Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							1
2
3
4
5
6
7
8
9
10
11
12
5-3
Single-feed Mode
3
Press the  SADF  key.
 Select other copy modes as required.
4
Place an original.  Page 2-9
- The original is automatically pulled in and the screen changes
as shown on the right.
- If there are more originals, set them in the same way. (The
same operation is carried out whether or not you press the
YES  key.)
5
After all originals have been fed through the
reversing automatic document feeder, press the
FINISHED  key.
- Copying begins.
1
Place paper in the drawer(s).  Page 2-4
2
Press the  PROGRAM  key to enter the program
menu, and press the  ADF  key. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-4USING THE SPECIAL FUNCTIONS
3
Press the  PROGRAM  key to enter the program
menu, and press the  MIXED ORIGINAL SIZES
key.
2. MIXED-SIZED ORIGINALS
 Select other copy modes as required.
6
Press the  START  key.
2
Adjust the slide to the widest paper size, and align
the originals against the left front side.
- Place the originals face up.
When placing the different-sized originals in the reversing automatic document feeder, you can make
copies by setting MIXED-SIZED ORIGINALS.
The available combination of mixed-sized originals are as follows:
 - LD (Ledger), LG (Legal), LT (Letter), LT-R (Letter-R)
* The image may be copied out of position depending on the combination.
1
Place paper in the drawer(s).  Page 2-4
- Bypass copying is not possible.
4
Press the  SET  key.
5
Select either the Automatic Paper Selection
( Page 3-2) or Automatic Magnification
Selection mode 
( Page 3-4).
- To make duplexed copies, select the automatic
magnification mode. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-5
2
Press the  PROGRAM  key to enter the program
menu, and press the  JOB MEMORY  key.
3. JOB MEMORY
Storing a Combination of Copy Job Settings
You can store and recall a combination of frequently used copy jobs at anytime.
Up to four such combinations of jobs can be stored.
* You cannot delete the copy modes that have already been stored in the memory, but you can rewrite
new jobs on the memory key in which some copy modes have already been stored.
3
Press the  MEMORY  key.
1
Select the desired copy modes.
Example :
Reproduction ratio ........... 85%
Copy quantity ................... 10 copies
Paper size ........................ LT-R (Letter-R)
4
Press the desired Memory Number key.
- The copy job settings are stored in the selected Memory
Number key.
- Memory Number keys where copy jobs have been already
stored are shown in a half-tone shaded pattern.
- The stored copy jobs remain unchanged until different copy
jobs are entered. (They are retained even after the power
switch is turned off.) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-6USING THE SPECIAL FUNCTIONS
4
Press the  RECALL  key.
3. JOB MEMORY (Cont.)
2
Place the original(s).  Page 2-9
5
Press the Memory Number key where the desired
combination of copy job settings are stored.
- Memory Number keys where copy jobs have been already
stored are shown in a half-tone shaded pattern.
3
Press the  PROGRAM  key to enter the program
menu, and press the  JOB MEMORY  key.
6
Press the  START  key.
- Copies will be made in the recalled copy jobs.
Recalling a Stored Combination of Copy Job Settings to Make Copies
1
Place paper in the drawer(s).  Page 2-4 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-7
To confirm the copy modes stored in the Memory Number key,
perform steps 3 to 5 on the previous page, then press the
SETTINGS  key.
Confirming Stored Copy Jobs
- The screen on the right is an example of jobs that have been
stored in “MEMORY 2”. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-8USING THE SPECIAL FUNCTIONS
MAX
4. BYPASS COPYING
When you want to make copies on thick paper, OHP film, tab paper, tracing paper, sticker labels, use the
sheet bypass. (Only thick and tab papers can be set in the drawer. 
 Page 2-7)
If the desired size of paper (standard size) is not set in any of the drawers, or if you want to make copies
on non-standard size, make bypass copies.
The modes below are available even in bypass copying if the paper size is specified:
- Automatic Magnification Selection - Duplex - Binding Margin - Edge Erase
- Dual-page - 2 IN 1 / 4 IN 1 - Trimming/Masking - Mirror Image
- Staple Sort - Magazine Sort - Saddle Stitch - Hole Punch
In there cases, the setting procedures of the following two sizes of paper are different.
- Bypass copying on standard size 
 Page 5-10
- Bypass copying on non-standard size 
 Page 5-11
* When copying is finished, the lamp of the  //FUNCTION CLEAR  key lights. Either press the  //FUNCTION
CLEAR  key or wait 45 seconds before the bypass copying mode automatically returns to the default
mode.
* The machine stops its operation when the paper set on the bypass guide has run out even if there is the
same size of copy paper in the drawer. The machine starts again when adding the paper on the bypass
guide before the automatic function clear mode works.
Bypass copying
The general procedure for making bypass copies (the paper size is not specified) is described below.
* In this case, the paper exits with its copied side up.
1
Set sheets of paper on the bypass guide and align
the slides with the size of the paper.
Ready for bypass feeding - This message appears:
- Acceptable paper type for bypass copy 
 Page 2-4
- Place the paper with the side to be copied facing up.
- If you put several sheets on the bypass guide at a time, fan
the papers well before placing it.
- Place the paper so as not to exceed the line indicated on
the slide.
- Do not push the paper forcibly into the entrance of bypass
feeding. It may cause paper jam.
- Draw the triple paper holder depending on the paper size.
Slide 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-9
4
After selecting the paper type corresponding to the
type of the paper that has been set, press the SET
key.
- When selecting OHP film, the hole punch mode and the
staple mode cannot be used.
If you select the paper type not corresponding to the type of
the paper that has been set, it may cause a problem such as
a paper jam, significant image deterioration, etc.
 Select other copy modes as required.
5
Press the  START  key.
3
If the paper other than standard type has been set,
press the  PROGRAM  key to enter the program
menu, and press  BYPASS FEED  key.
- If the standard size paper has been set, you do not have to
perform steps 3 to 4.
2
Place the original(s).  Page 2-9
- If you press the  MEDIA TYPE  key on the right menu, which
is displayed when placing paper on the bypass guide, the
menu of step 4 is also displayed. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-10USING THE SPECIAL FUNCTIONS
4. BYPASS COPYING (cont.)
Bypass Copying on Standard Size Paper
1
perform steps 1 to 2 on pages 5-8, 5-9.
-Set the OTHER size key as necessary.  Page 5-14
2
Press the key of the same type as the paper that
has been set.
-Non-standard size paper  Page 5-11
If the paper that has been set is a standard size other than LD,
LG, LT or ST, you will select the  OTHER  key in step 2. In this
case, you need to make the  OTHER  key recognize the same
size as the paper that has been set.
3
If you set the paper other than plain paper, press
the  MEDIA TYPE  key.
4
After selecting the media type key corresponding
to the type of the paper that has been set, press the
SET  key.
If you select the media type key not corresponding to the type
of the paper that has been set, it may cause a problem such
as a paper jam, significant image deterioration and etc.
 Select other copy jobs as required.
5
Press the  START  key. 
						

							12
3
4
5
6
78
9
10
11
12
5-11
2
Press the  NON-STANDARD  key.
1
Perform steps 1 to 3 on page 5-10.
The size of non-standard paper is within the following ranges:
  Length: 100 - 297mm (3.94” - 11.69”)   Width: 148 - 432mm (5.83” - 17.01”)
3
Key in each dimension (length and width), or recall
the data stored in the MEMORY. Then press the
lower  SET  key.
- When using the digital keys to key in the size: Key in the length and press the upper  SET  key. Similarly,set the value for the width.
- Press the  MEMORY 1  ( MEMORY 2 ,  MEMORY 3 or MEMORY 4 ) key and the paper size memorized in the
selected memory key appears.
- Storing a non-standard size in the memory
 Page 5-12
 Select other copy jobs as required.
4
Press the  START  key.
Bypass Copying on Non-Standard Size Paper
* 25.4mm = 1” 
						

							1
2
3
4
5
6
7
8
9
10
11
12
5-12USING THE SPECIAL FUNCTIONS
3
Press the desired Memory Number key.
- When the paper size is ‘0mm’, the selected Memory
Number key is vacant.
- When the paper size is displayed, a non-standard size is
already stored in the selected Memory Number key. To
delete the settings, perform step 4. New settings will be
rewritten and stored on that Memory Number key.
Storing a Non-Standard Size in the MEMORY
4
Key in each dimension, then press the  MEMORY
key.
- Key in the length and press the upper  SET  key. Similarly,
set the value for the width.
- The paper size is stored in the shaded Memory Number
key.
It is convenient if a frequently used non-standard size of paper is stored in the memory.
Bypass Copying on Non-Standard Size Paper (cont.)
4. BYPASS COPYING (cont.)
2
Press the  NON-STANDARD  key.
1
Perform steps 1 to 3 on page 5-10.