Home > Comdial > Communications System > Comdial DIGITECH Digital Telephone System Instructions Manual

Comdial DIGITECH Digital Telephone System Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Comdial DIGITECH Digital Telephone System Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 133 Comdial manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							TAB091FEATUREBENEFIT
    ?rppott forWith software release 1 la, the DigiTech digital telephone system supports the use of the
    ,xecuMall voiceExecuMail voice processing system connected to the system’s station ports through the Comdialprocessing system
    ATI-D analog terminal interface.The ATI-D is a muttipurpose QB$QxB& accessory for the digital
    telephone system. It has dual circuits that allow the ExecuMail to interface to two station ports.
    Refer to Comdial publication 
    lMl89-037, lnsfallation Instructions For The Analog Terminal
    interface (AT/-D) for complete details for using the ATI-D to interface between the digital
    telephone system and the 
    BxecuMail system. In addition to the required programming task of
    identifying the ExecuMail station ports as voice mail ports, there are several other programming
    considerations associated 
    with the ExecuMail operation that the programmer can make whenever
    their options are wanted.
    VOICE MAIL PORT (Required)
    The programmer must identify the station ports where the installer has connected the ExecuMail
    system.Identifying them as voice mail ports enables the digital telephone system to recognize
    them as such for proper call handling.Use the following programming feature to enable the
    station port for ExecuMail operation.
    NOTE: The digital telephone system automatically disables this feature if an
    installer replaces the 
    AT/-D with a multiline telephone at the
    programmed station port.
    To program this feature, press ITCM +N # 7 4 6 +I+ then do the following steps:
    NOTE: The station that is being used for programming cannot be
    programmed as a voice mail port.
    1. Dial 63.“STATION FEATURES”
    2. Dial 32.“VOICE 
    MAlL PORT *
    3. Select station ports to be programmed:
    - station 1 1 - 57: Dial 11 - 67.
    4. Press SPKR to end.
    AUTOMATIC AlTENDANT (Optlon)
    With the automatic attendant feature, the ExecuMail system automatically answers any line that is
    ringing at a voice mail port. As a default, the system automatically enables ringing line
    preference for any port the programmer identifies as voice mail ports. The programmer must
    choose a ringing assignment for the lines assigned to the voice mail port before the ExecuMail
    system can provide the automatic attendant feature.
    To program this feature, press 
    ITCM * # 7 4 6 *then do the following steps:
    Direct Rlnglng
    1. Dial 64.“STMINE CONFIG”
    2. Dial 
    1.“DIRECT RING *
    3. Select line ports for direct ringing:
    -lineportl-14=DialOl -140rpressAl -A14,
    - line port 15,16 = Dial 1516 or press Bl, 82,
    - line port 17 - 24 = Dial 17 - 24 ( or press HOLD then press Al - A8).
    4. Dial # when all line ports are selected.
    Continued on next page . . .A 
    						
    							TAB091FEATURE
    BENEFIT
    Support for
    5. Select station ports to be programmed:
    ExecuMall voicestation 1 l- 57 = dial 11 - 57.processing system
    6. Dial +% when all station ports are selected.
    - continued7. Dial +k t for next station/line ringing assignment
    or press 
    SPKR to end.
    Delayed 
    Rlnglng
    1. Dial 54.“STA/LINE CONFIG.”
    2. Dial 2.“DELAY RING 
    -
    3. Select line ports for delayed ringing:
    - line port l-14 = Dial 01 - 14 or press Al - A14,
    - line port 1516 = Dial 1516 or press Bl, B2.,
    - line port 17 - 24 = Dial 17 - 24 (or press HOLD then press Al - A8).
    4. Dial # when all line ports are selected.
    5. Select station ports to be programmed:
    - station 1 l- 57: Dial 11 - 57.
    6. Dial ++G when all station ports are selected.
    7. Dial 
    +k ++G for next station/line ringing feature
    or press SPKR to end.Night Transfer (of 
    ringlng~
    1. Dial 54.
    2. Dial 3.
    3. Select line ports:
    “STAILINE CONFIG”
    “NIGHT RING”
    - line port l-14 = Dial 01 - 14 or press Al - A14,
    - line port 15,16 = Dial 1516 or press Bl, 82,
    - line port 17 - 24 = Dial 17 - 24 (or press HOLD then press Al - A8).
    4. Dial #when all line ports are selected.
    5. Select station ports to be programmed:
    - station 11 - 57: Dial 11 - 57.
    6. Dial + when all station ports are selected.
    7. Dial 
    ++ +k for next station/line ringing feature
    or press SPKR to end.
    AUTOMATIC TRANSFER OF 
    VOICE MAIL (Option)
    The programmer can choose the immediate transfer mode for voice mail transfers.However, if
    he turns on the screen 
    and/or confirm options provided by the ExecuMail system, he must not
    choose the immediate transfer mode because it allows the system to transfer a call as soon as it
    answers 
    it precluding any screen and confirm action that the ExecuMail can provide.
    To program this feature, press 
    ITCM * # 7 4 6 +k then do the following steps:
    1. Dial 25
    “V MAIL AUTO XFER”
    2. Press Al to toggle between enable and disable (LED On = Enable)or dial 1 
    to,enable (Al LED on) and dial 2 to disable.
    3. Press SPKR to end.
    Continued on next page . . .
    5 
    						
    							TAB091FEATUREBENEFIT
    ‘qlpport forHUNT GROUPS (Option)
    ,xecuMail voiceprocessing system
    When a station port that has been assigned to a hunt group is busy, a call to it will ring at the next
    - continuedidle station port in the group. A call will try to ring every port in a hunt group and if all are busy,
    the telephone system will return a busy tone to the caller.A programmer can assign all
    ExecuMail ports to a circular hunt group to take advantage of its multiple-port interface capability.
    Make a circular hunt group by linking all ExecuMail ports to one another and then linking the last
    ExecuMail port in the hunt group with the first ExecuMail port in the group.For example, with the
    ExecuMail connected at station ports 
    013,014,015, and 016, place port 013 in a hunt group and
    link 014 to it, then place 014 in a hunt group and link 015 to it, then place 015 in a hunt group and
    link 016 to it, and finially place 016 in a hunt group and link 013 to it to complete the circle. 
    With
    this arrangement, a call will first try to ring at port 013, then try port 014 and so forth until it trys all
    four ports.
    To program this feature, press 
    ITCM +# # 7 4 6 Q then do the following steps:
    1. Dial 53.“STATION FEATURES”
    2. Dial 18.
    “ITCM HUNT LINK”
    3. Select first linking station:
    - station 11 - 57: Dial 11 - 57.
    3. Select second linking station:
    station 11 
    - 57: Dial 11 - 57.
    4. Dial * for another link or press SPKR to end.
    VOICE MAIL 
    LINE ID (Optlon)
    The programmer can program the ExecuMail lines with identification (ID) numbers that allow the
    ExecuMail system to identify which line it 
    is answering. The ID numbers that the programmer
    assigns here must match the ID numbers that are selected as part of ExecuMail system
    programming.
    To program this feature, press 
    ITCM t # 7 4 6 * then do the following steps:
    1. Dial 43.
    2. Select line port:“VOICE 
    MAlL LN ID”
    - line port 1-14 = Dial 01 - 14 or Press Al - A14,
    - line port 15,16 = Dial 15,16 or press Bl, 82,
    - line port 17-24 = Dial 17 - 24 (or press HOLD then press Al - A8).
    3. Dial #to clear current ID.
    4. Dial ID number (6 digit maximum).
    5. Press SPKR to end.
    VOICE MAIL TRANSFER ON BUSY (Optlon)
    The programmer can arrange the system to alert a busy telephone that the ExecuMail system is
    attempting to transfer a call to it instead of having it automatically route the call to a voice mail
    box.He or she can use this programming feature to program a station (usually the attendant
    station) for this option.
    To program this feature, press 
    ITCM Q # 7 4 6 t then do the following steps:
    1. Dial 53.“STATION FEATURES!
    2. Dial 31.
    “WAIL XFR ON BSY:
    3. Select station ports to be programmed:
    - station 11 - 57: Dial 11 - 57.
    4. Press SPKR to end. 
    						
    							TAB091
    STATION 10 - PROGRAMMING OVERLAY
    . Cut out along border.
    l Cut out shaded openings.
    l Fit over station faceplate.Al
    A0
    A2A9
    PPO13-100
    A3A10
    A4
    DIGITECHAl 1(REV I OR HIGHER1
    A5 .PROGRAMMING A1 2OVERLAY
    HOLD 
    Bl82 83 
    						
    							COMDlnL
    Made m in the USA
    TECHNICAL ADVISORY BULLETIN
    Date: JUIY 1991ksue: TAB080
    SOFTWARE ENHANCEMENTS FOR
    THE DigiTech DIGITAL TELEPHONE SYSTEM
    This bulletin discusses the following software enhancement and programming clarification for the DigiTech digital
    telephone system:l
    Support for dual 32-button consoles
    l Button mapping with a DigiTech 7700s~xx LCD speakerphone
    Availability of this enhancement is as follows:
    SYSTEMBASE UNIT PRODUCT CODECO408
    GO408 All Revisions
    CO81 6GO81 6 All Revisions
    Cl 632G1632 All RevisionsFEATURE AND BENEFIT
    SOFTWARE CARTRIDGE PRODUCT CODE
    SO408 Rev. 9 and later
    SO81 6 Rev. 9 and later
    S1632 Rev. 9 and later
    The major feature and benefit of the revision 9 software enhancement is per the following discussion.FEATURE
    Dual Console
    FeatureBENEFITThe dual console feature allow users of DiglTech telephone systems to have two 32-button consoles
    (product code 
    DD32X-xx) assigned to one telephone. This feature is especially useful when used
    with a DigiTech Cl632 system that has one or two CM408 expansion modules included with it. The
    dual console feature allows a station user to monitor up to 48 stations from one station location.
    The first 
    32-button console automatically complements the telephone at the port that is logic-paired
    with the port that the console occupies.Install the second 
    32-button console at any station port and,
    using COS programming, assign it as a second console to the same station port that is paired with
    the first console. The dual console should not be placed at station ports 10 or 11.
    DigiTech station ports are logic-paired asfollows:10-1126-2742-43
    12=-1328 - 2944-45
    14-15
    30-3146-47Station ports are as follows:16-1732-3348-49
    Potts 10 through 17 on 4-line, $-station base unit
    18 
    - 1934-35SO-51Potts 70 through 25 on 8-line, 76~station base unit20-2136-37
    52 - 53Ports 70 through 47 on 76-line, 32-station base unit
    22 
    - 2338-3954 - 55Ports 42 through 57 on 16-line, 32-station base unit24-25
    -40 -4156-57with two 4-line, g-station expansion modules
    Continued on next page. . . 
    						
    							DigiTech Software EnhancementTAB080
    FEATUREBENEFITt
    11The first console (the one installed at the logic-paired port) extends the autodial buttons of the paired
    Consoletelephone by 32 and provides DSS/BLF coverage for station ports 10 through 41. Additionally, the
    Featurefirst console provides COS programmlng buttons Cl0 through 
    C41 when needed.Refer to the
    -continuedprogramming overlay that is included at the end of this publication.
    The second console (the one installed at the programmed station port) provides 
    DSS/BLF coverage
    as follows:l
    On a Cl 632 with two CM408 expansion modules, the first 16 buttons are automatically assigned
    (defautted) to station ports 42 through 57.l
    On a Cl 632 with one CM408 expansion module, the first 8 buttons are automatically assigned
    (defaulted) to station ports 42 through 49.l
    On any other smaller station capacity system, all buttons are unassigned.l
    All 32 buttons on the second console are programmable for DSS and/or autodial use.
    The second console provides COS programming buttons C42 through 
    C57 when needed.
    Refer to the programming overlay that is included at the end of this publication.
    It is important to remember that when a second-console assignment is made or cleared, the console
    button mapping and 
    autodial values are reset to match the default values, or any previously
    programmed ones, for the active feature. This means that when the second-console feature is
    cleared, the console installed at that port complements the telephone that is installed at the
    logic-paired port instead of the one at the port set with the second-console programming. The
    console buttons are 
    automaticallv reassigned (defaulted) to stations 10 through 41 or to the maximum
    station number on system. Figure 1 
    illusrates‘a typical dual console configuration.
    A second console can be installed and programmed without
    having a first console installed at a logic-paired port. The
    button assignment is automatically defautted for ac
    second console but can be reprogrammed as
    required. This configuration is convenient
    for adding a console to an existing tele-
    phone installation that already has
    the logic-paired 
    port occupied.
    Do not use this configuration
    for station ports 10 and 12
    because the console buttons
    will not be usable for
    programming.
    Typi&l DigiTech Telephone(-Atgt8tbnPtilo)
    Figure 1. Dual Console WiringContinued on next page. . . 
    						
    							TAB080DiqiTech Software Enhancement
    FEATURE
    Dual
    Console
    Feature
    - continued
    BENEFITSTATION 10 PROGRAMMING
    To program a station port for the second-console feature,
    1.Press ITCM and dial * # 7 4 6 ++ COW/G. MODE
    2.Dial 53 for station features.STATION FEATURES
    3. Dial 34 for second console.SECOND CONSOLE
    4. Assign console to station.
    - Type console port number then type station port number that console is to be assigned to.5. Press SPKR (MNTR) to end.
    To clear a second-console feature assignment,
    1. Repeat steps 1 through 3 above.
    2. Type console port number twice.
    3. Press SPKR (MNTR) to end.
    VDT PROGRAMMING
    To program a station port for the second-console feature,
    1. Type I 
    +# 7 4 6 ++ and press RETURN
    2. Type 3, RETURN for Station COS.
    3. Type 10, RETURN for Miscellaneous Feature Programming.
    4. Type 20, RETURN for Assign Second DSS Console to a Station.
    5. Type 1, RETURN to assign second DSS console to a station.
    6. Type console 
    port number.
    7. Type station port number of assigned station.
    To 
    clear a second-console feature,
    1. Repeat steps 1 through 5 above.
    2. Type 0, RETURN to clear previous assignment.
    3. Type console port number.
    PROGRAMMING CLARIFICATION
    The programming clarification is per the following discussion.
    CLARIFICATION
    DESCRIPTION
    Button MappingWhen programming the button mapping on a DigiTech telephone using a DigiTech 77OOS-xx LCD
    With DiglTechspeakerphone as the programming station, press buttons Al - Al4 and Bl - 83 to select those same
    7700~xx LCDbuttons on the telephone being mapped. Because the DigiTech 77OOS-xx LCD speakerphone does
    Speakerphonesnot provide buttons B4 through B8, dial 103 - 107 to select buttons B4 - 88 on the telephone being
    mapped.
    3 
    						
    							DigiTech Software EnhancementTAB080
    STATION 10 
    - PROGRAMMING OVERLAY
    l Cut out along border.
    ‘it over station faceplate.
    PPO16-000
    PROGRAMMING 
    OVERLAY, DD32X
    ---
    t
    ---
    f C57
    \
    I
    /--- ---’ C25
    t
    Ml :
    ---__-__--
    ;; C25 C41 ,
    II C24 C40 t
    III
    f C23 C39 /
    I1
    i C22 C38 j
    : C24 1 C40 1
    ; C23 C39 
    ’
    ---I-; C22 C38 1
    II; c21 c37 1II C21 1 C37 iI c53 1
    G--t-T
    I
    i C20 C36 II/ C20 1 C36 ;
    I1 Cl9 c35 ;
    ICl9c35 ;.i c51 1 i
    ‘/: Cl8Ic34 tjI c50 j
    p17 /c33 ;j Cl7c33f; c49I
    --t-f; c40I1 Cl6 1 C32 Ii Cl6 1 C32 I
    -cl5 1 c31 IIc15 IC31’ iIC471 I
    I Cl4 c30 ]I; Cl4c30 !
    i1 Cl3 c29 ;I
    I
    I1 Cl2 C28 1
    I
    /Cl1 C27)
    I
    I1 
    Cl0 C26tI---mm--,
    PAMD-PORT
    CONSOLE
    I
    I; Cl3 c29 1
    ; Cl2C28 i
    / Cl1 lC27 1
    I
    I1 Cl0 C26 
    IL-e- -at ’\__- v-d+ i
    PROGRAMMEDDUAL 
    CONSOLE
    PAIRED-PORT
    CONSOLE (SPARE)
    32-BUTTON DSS/BLFCONSOLE
    DD32X-xx 
    						
    All Comdial manuals Comments (0)

    Related Manuals for Comdial DIGITECH Digital Telephone System Instructions Manual