Comdial DIGITECH Digital Telephone System Instructions Manual

							IPress ITCM +# # 7 4 6 +# for base level.I
:EATURE DESCRIPTION
iystem Alarm Report Station: When
18 system has been arranged to report
darms, use this programming feature to
nable stations to display the alarm
eports when the station user takes
lpproprtate action.
JOTE: Also enable system alarm
reporting.See page 
4- 10.
ill-Call and Zone Paglng: Stations can
eceive voice announcements through
he telephone speaker, or through an
external paging speaker connected to a
aA port, and transmit voice
utnouncements with the telephone
landset. Announcements can be made
o certain areas of the system or to all
;tations in the system.
VOTE: A button can be assigned to a
station for paging access per the
procedure shown on page 4-45.ENTRY 
CODE AND PROMPTING DISPLAY
1. Dial 53.“STATION FEATURES”
2. Dial 28.“ALARM RECEIVE 
M
3. Select station ports for programming:
- Station 10 - 57: Dial 10 - 57.
4. Dial 
+ for next station feature.
-OR-
Dial * % for configuration mode.
1. Dial 55.“PAGING”
2. Choose paging assignment.
- Dial 1 for zone 1 originate. “ORIGINATE ZONE 1”
- Dial 2 for zone 2 originate. “ORIGINATE ZONE 2”
- Dial 3 for zone 3 originate “ORIGINATE ZONE 3”
- Dial 4 for all-call originate.“ALL-CALL OR/G.”
- Dial 5 for zone 1 receive“RECEIVE ZONE 1”
- Dial 6 for zone 2 receive“RECEIVE ZONE 2”
- Dial 7 for zone 3 receive“RECEIVE ZONE 3”
- Dial 8 for all-call receive.“ALL-CALL RECNVE”
- Dial 9 to clear all assignments. “CLEAR PAGING”
3. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57
4. Dial 
% to assign other paging.
-OR-
Dial # %+ for configuration mode.REFERENCE RECORD
122844
132945
143046
15II31II47I16321ARI
25II 41II 57I
DEFAULT q NOT ASSIGNEDI
193551
203652
21
3753
102642
117743
28441 
PressSPKRtoi1 
						

							k&s ITCM % # 7 4 6 +k for base level.FEATURE DESCRIPTION
Jrlme Llne (also prlme group or prime
ntercom): A preprogrammed group of
ines, an intercom line, or one individual
ine can be designated to a particular
;tation where it is automatically selected
or use when that station is taken
>ff-hook.
Flexlble Rlnglng Asslgnments: Ringiryassignments are programmed on a per
station/per line basis. Ringing is
controlled for every line that has
appearance at a station. Immediate, or
direct, ringing can be assigned to some
lines and delayed ringing to others.
NOTE: Do not program direct ringing
for lines that are assigned to
direct department calling.
See page 
4- 18.ENTRY CODE AND PROMPTING DISPLAY
REFERENCE RECORD
3a. Assign prime line.“PRIME LINE XX ”
-Lineporti-14=DialOl -14orpressAl -A14
-Lineport15,16=Dial15,16orpressBl,B2.
-Lineport17-24=Dial17-24
-OR-
Press 
HOLD then press Al - A6
lb. Assign prime group,
- Dial 51-54 for gps. l-4.“PRIME L/NE GRP X
k. Assign prime intercom,
- Dial 56 for intercom line.“PRIME INTERCOM
1. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
i. Dial t for next prime line, group, or
intercom assignment.
-OR-
Press 
* t for next station feature.
-OR-
Press 
If +k If for next station feature I. Dial 53.
“STATION FEATURES”MARK STATION/LINE RECORD 0N PAGE 4 40m
!. Dial 15.“PRIME LINE”DEFAULT = NONE ASSIGNED
3lrect Rlnglng
I. Dial 54.
!. Dial 1.
“STAILINE CONFIG.”“DIRECT RING 
”
3. Select line ports for direct ringing:
- Line port 1-14 = Dial 01 - 14 or press Al - Al4
- Line port 15, 16 = Dial 15,16 or press Bl , 82.
- Line port 17 - 24 = Dial 17 - 24
-OR-
Press 
HOLD then press Al - A6
1. Dial f when all line ports are selected.
5. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
3. Dial * when all station ports are selected.
-OR-
Dial 
t t for next station/line ringing assignment
-OR-
Dial 
t +# t for configuration mode.MARK STATION/LINE RECORD ON PAGE 4
B40
DEFAULT 
= ALL LINES DIRECT RING AT
STATION PORTS 10 AND 17
Continued on next pagePress SPKR to end. 
						

							Press ITCM +k # 7 4 6 % for base level.
EATURE DESCRIPTION
lexlble Ringing Asslgnments -
Dntinued
light Transfer (of rlnglng): The
attendant can place the system into the
light transfer (of ringing) mode of
lperation. While in this mode of
operation, special line/station ringing
assignments are active. These
assignments are programmed per this
brocedure.
VOTE: Also refer to night transfer
(of ringing) on page 4-75.
TiNTRY CODE AND PROMPTING DISPLAYEFERENCE RECORD
STA/LINE CONFIG.”
?. Dial 2.“DELAY RING ”
3. Select line ports for delayed ringing:
- Line port 1-14 = Dial 01 - 14 or press Al - Al4
- Line port 15,16 = Dial 1516 or press Bl, B2.
-Lineport17-24=Dial17-24
-OR-
Press HOLD then press Al - A6
1. Dial # when all line ports are selected.
i. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
;. Dial +k when all station ports are selected.
-OR-
Dial +# + for next station/line ringing feature.
-OR-
Dial 9 +k +k for configuration mode.
I. Dial 64.
2. Dial 3.
3. Select line ports:
“STAILINE CONFIG” -MARK STATION/LINE-RECORD ON PAGE 4 40m
“N/G/-/T RING”
DEFAULT = ALL LINES NIGHT RING AT
STATION PORTS 10 AND 17
- Line poti 1-14 = Dial 01 - 14 or press Al - Al4
- Line port 15, 16 = Dial 15,16 or press 81, 82.
- Line port 17 - 24 = Dial 17 - 24
-OR-
Press HOLD then press Al - A8
4. Dial #when all line ports are selected.
5. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
6. Dial 
% when all station ports are selected.
-OR-
Dial + +k for next station/line feature.
-OR-
Dial t 4~ t for-configuration mode.
Press SPKR to err 
						

							Press ITCM +k # 7 4 6 +k for base level.
:EATURE DESCRIPTION
Wvacy Release: A line can be made
Ion-private at a particular station while
emaining private at all other stations.
itations can be programmed to
automatically release privacy while on
certain lines. With this arrangement,
Ither stations can join that particular
station whenever it is on the privacy
elease line.
kcess Denied: Access to particular
ines can be denied to certain stations. A
;tation user cannot select a denied line.
I
ENTRY CODE AND PROMPTING DISPLAYREFERENCE RECORD
1.Dial54.
2. Dial 4.‘STAR/NECONFIG.”MARKSTATION/LINERECORDONPAGE4 m 40
“pR/l//JC)‘/?ELEASE” DEFAULT = ALL LINES PRIVATE
3. Select line ports:
-Lineportl-14=DialOl -140rpressAl -A14
- Line port 15, 16 = Dial 15, 16 or press 81, 82.
-Lineport17-24=Dial17-24
-OR-Press HOLD then press Al 
- A6
4. Dial 
# when all line ports are selected.
5. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
6. Dial 
+k when all station ports are selected.
-OR-Dial 
+k +k for next station/line feature.
-OR-Dial 
% ++ +k for configuration mode.
3. Select line ports:
- Line port 1-14 = Dial 01 - 14 or press Al - Al4
- Line port 15, 16 = Dial 15,16 or press 81, 82.
- Line port 17 - 24 = Dial 17 - 24
-OR-Press HOLD then press Al 
- A6
4. Dial # when all line ports are selected.
5. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
6. Dial 
+k when all station ports are selected.
-OR-Dial 
+# +k for next station/line feature.
-OR-Dial 
% % +k for configuration mode. 1. Dial 64.
“STMINE CONFIG.”2. Dial 5.
“ACCESS DENY”
-I
IPress SPKR to end. 
						

							f
E
Press ITCM +k # 7 4 6 ++ for base level.
‘EATURE DESCRIPTION
Zall Orlglnatlon Denled: The ability to
rrfginate calls on certain lines can be
denied to individual stations. The ability
o answer incoming calls on these lines
s still allowed.
Idle Llne Preference: With idle line
sreference enabled, taking a station
)ff-hook will automatically connect it to
any assigned and idle line programmed
‘or this purpose.
ENTRY CODE AND PROMPTING DISPLAY
I
REFERENCE RECORD
1. Dial 54.
2. Dial 6.
3. Select line ports:
“STMINE CONFIG.”MARK STATION/LINE RECORD ON PAGE 4-40
“ORIGINATION DENY”DEFAULT = NO ORIG. RESTRICTIONS
- Line port l-14 = Dial 01 - 14 or press Al - Al4
- Line port 15, 16 = Dial 15, 16 or press 81, B2.
- Line port 17 - 24 = Dial 17 - 24
-OR-
Press HOLD then press Al - A8
4. Dial # when all line ports are selected.
5. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
6. Dial t when all station ports are selected.
-OR-
Dial ?# + for next station/line feature.
-OR-
Dial % 5 % for configuration mode.
1. Dial 64.
2. Dial 7.
“STALINE CONFIG.”MARK STATION/LINE RECORD ON PAGE 4-40
“/DL E L/NE pR/=F. ”DEFAULT = NONE ASSIGNED
3. Select line ports:
- Line port l-14 = Dial 01 - 14 or press Al - Al4
- Line port 15,16 = Dial 15,16 or press Bl, 82.
-Lineportl7-24=Dial17-24
-OR-
Press HOLD then press Al - A8
4. Dial # when all line ports are selected.
5. Select station ports to be programmed:
- Station 10 - 57: Dial 10 - 57.
6. Dial +% when all station ports are selected.
-OR-
Dial % % for next station/line feature.
-OR-
Dial +% % % for configuration mode.
1Press SPKR to t?YIJ 
						

							System hogrammingIMI 66-083
STATION/LINE CONFIGURATION RECORD 
						

							Press ITCM ?# # 7 4 6 +k for base level.
‘EATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAY
Jon-Square System: Every
)rogrammable buttons at each digital
;tations can be assigned individually
mapped) to select any line assigned to
hat station or to provide other functions.
rhese buttons can be assigned as direct
;tation select (DSS) buttons to provide
tuick access to system stations or
Issigned as idle to provide autodial
juttons for station the user. Idle buttons
31,B2, andB3orA14,A15andAl6
ierve as dynamic line buttons. These
juttons allow the system to temporarily
assign a line appearance to a station
which normally does not have that line
assigned to it. That line will appear at a
jynarnic line button. While the line is in
appearance there, any normal call
landling operations can be performed.
defer to Flgure 4-l on page 4-50 for
Uton locations.
Default Button Asslgnments
hsslgn Llnes To Buttons
Assign Lines To Buttons - Continued
- .on next page
1. Dial 56.“BUTTON MAPPING ”
2. Dial 01.“BUTTON DEFAULT ”
3. Select station ports to be defaulted:
- Station 10 - 57: Dial 10 - 57.
3. Dial * for next button mapping feature.
-OR-
Dial 
t f for configuration mode.
1. Dial 56.
“BUTTON MAPPING ’
2. Dial 02.“ASSIGN LINE n
3. Select button to be programmed:
- Press Al - A14, Bl - B8.
4. Select line ports to be assigned.
- Line port 1-14 = Dial 01 - 14 or Press Al - A14.
-Lineport15,16=Dial15,16orPressBl,B2
- Line port 17 - 24 = Dial 17 - 24.. 
-OR-
Press 
HOLD then press Al - A8.
5. Repeat steps 3 and 4 until all ‘.s: are assigned.
REFERENCE RECORD
SEE CHART ON PAGE 
4- 49I
IPress SPKR to end.I 
						

							l-
PrY ITCM % # 7 4 6 ++ for base level.
:EATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAYREFERENCE RECORD
.lnes To Buttons - continued6. Dial # to finish button mapping.1 SEE CHART ON PAGE 4-49I
7. Select station port to be programmed:
- Station 10 - 57: Dial 10 - 57.
8. Dial 5 for further line/button assignment.
-OR-
Dial 
% t for next button mapping feature.
-OR-
Dial 
++r # # for configuration mode.
\sslgn DWBLF Selectlon To Buttons1. Dial 56.“BUTTON MA PPlNG ”
2. Dial 03.w ASSIGN DSSIBLF ’
3. Select button to be programmed:
- Press Al - A14, Bl - 86.
4. Select station port to be assigned:
- Station 10 - 57: Dial 10 - 57.
5. Repeat steps 3 and 4 until all ports are assigned.
6. Dial #.
7. Select station ports to be programmed
with this 
DSSbutton assignment:
- Station 10 - 57: Dial 10 - 57.
8. Dial * for further DSS/button assignment.
-OR-
Dial 
* * for next button mapping feature. 
-OR-
Dial 
t +r t for configuration mode..
Blank Buttons For User Autodlal and1. Dial 56.“BUTTON MAPPING ”
Dynamic Line Buttons2. Dial 04.%!ANWAUTODIAL ”NOTE When blanking buttons, be
3. Select all buttons to be programmed:sure a previous/y assigned
- Press Al - A14, Bl - 88.button is 
idle (feature not4. Dial #.selected by user) before it is
5. Select station ports to be programmed withblanked
this auto dial button assignment.:
;.c* -
OR-
- Station 10 - 57: Dial 10 - 57.
6. Dial + for further button blanking.
Dial 
t t for next button mapping feature.
-OR-
Dial 
t t t for configuration mode. 
						

							Press ITCM * # 7 4 6 +k for base level.I
FEATURE DESCRIPTION
Wultlple Intercom Button: Stations can
)e programmed to provide a second
ntercom button.
Wvacy Button: Stations can be
lrogrammed to provide a privacy button.
4 user engaged in a 
private call can
lress the privacy button to change the
:urrent call into a non-private one.
I
ENTRY CODE AND PROMPTING DISPLAY
1. Dial 55.“BUTTON MAPPING ’
2. Dial 05.“ASSIGN 2ND ITCM ’
3. Select button to be programmed:
- Press Al - A14,Bl - 86.
4. Select station ports to be programmed
with multiple intercom button:
- Station 10 - 57: Dial 10 - 57.
5. Dial +k for further intercom button assignment
-OR-
Dial t f for next button mapping feature.
-OR-
Dial +k +N +N for configuration mode.
1. Dial 55.
“BU77ON MAPPING ’
2. Dial 05.“ASSIGN PRWACY ”
3. Select button to be programmed:
- Press Al - A14, Bl - B6.
4. Select station ports to be programmed
with a PRIVACY button:
- Station 10 - 57: Dial 10 - 57.
5. Dial % for further privacy button assignment.
-OR-
Dial +k +N for next button mapping feature.
-OR-
Dial +k +# % for configuration mode.
REFERENCE RECORD/
 SEE CHART ON PAGE 4-49I
IPress SPKR to end.I