Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							12
3
4
5
6
78
9
10
11
12
4-5
2
Press the  EDIT  key to enter the edit menu, and
press the  DUAL PAGE  key.
5
If you need a binding margin, set the left margin.
 Page 4-2
 Select other copy modes as required.
4
Press the  BASIC  key to enter the basic menu,
then select LT (or A4, B5) copy size. 
 Page 3-2
1
Place paper in the drawer(s).  Page 2-4
- When using this mode in bypass copying, be sure to specify the paper size. 
 Page 5 -10, 5 -11
Utilizing this feature allows the facing pages of a book or magazine to be copied page by page onto two
separate sheets of paper or duplex-copied on one sheet. There is no need to move the original on the
glass. You can also place a pair of LT (or A4, B5) sized originals side by side and copy them on separate
sheets of paper.
* Only LT, A4 or B5 sized sheets of paper can be used in this mode.
3
Press the  1 SIDE  (or  2 SIDE ) key.
- Select the  1 SIDE  key to make copies of the facing pages
on two separate sheets of paper page by page. Select the
2 SIDE  key to make duplex copies of them on one sheet.
-12- -13--12- -13-
3. DUAL-PAGE
(To be continued) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-6USING THE EDITING FUNCTIONS
7
Turn to the next page, set the book again and
press the  
START  key.
- Repeat the above procedure until all your originals have been
scanned.
8
After all your originals have been scanned, press
the  FINISHED  key.
- Press the  COPY FINAL PAGE  key if the last original has
only one page.
6
Place the first page(s) to be copied on the glass,
and press the  
START  key.
- If you do not copy your originals from the first page, the copies
will not be arranged in the same order as the original.
- Center the book on the yellow indicator line with the bottom
toward you.
Indicator line
3. DUAL PAGE (Cont.) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-7
5
Press the lower  SET  key.
4
Set the reproduction ratios for the X (horizontal)
and Y  (vertical)  directions,  respectively.
- Using the  25%<  and  >400%  keys on the screen (Use
100%  key if you want the same size as original.), set the
reproduction ratio for X and press the upper  SET  key.
Similarly, set the reproduction ratio for Y.
When placing the original on the reversing automatic
document feeder, set the reproduction ratios from 25 to
200%.
2
Place the original(s).  Page 2-9
3
Press the  EDIT  key to enter the edit menu, and
press the  XY ZOOM  key.
1
Place paper in the drawer(s).  Page 2-4
You can make copies with different reproduction ratios set for the X (horizontal) and Y (vertical) directions,
respectively.
4. X-Y ZOOM
100%
200%
100%
200%
 Select other copy modes as required.
6
Press the   START  key. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-8USING THE EDITING FUNCTIONS
3
Press the  TRIM  (or  MASK ) key.
2
Press the  EDIT  key to enter the edit menu, and
press the  EDITING  key.
5. IMAGE EDITING
You can select an area on an original and copy it with the area trimmed (only the inside of the area
copied) or masked (only the outside of the area copied). Four rectangular areas can be specified on an
original.
* Image editing is only possible with standard sized originals.
* If the settings of the original and copy sizes are not made appropriately, the image may not be copied
completely.
1
Place paper in the drawer(s).  Page 2-4
- When using this mode in bypass copying, be sure to specify
the paper size. 
 Page 5- 10, 5 -11
Trimming Masking
Trimming/Masking 
						

							12
3
4
5
6
78
9
10
11
12
4-9
6
Enter the distance values read in step 5 for the
specified area.
- Key in the value for X1 with the digital keys and press the upper  SET  key.
- Similarly, set the values for X2, Y1 and Y2.
- When setting X1, X2, Y1 and Y2, the original scale automatically changes to the next original scale. Set the
next original scale as same procedure.
Proceed to step 7, if there is no need to set other
trimming/masking positions.
4
Place an original on the glass to specify the area.
- Set the original face up with the bottom toward you, fit its top
left corner against the top left corner of the glass, and align
it with the original scale.
5
Using the original scale on the left and the inner
(top) scale, read the position of the desired area
as follows:
- X1 Distance from the top left to the left edge of the specified area.
- X2 Distance from the top left to the right edge of the specified area.
- Y1 Distance from the top left to the upper edge of the
specified area.
- Y2 Distance from the top left to the lower edge of the specified area.
Four rectangular areas can be specified on an original.
7
Press the lower  SET  key.
 Select other copy modes as required.
9
Press the  START  key.
8
Place the original. (Sheet original Page 2-10)
- Place the original(s) on the glass with the face down, with its bottom toward you, with its top left aligned against the
original scale on the left side.
*25.4mm = 1” 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-10USING THE EDITING FUNCTIONS
 Select other copy modes as required.
5
Press the  START  key.
3
Press the  EDIT  key to enter the edit menu, and
press the  EDITING  key.
Copies are made with images completely reversed in terms of right and left.
Mirror Image
2
Place the original(s).  Page 2-9
1
Place paper in the drawer(s).  Page 2-4
- When using this mode in bypass copying , be sure to specify
the paper size. 
 Page 5-10, 5-11
5. IMAGE EDITING (Cont.)
4
Press the  MIRROR  key. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-11
 Select other copy modes as required.
5
Press the  START  key.
2
Place the original(s).  Page 2-9
3
Press the  EDIT  key to enter the edit menu, and
press the  EDITING  key.
Negative/Positive Reversal
The white area of originals copying black, and the black area of originals copying white.
1
Place paper in the drawer(s).  Page 2-4
4
Press the  NEG/POS  key. 
						

							12
3
4
5
6
78
9
10
11
12
4-12USING THE EDITING FUNCTIONS
When a copy is turned with the line —·—·— as a pivot, originals are printed on side 2 (back face) as
shown.
6. 2 IN 1 / 4 IN 1
This feature allows multiple originals to be reduced and copied onto a single sheet which size is the same
size as the original. There are two modes: 2 IN 1 copying, where two originals are reduced and copied
onto a single sheet, and 4 IN 1 copying, where four originals are reduced and copied onto a single sheet.
In addition, duplex 2 IN 1 / 4 IN 1 modes are available, where four/eight originals can be copied to two
sides of a single sheet of paper.
* 2 IN 1/4 IN 1 duplex copying mode requires the optional automatic duplexer to be installed.
The combination of page arrangement differs depending on the direction of originals set on the reversing
automatic document feeder.
 2IN1
Copy
Originals
 4IN1
 2IN1 DUPLEXSIDE 1
SIDE 2
 4IN1 DUPLEX
SIDE 1 SIDE 2 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-13
 Select other copy modes as required.
6
Press the  START  key.
- When placing an original on the glass, perform steps 5 and
6 on page 2-3 as needed.
4
Select the type of image combination.
- Press the 2IN1 (or  4IN1 ,  2IN1 ,  DUPLEX  or
4IN1 DUPLEX ) key.
5
Select the type of the original.
- Press the  1 SIDE  (or  2 SIDE ) key.
3
Press the  EDIT  key to enter the edit menu, and
press the  2IN1/4IN1  key.
1
Place paper in the drawer(s).  Page 2-4
- When using this mode in bypass copying, be sure to specify
the paper size. 
 Page 5-10, 5-11
To make copies onto paper which is not the same size as
originals, press the  ZOOM...  key to enter the right menu, and
press the size you desire.
2
Place the original(s).  Page 2-9 
						

							12
3
4
5
6
78
9
10
11
12
4-14USING THE EDITING FUNCTIONS
Copies are made with the current date and time, at which they are made, printed on the copy.
Date and time printed at the
bottom of the portrait copy Date and time printed at the
top of the landscape copy
2
Place the original(s).  Page 2-9
3
Press the  EDIT  key to enter the edit menu, and
press the  ANNOTATION  key.
- If the desired function keys are not displayed, press the
Next  or  Pre  key to change the menu screen.
4
Select the orientation (Short edge or Long edge)
and position (UPPER or LOWER) of the date and
time to be printed. Then, press the  SET  key.
7. COPYING WITH ANNOTATION
1
Place paper in the drawer(s).  Page 2-4
 Select other copy modes as required.
5
Press the  START  key.
11.15. 2002  14:54 11.15. 2002  14:54
There may be situations
when the image or
character(s) overlap an
annotation (such as date
and time, etc.)