Xerox WorkCentre M20i User Manual

							Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide Page 4-1
4 Paper and Other Media
There is one Paper Tray and a Bypass Tray as standard on the 
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre 
M20i. A second Paper Tray is available to purchase as an 
option.
¾Loading Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
¾Setting the Paper Size . . . . . . . . . . . . . . . . . . . . . . 4-8
¾Media Specifications  . . . . . . . . . . . . . . . . . . . . . . . 4-9
Downloaded From ManualsPrinter.com Manuals 
						

							Page 4-2  Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide 
Paper and Other Media
Loading Paper
Preparing Paper for Loading
Before loading paper into the Paper Trays, fan the edges. This procedure separates any 
sheets of paper that are stuck together and reduces the possibility of paper jams. 
)To avoid unnecessary paper jams and misfeeds do not remove paper from its packaging until 
required.
Using the Paper Trays
Loading the Paper Trays
Using the instructions provided, load paper into the machine. Up to two Paper Trays are 
available, depending on your machine configuration. The Paper Trays can hold a maximum 
of 550 sheets of 80 g/m
2 (20 lb) plain paper.
1¾To load paper, pull open the 
Paper Tray.
2¾Push down on the pressure plate 
until it locks into position.
Downloaded From ManualsPrinter.com Manuals 
						

							Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide Page 4-3
Paper and Other Media
zIf you experience 
problems with 
paper feed, turn 
the paper around 
and if the problem 
continues, use 
the Bypass Tray. 
3¾Adjust the rear paper guide to the 
required paper length.
It is preset to A4 or Letter size 
depending on country.
¾To load another size, lift the rear 
guide out of the current position 
and into the required position.
LThe Paper Trays can hold a 
maximum of 550 sheets of 80 g/m2 
(20 lb) plain paper. You can use 
A4, Letter or Legal size paper only.
Rear 
Guide
4
¾Fan the paper and insert it into 
the tray.
If loading Letterhead, ensure the 
design is face-up and the top 
edge of the sheet is placed at the 
right side.
Downloaded From ManualsPrinter.com Manuals 
						

							Page 4-4  Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide 
Paper and Other Media
zWhen printing 
from your PC, 
ensure you select 
the Paper Source 
and the correct 
paper size from 
your software 
application.
)Use the instructions “Setting the Paper Size” on page 4-8 to set the correct size for the Paper 
Tr a y.
5
Corner 
snubbers
¾Ensure that the paper is 
positioned under the snubbers.
¾Do not fill above the Maximum Fill 
Line.
Max Fill
Line
6
¾Position the side guide by 
squeezing the lever and sliding it 
toward the stack of paper, until it 
gently touches the side of the 
stack.
Do not allow the guide to press 
against the edge of the paper 
tightly.
¾Close the Paper Tray.
Downloaded From ManualsPrinter.com Manuals 
						

							Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide Page 4-5
Paper and Other Media
Using the Bypass Tray
The Bypass Tray is located on the right side of your machine. It can be closed when not in 
use, making the product more compact. Use the Bypass Tray to print transparencies, labels, 
envelopes or postcards in addition to making quick runs of paper types or sizes that are not 
currently loaded in the paper tray.
Acceptable print media is plain paper with sizes ranging from 98 x 148 mm (3.86 x 5.83 inch), 
to Legal size (216 x 356 mm / 8.5 x 14 inch) and weighing between 60 g/m
2 and 160 g/m2 (16 
lb and 43 lb).
The following table summarizes the print media allowed and the maximum stacking height for 
each paper type.
LThe height is measured with the stack of sheets laid on a flat surface.
7¾To select a paper tray, press the 
[Paper Supply] key until the 
required tray is lit on the Status 
Map.
Tr a y  1 and the Bypass Tray are 
available as standard, Tray 2 is 
optional. 
If two tray lights display together, 
the Auto Tray Switching feature is 
active. When one tray runs out of 
paper, the machine will switch to 
the other selected tray.
Enter
Paper SupplyStatus Map
PAPER TYPEMAXIMUM STACKING HEIGHT
Plain/Bond/Colored and Pre-
printed Paper100 sheets or 9 mm (0.35 inch)
Envelope10 envelopes or 9 mm (035 inch)
Transparency30 sheets or 9 mm (0.35 inch)
Label10 sheets or 9 mm (0.35 inch)
Cardstock10 sheets or 9 mm (0.35 inch)
Downloaded From ManualsPrinter.com Manuals 
						

							Page 4-6  Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide 
Paper and Other Media
Loading the Bypass Tray
zRemove any curl 
on postcards, 
envelopes, and 
labels before 
loading them into 
the Bypass Tray.
zHold 
transparencies by 
the edges and 
avoid touching 
the print side.
1
¾Lower the Bypass Tray, located 
on the right side of the product.
¾Unfold the Paper Support 
extension.
Bypass Tray
Paper 
Support
2
¾Prepare a stack of paper or 
envelopes for loading by flexing 
or fanning them back and forth. 
Straighten the edges on a level 
surface.
3¾Load the print material with the 
print side facing down and 
against the right edge of the tray.
34
¾Adjust the paper guide to the 
width of the stack of print 
material.
Ensure you have not loaded too 
much print media. The stack 
should be under the Max. Fill 
Line.
Downloaded From ManualsPrinter.com Manuals 
						

							Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide Page 4-7
Paper and Other Media
)Use the instructions “Setting the Paper Size” on page 4-8 to set the correct size for the Bypass Tr a y.
5¾To  s e l e c t  t h e  Bypass Tray, press 
the [Paper Supply] key until the 
Bypass tray is lit on the Status 
Map.
¾When the Bypass Tray is 
selected the Paper Type option 
displays.   Use the Navigation 
Keys to select the Paper Type 
being loaded and press [Enter].
Paper Supply
Status MapEnter
Downloaded From ManualsPrinter.com Manuals 
						

							Page 4-8  Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide 
Paper and Other Media
Setting the Paper Size
After loading paper in the Paper Trays, you will need to set the default Paper Size. Use the 
following instructions to set the default Paper Size for each tray.
¾Press the [Machine Status] key on the Control Panel.
¾Select [Machine Setup] using the Navigation Keys and press [Enter].
The display shows [Tray 1 Size] on the bottom line.
¾Press [Enter].
¾Use the Navigation Keys to select the Paper Size required and press [Enter] to save the 
selection.
¾Repeat the procedure for [Tray 2 Size] if available, and [Bypass Size].
¾Press [Menu/Exit] to exit each menu level and return to Standby mode.
1
2
13
4
Downloaded From ManualsPrinter.com Manuals 
						

							Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide Page 4-9
Paper and Other Media
Media Specifications
Media Sizes and Types
The table below identifies the media sizes which can be used in the Paper Tray and Bypass 
Tr a y, and the capacities which can be loaded.
La. Depending on paper thickness, maximum capacity may be reduced.b. Feed one sheet at a time through the Bypass Tray if jams occur.
MEDIA SIZEINPUT SOURCE CAPACITYa
Paper TrayBypass Tray
Plain paper
Letter (8.5 x 11 inch) 
Folio (8.5 x 13 inch)
Legal (8.5 x 14 inch)
Executive (7.25 x 10.5 inch)
A4 (210 x 297 mm)
B5 (182 x 257 mm)
A5 (148 x 210 mm)YES
YES
YES
NO
YES
NO
NO550
550
550
0
550
0
0YES
YES
YES
YES
YES
YES
YES100
100
100
100
100
100
100
Envelopes
No. 10 (8.5 x 14 inch)
C5 (6.38 x 9.37 inch)
DL (110 x 220 mm)
Monarch (3.87 x 7.5 inch)
B5 (176 x 250 mm)
NO
NO
NO
NO
NO0
0
0
0
0YES
YES
YES
YES
YES10
10
10
10
10
Labels
b
Letter (8.5 x 11 inch)
A4 (210 x 297 mm)NO
NO0
0YES
YES10
10
Transparency filmsb
Letter (8.5 x 11 inch)
A4 (210 x 297 mm)NO
NO0
0YES
YES30
30
Card stocks
b
A6 (105 x 148.5)
Post Card (4 x 6 inch)
Hagaki (5.83 x 8.27 inch)NO
NO
NO0
0
0YES
YES
YES10
10
10
Downloaded From ManualsPrinter.com Manuals 
						

							Page 4-10  Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide 
Paper and Other Media
Media Guidelines
When selecting or loading paper, envelopes, or other special media please adhere to these 
guidelines:
¾Attempting to print on damp, curled, wrinkled, or torn paper can cause paper jams and 
poor print quality. 
¾Use only high quality copier grade paper. Avoid paper with embossed lettering, 
perforations, or texture that is too smooth or too rough. 
¾Store paper in its ream wrapper until ready to use. Place cartons on pallets or shelves, not 
on the floor. Do not place heavy objects on top of the paper, whether it is packaged or 
unpackaged. Keep it away from moisture, or other conditions that can cause it to wrinkle or 
curl. 
¾During storage, moisture-proof wrap (any plastic container or bag) should be used to 
prevent dust and moisture from contaminating your paper. 
¾Always use paper and other media that conform with the specifications detailed in 
“General Specifications” on page 12-6. 
¾Use only well-constructed envelopes with sharp, well creased folds:
- DO NOT use envelopes with clasps and snaps. 
- DO NOT use envelopes with windows, coated lining, self-adhesive seals, or other 
synthetic materials. 
- DO NOT use damaged or poorly made envelopes. 
¾It is recommended that you feed special paper types one sheet at a time. 
¾Only use the special media recommended for use in laser printers. 
¾To prevent special media such as transparencies and label sheets from sticking together, 
remove them from the exit tray as they are printed. 
¾Place transparencies on a flat surface after removing them from the machine. 
¾Do not leave the film in the paper tray for long periods of time. Dust and dirt may 
accumulate on them resulting in spotty printing. 
¾To avoid smudging caused by fingerprints, handle transparencies and coated paper 
carefully. 
¾To avoid fading, do not expose the printed transparencies to prolonged sunlight. 
¾Store unused media at temperatures between 59oF and 86oF (15oC to 30oC). The relative 
humidity should be between 10% and 70%. 
¾Do not load more than 10 sheets of special media into the Bypass Tray at a time. 
Downloaded From ManualsPrinter.com Manuals