: :ertain features can be disabled ystem-wide to provide a basic ?lephone system for use in lstallations where a large proportion If the stations are accessible to inauthorized users thus subject to ampering. These features are nabled when system default is betformed. . Dial 29. . Select feature.“FEATURE INHIBIT” - Dial 01 to disable Line Group 1. - Dial 02 to disable Line Group 2. - Dial 03 to disable Line Group 3. - Dial 04 to disable Line Group 4. - Dial 05 to disable Zone 1 Paging. - Dial 06 to disable Zone 2 Paging. - Dial 07 to disable Zone 3 Paging. - Dial 08 to disable All Call. - Dial 09 to disable Meet Me Page. - Dial 10 to disable Night Transfer. - Dial 11 to disable Background Music. - Dial 12 to disable Voice Announce Block. - Dial 13 to disable Message Waiting. - Dial 14 to disable Call Pickup. - Dial 15 to disable Call Forward. - Dial 16 to disable Automatic Call Back. - Dial 17 to disable Station-to-Station Messaging. - Dial 18 to disable Line Group Queue. - Dial 19 to disable Directed Station Hold. - Dial 20 to disable Call Park Orbit 1. - Dial 21 to disable Call Park Orbit 2. - Dail 22 to disable Call Park Orbit 3. - Dial 23 to disable Call Park Orbit 4. - Dial 24 to disable Call Park Orbit 5. - Dial 25 to disable Call Park Orbit 6. - Dial 26 to disable Call Park Orbit 7. - Dial 27 to disable Call Park Orbit 8. - Dial 28 to disable Call Park Orbit 9. - Dial 29 to disable Call Waiting. - Dial 30 to disable LCD Messaging. - Dial 31 to disable Executive Override/Service Observing. - Dial 32 to disable Account Code. - Dial 33 to disable Personal Call Forward - Dial 34 to Enable All Features. - Dial t for next item. - Dial * t for configuration ( DEFAULT = ALL ENABLED NOTE: Feature status is not conveyed via LED.
Press ITCM +k # 7 4 6 +k for base level. ‘A Options: The PA port can beRinging Issigned lines for direct ring, delayed1. Dial 60.‘P.A. OPTIONS ‘I ing, or night transfer (of ringing). The 2. Choose ringing assignment. art can also be arranged to receive Dial 1 for direct ring.“DIRECT RING ‘. fither zone or all-call paging. Dial 2 for delay ring.“DELAY RING ” Dial 3 for night ring.“NIGHT RING ”telay tracking of the enabled ringing 3. Select line ports: :an be selected as either station 17 inging or paging port ringing.Line port l-14 = Dial 01 - 14 or press Al - Al4 Line port 15,16 = Dial l&l6 or press Bl, 82 Line port 17-24 = Dial 17 - 24. or press HOLD then press Al - A8 NOTE: LEDS turn on when line is assigned. 4. Dial +K for next PA option. -OR- Dial ‘Ik % for configuration mode. Zone Paglng 1. Dial 60.“P.A. OPTIONS ” 2. Dial 4 to assign zone paging“PA ZONES n 3. Choose zone. Press Al or dial 1 for zone 1. Press A2 or dial 2 for zone 2. Press A3 or dial 3 for zone 3. Press A4 or dial 4 for all-call. NOTE: Al, A2, A3, or A4 LED turns on when a zone is assigned. 4. Dial +N for next PA option -OR- Dial +K + for configuration mode. Continued on next page
‘A Options - continuedContinued from previous page Rlnglng Tracking Relay1. Dial 60. “P.A. PORT ”2. Dial 5.“RELAY XXXXXXX” 3. Choose relay tracking assignment. Press Al to toggle between paging port and station port 17. (LED On = paging port) -OR-Dial 1 for station port 17. “RELAY STA. 17 ”Dial 2 for paging port.“RELAY P.A. PORT” 4. Dial +k for next PA option. -OR- Dial % t for configuration mode. Press ITCM +K # 7 4 6 * for base level. FEATURE DESCRIPTION Extended DTMF Tones For Automatic Dlallng: When a numberis automatically dialed (autodial, saved number redial, etc), the length of the generated DTMF tones are as set with this programming option. This is useful when the automatically dialed number is to be used to access answering machines, banking computers, voice mail, etc that require DTMF tones that are longer than standard tones.ENTRY CODE AND PROMPTING DISPLAY 1. Dial 26 “DliUF DIALNG XXXX” 2. Choose DTMF tone length - Press Al or dial 01 = 60 msec. - Press A2 or dial 02 = 80 msec. - Press A3 or dial 03 = 100 msec. - Press A4 or dial 64 = 120 msec. - Press A5 or dial 05 = 160 msec. - Press A6 or dial 66 = 240 msec. - Press A7 or dial 07 = 320 msec. - Press A8 or dial 66 = 400 msec. - Press A9 or dial 09 = 480 msec. - Press A10 or dial 10 = 560 msec. - Press All or dial 11 = 720 msec. - Press Al 2 or dial 12 = 880 msec. - Press Al3 or dial 13 = 1040 msec. 3. Dial t for configuration mode.REFERENCE RECORD
f 0 LINE CONFIGURATION1 Mark the desired selections in the charts to record programming needs.1 Dial the feature code and then dial the selection code or press the programming button to program the selection. JOTE: A current program setting is indicated b cra lighted LED next to the programming button for that selection.When a toggle (on/off) action is provided by a &g/e button, the lighteLED indicates an active feature.1 To make a line port selection, press a programming button or dial a selection number on the keypad as follows:LINE PROG. BUTTONSKEYPAD BUTTONS I- 14Al - Al401 - 14 15,16Bl, 8215,16 17 - 24HOLD plus Al - A817-24 NOTE HOLD button is used to toggle program buttons between lines 1 - 14 and 17 - 24. Llne Defautt: The line configuration features, described in the following procedures, can be defaulted to a standard set of values. These values will provide satisfactory system erformance in a broadrangeof site“LINE DEFAULT ” 2. Press #to default line features. System automatically returns to base level. Llne Disable: A line port canbe taken out of service because of defect or2. Select line ports to be disabled other reason. Return the line to service(LED On = Disabled). with the central office lines Line port 1-14 = Dial 01 - 14 or Press Al - Al4 programming procedure. Line port 15,16 = Dial 15,16 or press Bl, 82 Line port 17-24 = Dial 17 - 24 D then press Al - A8. 3.Dial % for configuration mo