Home > Samsung > Printer > Samsung Xpress C460W Manual

Samsung Xpress C460W Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Samsung Xpress C460W Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Media and tray
    412. Menu Overview and Basic Setup
    5 Place the paper with the side you want to print facing up.
    For paper smaller than Letter-sized,  press and unlatch the guide lock in 
    the tray, push the tray in manually.  Then adjust the paper length guide 
    and paper width guide. For paper longer than Legal-sized, 
    press and unlatch the guide lock in 
    the tray, pull the tray out manually.  Then adjust the paper length guide 
    and paper width guide.
     
    • Do not push the paper width guide too far causing the media to warp.
    • Do not use a paper with a leading-edge curl, it may caus e a paper jam or 
    the paper can be wrinkled.
    • If you do not adjust the paper width guide, it may cause paper jams.
     
    2
    1
    2
    1 
    						
    							Media and tray
    422. Menu Overview and Basic Setup
    6 Squeeze the paper width guide and slide it to the edge of the paper stack 
    without causing it to bend.
    7 Close the paper cover.
    8 Insert the paper tray.
    9 When you print a document, set the pa per type and size for the tray (see 
    "Setting the paper size  and type" on page 46).
    The tray is preset to Letter  or A4 size, depending on yo ur country. To change the 
    size to A4 or Letter, yo u must adjust the lever and  paper width guide properly. 
    						
    							Media and tray
    432. Menu Overview and Basic Setup
    1Pull the tray out of the machine. Open the paper cover and remove 
    paper from the tray if necessary.
    2 If you want to change the  size to Letter, hold the lever at the back of the 
    tray, and rotate th e lever clockwise.
    3 Squeeze the paper width guide and sl ide it to the edge of the lever.
     
    If you want to change the size to A4, first move the paper width guide to left 
    and rotate the lever counterclockwise. If you force the lever, it could 
    damage the tray.
     
    LTRA4
    LT RA4 
    						
    							Media and tray
    442. Menu Overview and Basic Setup
    4 
    Printing on special media
    The table below shows the special media usable in tray. 
    The paper setting in the machine and dri ver should match to print without a 
    paper mismatch error. 
    To change the paper setting  set in the machine, from the Samsung Easy Printer 
    Manager  select (Switch to advanced mode)  > Device Settings .
    Or if your machine supports a display  screen, you can set it using the  (Menu) 
    button on the control panel.
    Then, set the paper type from the  Printing preferences window > Paper tab > 
    Paper Type (see "Opening printing pr eferences" on page 54).
     
    • When using special media, we recommend you feed one sheet at a time 
    (see "Print media specifications" on page 117).
    • Illustrations on this user’s gu ide may differ from your machine 
    depending on its options or mode ls. Check your machine type (see 
    "Front view" on page 20).
     
    To see paper weights for each sheet, refer  to "Print media specifications" on 
    page 117.
    ( ● : Supported, Blank: Not supported) 
    TypesTraya
    a. The paper types available manual feeding in tray.
    Plain ●
    Thick ●
    Thin  ●
    Bond ●
    Color  ●
    CardStock ●
    Labels ●
    Preprinted  ●
    Cotton ●
    Recycled ●
    Archive ●
    Glossy Photo ●
    Matte Photo ● 
    						
    							Media and tray
    452. Menu Overview and Basic Setup
    Labels
    To avoid damaging the machine, use only labels designed for use in laser 
    printers.
    • When selecting labels, cons ider the following factors:
    - Adhesives:  Should be stable at your  machine’s fusing temperature 
    about 170°C (338°F).
    - Arrangement:  Only use labels with no exposed backing between them. 
    Labels can peel off sheets that have spaces between the labels, causing \я
    serious jams.
    - Curl:  Must lie flat with no more than  13 mm of curl in any direction.
    - Condition:  Do not use labels with wr inkles, bubbles, or other 
    indications of separation.
    • Make sure that there is no exposed adhesive material  between labels. 
    Exposed areas can cause labels to peel  off during printing, which can cause 
    paper jams. Exposed adhesive can  also cause damage to machine 
    components. • Do not run a sheet of labels throug
    h the machine more than once. The 
    adhesive backing is designed for on ly a single pass through the machine.
    • Do not use labels that are  separating from the backing sheet or are wrinkled, 
    bubbled, or otherwise damaged.
    Card stock/ Custom-sized paper
    • In the software application, set the margins to at least 6.4 mm (0.25 inches)  away from the edges of the material. 
    						
    							Media and tray
    462. Menu Overview and Basic Setup
    Preprinted paper
    When loading preprinted paper, the printed side should be facing up with an 
    uncurled edge at the front. If you expe rience problems with paper feeding, turn 
    the paper around. Note that pr int quality is not guaranteed.
    • Must be printed with heat-resistant  ink that will not melt, vaporize, or 
    release hazardous emissions when sub jected to the machine’s fusing 
    temperature for 0.1 second (about 170°C (338°F)).
    • Preprinted paper ink m ust be non-flammable and should not adversely 
    affect machine rollers.
    • Before you load preprinted  paper, verify that the ink on the paper is dry. 
    During the fusing process, wet ink can  come off preprinted paper, reducing 
    print quality.
    5 
    Setting the paper size and type
    After loading paper in the paper tray,  set the paper size and type using the 
    control panel buttons. 
     
    • The paper setting in the machine and driver should match to print  without a paper mismatch error. 
    To change the paper setting se t in the machine, from the Samsung Easy 
    Printer Manager  select  (Switch to advanced mode)  > Device 
    Settings .
    Or if your machine supports a display screen, you can set it using the 
    (Menu ) button on the control panel.
    Then, set the paper type from the  Printing preferences window > 
    Paper  tab > Paper Type  (see "Opening printing preferences" on page 
    54).
    • It may be necessary to press  OK to navigate to lower-level menus for 
    some models.
     
    1Select ( Menu) button on the control panel.
    2 Press System Setup  > Paper Setup  > Paper Size  or Paper Type.
    3 Select the tray and the option you want.
    4 Press  OK to save the selection. 
    						
    							Media and tray
    472. Menu Overview and Basic Setup
    5 Press (Stop/Clear ) to return to ready mode.
     
    • If you want to use special-sized pape r such as billing paper, select the 
    Paper  tab > Size > Edit... and set  Custom Paper Size Settings  in the 
    Printing Preferences  (see "Opening printing preferences" on page 54).
     
    6 
    Using the output support
     
    The surface of the output tray may become hot if you print a large number 
    of pages at once. Make sure that you do not touch the surface, and do not 
    allow children near it.
     
    The printed pages stack on  the output support, and the output support will help 
    the printed pages to align. The printer  sends output to the output tray by 
    default.
     
    Illustrations on this user’s guide ma y differ from your machine depending 
    on its options or models. Check your  machine type (see "Front view" on 
    page 20).
      
    						
    							Media and tray
    482. Menu Overview and Basic Setup
    7 
    Preparing originals 
    • Do not load paper smaller than 142 x 148 mm (5.6 x 5.8 inches) or larger than 216 x 356 mm (8.5  x 14 inches).
    • Do not attempt to load the following  s of paper, in order to prevent paper 
    jam, low print quali ty and machine damage.
    - Carbon-paper or carbon-backed paper
    - Coated paper
    - Onion skin or thin paper
    - Wrinkled or creased paper
    - Curled or rolled paper
    - Torn paper
    • Remove all staples and pa per clips before loading.
    • Make sure any glue, ink, or correction  fluid on the paper is completely dry 
    before loading.
    • Do not load originals that include  different sizes or weights of paper.
    • Do not load booklets, pamph lets, transparencies, or documents with other 
    unusual characteristics.
    8 
    Loading originals
    You can use the scanner glass or the docum ent feeder to load an original for 
    copying, scanning, and sending a fax.
     
    Illustrations on this user’s guide ma y differ from your machine depending 
    on its options or models. Check your  machine type (see "Front view" on 
    page 20).
     
    On the scanner glass
    Using the scanner glass, you can copy or  scan originals. You can get the best 
    scan quality, especially for  colored or gray-scaled images.  Make sure that no 
    originals are in the document feeder. If an original is detected in the \яdocument 
    feeder, the machine gives it  priority over the original on the scanner glass. 
    						
    							Media and tray
    492. Menu Overview and Basic Setup
    1Lift and open the scanner lid.2 Place the original face down on the scanner glass. Align it with the 
    registration guide at the t op left corner of the glass.
    3 Close the scanner lid. 
    						
    							Media and tray
    502. Menu Overview and Basic Setup
     
    • Leaving the scanner lid open while copying may affect copy quality and toner consumption.
    • Dust on the scanner glass may cause black spots on the printout. Always  keep it clean (see "Cleaning the machine" on page 89).
    • If you are copying a page from a book  or magazine, lift the scanner lid 
    until its hinges are caught by the stopper and then close the lid. If the 
    book or magazine is thicker than 30 mm, start copying with the scanner 
    lid open.
     
     
    • Be careful not to break the sc anner glass. You may get hurt.
    • Do not put hands while closing the sc anner lid. The scanner lid may fall 
    on your hands and get hurt.
    • Do not look into the light from insi de of the scanner while copying or 
    scanning. It is harmful to eyes.
     
    In the document feeder 
    1Flex or fan the edge of the paper  stack to separate the pages before 
    loading originals.
    2 Load the original face up  into the document feeder input tray. Make sure 
    that the bottom of the  original stack matches th e paper size marked on 
    the document input tray. 
    						
    All Samsung manuals Comments (0)

    Related Manuals for Samsung Xpress C460W Manual