2012 Na Yamaha Super Tenere Manual

							
haha TIGHTENING TORQUES
2-20
TIP
Cylinder head bolt
Tighten the cylinder head bolts “1”–“8” in the proper tightening sequence as follows:
 Tighten the cylinder head bolts “1”–“6” to 20 Nm (2.0 m·kgf, 14 ft·lbf).
 Tighten the cylinder head bolts “1”–“6” to 30 Nm (3.0 m·\
kgf, 22 ft·lbf), and then tighten them further to  reach the specified angle. Tighten each bolt to the specified angle before tightening the next bolt to 
30 Nm (3.0 m·kgf, 22 ft·lbf).
“1”, “2”, “4”: 215–225°
“3”, “5”, “6”: 180–190°
 Tighten the cylinder head bolts “7” and “8” to 10 Nm (1.0 m·kgf, 7.2 ft·lbf).Oil level switch bolt M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil pipe bolt M6 3 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil pump assembly bolt  M6 3 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Oil pump housing cover bolt M6 6 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil strainer (oil pump) bolt M6 3 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Main axle assembly bolt M6 3 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Shift drum retainer screw M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Shift shaft spring stopper bolt M8 1 22 Nm (2.2 m·kgf, 16 ft·lbf)
Connecting rod nut M9 4
See TIP.
Middle gear side cover screw M6 6 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Middle gear side cover damper 
plate screw M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Engine oil drain bolt (middle 
gear) M8 1 20 Nm (2.0 m·kgf, 14 ft·lbf)
Middle driven pinion gear bearing 
housing bolt M8 4 33 Nm (3.3 m·kgf, 24 ft·lbf)
Middle drive pinion gear bearing 
retainer bolt M8 4 28 Nm (2.8 m·kgf, 20 ft·lbf)
Middle drive pinion gear nut M44 1 110 Nm (11 m·kgf, 80 ft·lbf) Stake.
Starter motor assembly bolt M6 2 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Starter motor terminal nut M6 1 5 Nm (0.5 m·kgf, 3.6 ft·lbf)
Starter motor front cover bolt M5 2 5 Nm (0.5 m·kgf, 3.6 ft·lbf)
Starter motor terminal and rear 
cover nut M6 1 11 Nm (1.1 m·kgf, 8.0 ft·lbf)
Item
Thread 
size Q’ty Tightening torque Remarks
LT
LT
LT
LT
M
LT
LT
LT
LT  
						

							
haha TIGHTENING TORQUES
2-21
TIP
Crankcase bolt
Tighten the crankcase bolts “1 ”–“6” to 10 Nm (1.0 m ·kgf, 7.2 ft· lbf) in the proper tightening sequence.
Then, retighten the bolts one at a time as follows:
 Tighten the crankcase bolts “1 ”–“6” to 20 Nm (2.0 m ·kgf, 14 ft ·lbf).
 Tighten the crankcase bolts “1 ”–“6” further to reach the specified angle 90 –100 °.
 Tighten the crankcase bolts “7 ”–“32”.
 “7 ”–“21” , “30”–“32” : 24 Nm (2.4 m ·kgf, 17 ft ·lbf)
 “ 22”–“29” : 10 Nm (1.0 m ·kgf, 7.2 ft ·lbf)
TIP
Connecting rod nut
Tighten the connecting rod bolts to 20 Nm (2.0 m ·kgf, 14 ft ·lbf), and then tighten them further to reach 
the specified angle 145 –155°.
4
6
1
2
5
3
7
8
9
3
2
10
4 6
11
12
7
8
1
13
15
16
17  18
19
20
21
22
2425
26
27
28
29
14
5
23
A3130
32
B
A. Lower crankcase
B. Upper crankcase  
						

							
haha TIGHTENING TORQUES
2-22
EAS20350
CHASSIS TIGHTENING TORQUES Item Thread 
size Q’
ty Tightening torque Remarks
Engine mounting bolt (front right 
side) M12 2 75 Nm (7.5 m
·kgf, 54 ft ·lbf)
Engine mounting bolt (front left 
side) M12 2 75 Nm (7.5 m
·kgf, 54 ft ·lbf)
Engine mounting bolt (rear right 
lower side) M10 1 68 Nm (6.8 m
·kgf, 49 ft ·lbf)
Engine mounting bolt (rear left 
lower side) M10 1 68 Nm (6.8 m
·kgf, 49 ft ·lbf)
Engine mounting nut  M10 1 68 Nm (6.8 m ·kgf, 49 ft ·lbf)
Engine bracket bolt M12 4 75 Nm (7.5 m ·kgf, 54 ft ·lbf)
Engine positioning bolt  M12 1 23 Nm (2.3 m ·kgf, 17 ft ·lbf)
Rear frame bolt M10 4 59 Nm (5.9 m ·kgf, 43 ft ·lbf)
Centerstand nut M10 2 73 Nm (7.3 m·kgf, 53 ft ·lbf)
Sidestand nut M10 1 69 Nm (6.9 m·kgf, 50 ft ·lbf)
Sidestand bracket bolt M10 2 63 Nm (6.3 m·kgf, 46 ft ·lbf)
Sidestand switch screw M5 2 4.0 Nm (0.40 m·kgf, 2.9 ft ·lbf)
Passenger footrest bolt M8 4 28 Nm (2.8 m·kgf, 20 ft ·lbf)
Left passenger footrest plate bolt M5 2 4.5 Nm (0.45 m ·kgf, 3.3 ft ·lbf)
Muffler protector bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Brake pedal bolt M8 1 26 Nm (2.6 m·kgf, 19 ft ·lbf)
Shift pedal bolt M8 2 30 Nm (3.0 m·kgf, 22 ft ·lbf)
Shift arm bolt M6 1 10 Nm (1.0 m·kgf, 7.2 ft ·lbf)
Shift rod locknut (shift arm side) M6 1 8 Nm (0.8 m ·kgf, 5.8 ft ·lbf)
Shift rod locknut (shift pedal side) M6 1 8 Nm (0.8 m· kgf, 5.8 ft·lbf) Left-hand 
thread
Radiator bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Radiator bracket bolt M8 2 19 Nm (1.9 m·kgf, 14 ft ·lbf)
Radiator cover bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Coolant reservoir bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Fuel tank bolt (front side) M6 2 10 Nm (1.0 m·kgf, 7.2 ft ·lbf)
Fuel tank bolt (rear side) M8 1 16 Nm (1.6 m·kgf, 12 ft ·lbf)
Front fuel tank bracket bolt M6 4 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Rear fuel tank bracket bolt M6 4 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Fuel pump bolt M5 6 4.0 Nm (0.40 m·kgf, 2.9 ft ·lbf)
Fuel tank cap bolt M5 3 6 Nm (0.6 m·kgf, 4.3 ft ·lbf)
Filler neck bolt M6 1 6 Nm (0.6 m·kgf, 4.3 ft ·lbf)
Canister bracket bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Canister bolt M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Throttle cable locknut M6 2 4.5 Nm (0.45 m·kgf, 3.3 ft ·lbf)
LT
LT  
						

							
haha TIGHTENING TORQUES
2-23
Engine guard bolt M6 2 4.5 Nm (0.45 m·kgf, 3.3 ft ·lbf)
Engine guard nut M6 2 4.5 Nm (0.45 m·kgf, 3.3 ft ·lbf)
Engine guard bracket bolt M6 2 10 Nm (1.0 m·kgf, 7.2 ft ·lbf)
Right side panel bolt M5 4 1.5 Nm (0.15 m·kgf, 1.1 ft ·lbf)
Right side inner panel bolt M6 1 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Left side cowling bolt M5 5 1.5 Nm (0.15 m·kgf, 1.1 ft ·lbf)
Left side panel bolt M6 3 4.5 Nm (0.45 m·kgf, 3.3 ft ·lbf)
Passenger seat bolt M8 2 16 Nm (1.6 m·kgf, 12 ft ·lbf)
Standard carrier bolt (110 mm) M8 2 20 Nm (2.0 m ·kgf, 14 ft ·lbf)
Standard carrier bolt (45 mm) M8 1 20 Nm (2.0 m ·kgf, 14 ft ·lbf)
Standard carrier bracket bolt M8 2 20 Nm (2.0 m· kgf, 14 ft·lbf)
Additional carrier bolt M6 4 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Grab bar bolt M10 4 32 Nm (3.2 m·kgf, 23 ft ·lbf)
Seat bracket bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Seat lock latch nut M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Seat lock bolt M6 2 3.0 Nm (0.30 m·kgf, 2.2 ft ·lbf)
Rear fender bolt M6 7 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Rear mudguard bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Hydraulic unit assembly bolt M6 3 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Hydraulic unit brake pipe joint 
bolt M6 2 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Hydraulic unit brake pipe flare nut M10 8 16 Nm (1.6 m ·kgf, 12 ft ·lbf)
Tail/brake light assembly bolt M6 2 15 Nm (1.5 m ·kgf, 11 ft ·lbf)
Tail/brake light assembly bolt M6 2 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Tail/brake light unit screw M6 1 0.4 Nm (0.04 m·kgf, 0.29 ft ·lbf)
Tail/brake light unit screw M5 2 1.5 Nm (0.15 m·kgf, 1.1 ft ·lbf)
License plate light bolt M5 2 3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)
Rear reflector nut M5 1 1.5 Nm (0.15 m·kgf, 1.1 ft ·lbf)
Side reflector nut M5 2 1.8 Nm (0.18 m·kgf, 1.3 ft ·lbf)
Side reflector/license plate brack-
et bolt M6 2 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Lean angle sensor screw M4 2 1.0 Nm (0.10 m·kgf, 0.72 ft ·lbf)
Frame ground lead bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Windshield screw M5 4 0.5 Nm (0.05 m·kgf, 0.36 ft ·lbf)
Meter assembly screw M5 3 1.3 Nm (0.13 m·kgf, 0.94 ft ·lbf)
Headlight assembly bolt M6 4 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Headlight bracket nut M8 1 30 Nm (3.0 m·kgf, 22 ft ·lbf)
Headlight cover bolt M6 4 0.7 Nm (0.07 m·kgf, 0.51 ft ·lbf)
Auxiliary DC jack nut M27 1 2.8 Nm (0.28 m·kgf, 2.0 ft ·lbf)
Item
Thread 
size Q’
ty Tightening torque Remarks  
						

							
haha TIGHTENING TORQUES
2-24
Rearview mirror M10 2 17 Nm (1.7 m·kgf, 12 ft ·lbf)
Grip end bolt  M8 2 27 Nm (2.7 m·kgf, 20 ft ·lbf)
Upper hand shield bolt M5 4 3.8 Nm (0.38 m·kgf, 2.8 ft ·lbf)
Lower hand shield bolt M5 2 4.5 Nm (0.45 m·kgf, 3.3 ft ·lbf)
Hand shield bracket nut M6 2 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
Front brake master cylinder hold-
er bolt M6 2 10 Nm (1.0 m
·kgf, 7.2 ft ·lbf)
Brake master cylinder reservoir 
cap bolt M4 2 1.5 Nm (0.15 m
·kgf, 1.1 ft ·lbf)
Brake lever pivot bolt M6 1 1.0 Nm (0.10 m·kgf, 0.72 ft·lbf)
Brake lever pivot nut M6 1 6 Nm (0.6 m·kgf, 4.3 ft ·lbf)
Clutch master cylinder holder bolt M6 2 14 Nm (1.4 m ·kgf, 10 ft ·lbf)
Clutch master cylinder reservoir 
cap screw M4 2 1.5 Nm (0.15 m
·kgf, 1.1 ft ·lbf)
Clutch lever pivot bolt M6 1 1.0 Nm (0.10 m·kgf, 0.72 ft ·lbf)
Clutch lever pivot nut M6 1 6 Nm (0.6 m·kgf, 4.3 ft ·lbf)
Clutch hose union bolt M10 2 30 Nm (3.0 m·kgf, 22 ft ·lbf)
Clutch hose holder bolt M6 1 9 Nm (0.9 m·kgf, 6.5 ft ·lbf)
Throttle cable housing bolt M5 2 3.8 Nm (0.38 m ·kgf, 2.8 ft ·lbf)
Right handlebar switch screw M5 2 3.5 Nm (0.35 m ·kgf, 2.5 ft ·lbf)
Left handlebar switch screw M5 2 3.5 Nm (0.35 m ·kgf, 2.5 ft ·lbf)
Front brake light switch screw M4 1 1.2 Nm (0.12 m ·kgf, 0.87 ft ·lbf)
Clutch switch screw M4 1 1.2 Nm (0.12 m·kgf, 0.87 ft ·lbf)
Upper handlebar holder bolt M8 4 28 Nm (2.8 m ·kgf, 20 ft ·lbf)
Steering stem nut M24 1 130 Nm (13 m·kgf, 94 ft·lbf)
Lower ring nut M28 1See TIP.
Horn bolt M6 2 14 Nm (1.4 m·kgf, 10 ft ·lbf)
Front brake hose holder and horn 
nut M6 1 9 Nm (0.9 m
·kgf, 6.5 ft ·lbf)
Front fender bolt (front side) M6 4 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Front fender bolt (rear side) M6 2 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Front reflector nut M5 2 1.5 Nm (0.15 m·kgf, 1.1 ft ·lbf)
Upper bracket pinch bolt M8 2 26 Nm (2.6 m·kgf, 19 ft ·lbf)
Lower bracket pinch bolt M8 4 20 Nm (2.0 m·kgf, 14 ft ·lbf)
Front fork cap bolt M46 2 23 Nm (2.3 m·kgf, 17 ft ·lbf)
Damper rod assembly bolt M10 2 23 Nm (2.3 m ·kgf, 17 ft ·lbf)
Damper rod assembly locknut M10 2 15 Nm (1.5 m ·kgf, 11 ft ·lbf)
Front wheel axle bolt M8 1 72 Nm (7.2 m·kgf, 52 ft ·lbf)
Front wheel axle pinch bolt M8 2 See TIP.
Item
Thread 
size Q’
ty Tightening torque Remarks
LT
LT
LT  
						

							
haha TIGHTENING TORQUES
2-25
Front wheel sensor bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Front wheel sensor rotor bolt M6 5 8 Nm (0.8 m· kgf, 5.8 ft·lbf)
Front brake disc bolt M6 10 18 Nm (1.8 m·kgf, 13 ft ·lbf)
Rear wheel axle nut M18 1 125 Nm (12.5 m·kgf, 90 ft ·lbf)
Rear wheel axle pinch bolt M10 1 25 Nm (2.5 m ·kgf, 18 ft ·lbf)
Rear wheel sensor bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Rear wheel sensor rotor bolt M6 5 8 Nm (0.8 m· kgf, 5.8 ft·lbf)
Rear brake disc bolt M8 6 23 Nm (2.3 m·kgf, 17 ft ·lbf)
Spoke BC4 64 6 Nm (0.6 m·kgf, 4.3 ft ·lbf)
Front brake caliper bolt M10 4 40 Nm (4.0 m·kgf, 29 ft ·lbf)
Front brake caliper bleed screw M8 2 5 Nm (0.5 m ·kgf, 3.6 ft ·lbf)
Front brake hose union bolt M10 4 30 Nm (3.0 m ·kgf, 22 ft ·lbf)
Front brake hose union bolt (left 
front brake caliper) M10 1 30 Nm (3.0 m
·kgf, 22 ft ·lbf)
Front brake hose holder and front 
brake hose holder bracket bolt M6 1 9 Nm (0.9 m
·kgf, 6.5 ft ·lbf)
Front brake hose holder bracket 
bolt M6 1 9 Nm (0.9 m
·kgf, 6.5 ft ·lbf)
Front brake hose joint bolt M6 1 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Front brake hose joint bracket 
bolt M6 1 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Front brake hose holder and 
frame bolt M6 1 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Rear brake caliper bolt M10 2 27 Nm (2.7 m·kgf, 20 ft ·lbf)
Rear brake caliper bleed screw M7 1 6 Nm (0.6 m ·kgf, 4.3 ft ·lbf)
Rear brake hose union bolt M10 4 30 Nm (3.0 m· kgf, 22 ft·lbf)
Rear brake hose holder and 
swingarm bolt M6 1 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Rear brake hose holder and 
frame bolt M6 1 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Rear brake hose guide bolt M6 1 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Brake torque rod bolt M8 2 30 Nm (3.0 m·kgf, 22 ft ·lbf)
Rear brake master cylinder bolt M8 2 23 Nm (2.3 m ·kgf, 17 ft ·lbf)
Rear brake master cylinder lock-
nut M10 1 17 Nm (1.7 m
·kgf, 12 ft ·lbf)
Brake fluid reservoir bolt M5 1 3.8 Nm (0.38 m·kgf, 2.8 ft ·lbf)
Brake fluid reservoir cap M42 1 1.5 Nm (0.15 m·kgf, 1.1 ft ·lbf)
Rear shock absorber assembly 
upper nut M10 1 40 Nm (4.0 m
·kgf, 29 ft ·lbf)
Rear shock absorber assembly 
lower nut M12 1 49 Nm (4.9 m
·kgf, 35 ft ·lbf)
Item
Thread 
size Q’
ty Tightening torque Remarks
LT
LT
LT
LT
S  
						

							
haha TIGHTENING TORQUES
2-26
TIP
Lower ring nut
1. First, tighten the lower ring nut to approximately 52 Nm (5.2 m ·kgf, 38 ft ·lbf) with a torque wrench, 
then loosen the lower ring nut completely.
2. Retighten the lower ring nut to 18 Nm (1.8 m ·kgf, 13 ft ·lbf) with a torque wrench.
Relay arm and frame nut M14 1 59 Nm (5.9 m
·kgf, 43 ft ·lbf)
Connecting arm and relay arm 
nut M14 1 59 Nm (5.9 m
·kgf, 43 ft ·lbf)
Connecting arm and swingarm 
nut M14 1 59 Nm (5.9 m
·kgf, 43 ft ·lbf)
Swingarm pivot shaft M22 1 120 Nm (12 m·kgf, 87 ft· lbf)
Swingarm pivot shaft end plate 
bolt M5 2 6 Nm (0.6 m
·kgf, 4.3 ft ·lbf)
Rubber boot cover bolt M6 2 10 Nm (1.0 m·kgf, 7.2 ft ·lbf)
Rubber boot joint bolt M5 3 3.8 Nm (0.38 m·kgf, 2.8 ft ·lbf)
Final drive assembly nut M10 4 42 Nm (4.2 m·kgf, 30 ft·lbf)
Final gear oil drain bolt M14 1 23 Nm (2.3 m·kgf, 17 ft ·lbf)
Final gear oil filler bolt M14 1 23 Nm (2.3 m·kgf, 17 ft ·lbf)
Ring gear bearing housing bolt M10 2 40 Nm (4.0 m ·kgf, 29 ft ·lbf)
Ring gear bearing housing bolt M8 6 23 Nm (2.3 m ·kgf, 17 ft ·lbf)
Coupling gear nut M20 1 150 Nm (15 m·kgf, 108 ft·lbf) Stake.
Bearing retainer M75 1 130 Nm (13 m·kgf, 94 ft·lbf)Left-hand 
thread
Final driven pinion gear bearing 
holder screw M6 1 7 Nm (0.7 m
·kgf, 5.1 ft ·lbf)
Ring gear stopper bolt M10 1 9 Nm (0.9 m·kgf, 6.5 ft ·lbf) Left-hand 
thread
Electrical components tray bolt M6 3 10 Nm (1.0 m ·kgf, 7.2 ft ·lbf)
Electrical components tray bolt M6 1 7 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
Electrical components tray brack-
et bolt M8 2 19 Nm (1.9 m
·kgf, 14 ft ·lbf)
ECU bracket bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Rectifier/regulator bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft ·lbf)
Fuse box bracket screw M5 1 0.8 Nm (0.08 m·kgf, 0.58 ft ·lbf)
Positive battery lead and starter 
relay bolt M6 1 3.6 Nm (0.36 m
·kgf, 2.6 ft ·lbf)
Negative battery lead and starter 
relay bolt M6 1 3.6 Nm (0.36 m
·kgf, 2.6 ft ·lbf)
Item
Thread 
size Q’
ty Tightening torque Remarks
LT
LT
LT
LT  
						

							
haha TIGHTENING TORQUES
2-27
TIP
Front wheel axle pinch bolt
1. Insert the front wheel axle from the right side and tighten it to 72 Nm (7.2 m ·kgf, 52 ft ·lbf).
2. In the order pinch bolt  “1”  pinch bolt  “2”  pinch bolt “1” , tighten each bolt to 21 Nm (2.1 m ·kgf, 
15 ft ·lbf) without performing temporary tightening.
21  
						

							
haha LUBRICATION POINTS AND LUBRICANT TYPES2-28
EAS20360
LUBRICATION POINTS AND LUBRICANT TYPES
EAS20370
ENGINE Lubrication point Lubricant
Oil seal lips
O-rings
Bearings
Camshaft lobes and camshaft journals
Valve stems (intake and exhaust)
Valve stem ends (intake and exhaust)
Valve lifters
Crankshaft big ends
Piston surfaces
Piston pins
Connecting rod bolts
Crankshaft journals
Primary driven gear
Balancer gears
Balancer shaft journals
Decompression camshaft moving point
Oil pump rotors (inner and outer)
Crankcase bolt O-rings (balancer shaft journal)
Rear balancer holder
Torque limiter
Starter clutch idle gear shaft
Starter clutch gear
Primary driven gear (clutch housing)
Thrust washer
Spacers
Long clutch push rod
Short clutch push rod
Ball
Clutch boss nut thread and conical spring washer
Transmission gears (wheel and pinion) and collars
Main axle and drive axle
Torque damper cam inner surface and contact surfaces
Middle drive pinion gear inner surface
LS
LS
E
M
M
M
E
E
E
E
M
E
E
E
E
E
E
E
E
E
E
E
E
E
E
LS
LS
LS
E
M
M
M
M  
						

							
haha LUBRICATION POINTS AND LUBRICANT TYPES2-29
Middle driven pinion gear
Shift forks and shift fork guide bars
Shift drum assembly
Shift shaft washer
Universal joint inner surface
Ring gear thrust washer Yamaha genuine 
shaft drive oil SAE 80  API GL-5 or SAE 80  API GL-4 Hypoid  gear oil
Ring gear splines
Ring gear bearing Yamaha genuine 
shaft drive oil SAE 80  API GL-5 or SAE 80  API GL-4 Hypoid  gear oil
Drive shaft splines
Universal joint bearing
Drive shaft oil seal
Cylinder head cover and gasket Three bond 
No.1541C ®
Cylinder head and gasket Yamaha bond 
No.1215 (Three bond  No.1215 ®)
Crankcase mating surfaces Yamaha bond 
No.1215 (Three bond  No.1215 ®)
Stator assembly lead grommet Yamaha bond 
No.1215 (Three bond  No.1215 ®)
Lubrication point
LubricantE
E
E
E
LS
LS
M
LS
LS