Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							1
2
3
4
5
6
7
8
9
10
11
12
7-23
7
Close the lower cover of the finisher. Test stapling
is then automatically performed on a blank sheet.
- This operation is carried out to avoid blank stitching.
If test stapling fails to be performed and the following
message remains displayed, repeat the above procedure
from steps 1 to 7.
Set staple car tridge
6
Make sure that the finisher is attached to the
machine firmly and that LD, LT-R size paper is set
in the machine.
- If one of the above paper sizes is not set, test stapling cannot
be performed. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-24WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
When copies have not been stapled in the staple mode, the following message may be shown on the
display:
Examine stapler
This means that staples have become jammed. Remove them as described below.
Finisher
6. REMOVING JAMMED STAPLES (OPTIONAL)
2
Holding the knob, lower part A.
Caution
Do not touch the stapling area.
The stapler could injure you.
3
Remove any jammed staples using your fingertip
or something sharp.
4
Holding the knob, return part A to its original
position.
A
A
Stapling area
1
Perform steps 1 to 2 on page 7-21. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-25
5
Return the staple case to its original position.
- Insert the cartridge until it is caught by the claw and fixed
with a click sound.
Saddle Stitch Unit
6
Close the front cover of the finisher.
2
Remove the empty staple case.
3
While pushing down on level
 , pull up knob
 .
1
Perform steps 1 to 3 of the procedure for
“ 5. ADDING STAPLES Saddle Stitch Unit ”
(  Page 7-24). 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-26WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
5
Return the staple case to its original position.
6. REMOVING JAMMED STAPLES (OPTIONAL) (cont.)
Jammed staples
Stapler
4
Remove any jammed staples, and then return knob
 
to its original position. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-27
7. DISPOSING OF ACCUMULATED PUNCHED PAPER BITS (OPTIONAL)
When paper bits punched from copies have accumulated to a cer tain level, the following message appears.
Please Dispose of Hole Punch Dust
Dispose of the paper bits as described below.
1
Open the cover of the hole punch unit.
2
Holding the black handle, slide out the case
containing the paper bits, and dispose of them
properly.
3
Return the waste case to its original position.
4
Close the cover of the hole punch unit. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-28WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
When the CALL SERVICE      or CLEAR PAPER    symbol is flashing, if you press the   Clear  key and
the digital key  8  together before you turn off the power, the corresponding error code will appear on the
copy quantity display only while both keys are held down. Please give the error code in addition when you
are asking for service.
Since heaters are used to fix toner images to the copy paper, a safety circuit is incorporated in this
machine. After you turn on the power switch, if a certain temperature is not attained within a specified
period of time, the safety circuit assumes that something abnormal has happened, causing the machine
to stop its operation. This can possibly occur when the temperature is low even if the machine is not
malfunctioning. If this occurs, turn the power switch off and then on again. Repeat this procedure twice,
and if the problem still persists, turn off the power switch and call for service. When the CALL SERVICE   
   symbol flashes, the following message appears and copying is no
longer possible. Call your service technician.
Call for service
8. CALL SERVICE    SYMBOL / PERIODIC MAINTENANCE MESSAGE
The following message may appear on the display panel:
Time for periodic maintenance
CALL SERVICE SYMBOL
PERIODIC MAINTENANCE MESSAGE
or
Time for periodic maintenance
(Fuser cleaning web)
This indicates that assistance from a qualified service technician is required. Call your service technician
for assistance.
Using the machine continuously without replacing the fuser cleaning web causes dirty image. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
8-1
8. MAINTENANCE
1. DAILY INSPECTION ................................................................ 8-2
2. SIMPLE TROUBLESHOOTING ............................................... 8-3
@.BJOUFOBODFQ04/09/02, 16:53 1 
						

							1
2
3
4
5
6
7
8
9
10
11
12
8-2MAINTENANCE
Scanning
area
1. DAILY INSPECTION
Items for Daily Check
Power switch ON/OFF status
We recommend turning the power switch ON at the star tup everyday so that copies can be made whenever
you want. Also, be sure to turn the power switch OFF when you leave the office. In the following cases, do
not turn the power switch OFF.
- when the off-mode (or sleep mode) is set;
- when the weekly timer is in use;
Weekly Maintenance
Cleaning the original glass, the original cover, the scanning area and the guide area.
To maintain copy quality, the following items are recommended to be cleaned preferably once a week.
- Clean the original glass with a cloth moistened with a
small amount of water or cleaning liquid, then wipe a
dry cloth over the glass.
- Be careful not to scratch the parts that you are cleaning.GuideOriginal
Cover
Original
Glass
@.BJOUFOBODFQ04/09/02, 16:53 2 
						

							1
2
3
4
5
6
7
8
9
10
11
12
8-3
Press the  START  or  ENERGY SAVER
key on the control panel to clear the automatic
energy saving mode. (It takes a while for the
machine to become ready.)
Press  
START  key to return the power
‘ON’ .
Key in the correct department code.
* If the department code is not clear, ask
your machine manager.
If you are using a key copy counter, insert it
into the slot.
Wait until the machine becomes ready. Is the machine in the automatic
energy saving mode?
Is the power ‘OFF’ because the
weekly timer is functioned?
Is the department code keyed in?
Is the department code
correct?
Is a key copy counter (optional)
used?
Is the “Warming up” message
displayed?
Reference page
Page 1-2
Items to be checked
Is the power cord plug firmly
inserted in the outlet?
Is the front cover, the side
cover and the large capacity
feeder (optional) firmly closed?
2. SIMPLE TROUBLESHOOTING
Check the following items, and if the problem still occurs, call service for assistance.
Machine does not start
Countermeasure
Insert the power cord plug firmly.
Close the covers properly.
Display does not change when keys or icons are pressed
Page 1-5, 5-16
Page 5-13
Page 5-20
Page 1-10
Page 1-8
Items to be checked
Has the message “Add toner”
appeared on the screen?
Is the copy density adjustment
set lighter than is standard?
Countermeasure
Replace the toner bottle.
Use the manual density keys to set the copy
density properly.
Copy density is too low
Reference page
Page 7-6
Page 3-11
@.BJOUFOBODFQ04/09/02, 16:53 3 
						

							1
2
3
4
5
6
7
8
9
10
11
12
8-4MAINTENANCE
Is the reversing automatic
document feeder firmly
closed?
Is the original cover or the
transport belt of the reversing
automatic document feeder
dirty?
Is the scanning area dirty?
Is the copy density set
properly?
Reference page
Page 7-3
Select the same size of copy paper as the
original, or set the reproduction ratio suitable
for the paper size.
Set a smaller image shift value. Are the original size and
direction, as well as the
reproduction ratio, suitable for
the paper size?
Is the margin on the copy set
properly?
Countermeasure
Place the original firmly on the glass and
close the reversing automatic document
feeder.
Replace with new paper.
Items to be checked
Does the entire original lie
properly on the surface of the
glass?
Is the copy paper moist?
Copy images are blurred
Images are partially missing
Page 3-2, 3-4
Page 4-2
2. SIMPLE TROUBLESHOOTING (Cont.)
Copies are stained
Close the reversing automatic document
feeder firmly to shut out any outer light.
Clean the original cover or the transport belt.
Set the copy density properly with the
AUTO  key or manual density keys.Page 2-10
Page 8-2
Page 3-11
Is the copy density adjustment
set darker than is standard?
Copy density is too high
Use the manual density keys to set the copy
density properly.Page 3-11
@.BJOUFOBODFQ04/09/02, 16:53 4