Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							12
3
4
5
6
78
9
10
11
12
2-7
8
Press the  JOB STATUS  key on the control panel,
then the  CASSETTE  key on the touch panel.
9
Press the drawer key corresponding to that in which
the paper size has been changed, then press the
key of the paper size newly set.
- Chinese paper sizes (16K, 8K and 16K-R) can be selected on the screen which appears when the  Next  key is pressed
once. Pressing the  Next  key again will display the AB format
paper sizes.
- Press the RETURN key on the touch panel or the JOB STATUS key on the control panel to return to the basic
screen.
You can set the drawer for various uses (cover sheet, sheet insertion and tab paper, thick paper special
sheets). The default paper is plain paper 
 Page 2-4
Drawer for cover sheet  Page 4-18
Drawer for sheet insertion  Page 4-20
Drawer for tab paper (must be used in second drawer)  Page 4-22
Drawer for special sheets...Colored paper, paper with a watermark, etc.
1
Place paper in the drawer(s).
- Place the paper with its face down.
- Setting tab paper 
 Page 4-22
- For changing the paper size in the drawer, follow step 1 to 9 on the previous page.
2
Press the  JOB STATUS  key on the control panel,
then the  CASSETTE  key on the touch panel. After
this procedure, press the  MEDIA TYPE  key.
Setting the Drawer for Special Uses
(To be continued) 
						

							12
3
4
5
6
78
9
10
11
12
2-8HOW TO MAKE COPIES
2. SETTING COPY PAPER (Cont.)
Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses (Cont.)
3
Press the drawer key corresponding to that in which
the paper has been set, then press the key of the
paper type newly set.
- If you want to select the  COVER ,  INSERT  or  TAB PAPER, make sure that paper with the same size as that for the
COVER, INSERT, or TAB PAPER is set in the other drawer
including the optional external LCF (Large Capacity Feeder).
Press  THICK 1  or  THICK 2  depending on the paper weight
of cover sheet, insertion, and special sheet. In the case of
cover sheet and inser tion, ‘
’ o r  ‘’ is displayed in the drawer
key.
* For example, when inserting 90 lb. Index paper, press INSERT  key, and press  THICK 1   key.
- The setting is completed as shown on the right.
Clearing the Drawer for Special Uses
Press the drawer key corresponding to that which is
set for the special use, then press the key of the same
mode as the drawer.
- If you clear INSERT 1 when both INSERT 1 and INSERT 2 are set, the drawer for INSERT 2 changes to INSERT 1.
- Replace the paper set in the drawer as required.
- Press the  RETURN  key on the touch panel or the JOB STATUS  key or either lighting one of 
 COPY   key or
 PRINTER/NETWORK  key on the control panel to return to
the machine to the basic screen (before  JOB STATUS   key is
pressed on the step 2).
Up to 2 drawers can be set for the sheet inser tion.
After having set INSERT 1, press the drawer key corresponding
to that in which the paper for INSERT 2 has been set, and
press the  INSERT  key. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
2-9
Setting place
Glass
*1
Reversing automatic
document feeder
*2
Types of originals
Sheets
Three-dimensional objects
Books
Plain paper, recycled paper:
13.3 - 33.8 lb (1-Sided Original)
13.3 - 27.7 lb
 (2-Sided Original)
Maximum size
Width: 11.6”
Length: 17”
Width: 11.6”
Length: 17”Sizes capable of
automatic detection
(Standard size)
LD, LG, LT, LT-R, ST-R
NOTE: LD: Ledger, LG:
Legal, LT: Letter, LT-R:
Letter-R, ST-R: Invoice-R
(Standard size)
LT format:
LD, LG, LT, LT-R, ST-R
Acceptable Original Types and Sizes
*1: Do not place any heavy object (8.82 lb or over) on the glass.
*2: Even listed under “Types of originals”, some of the originals may not be used depending on paper
quality.
Maximum number of sheets (all sizes) can be set in the reversing document feeder: 100 sheets (20 lb
Bond) or less than 0.62” in height.
3. SETTING ORIGINALS 
						

							1
2
3
4
5
6
7
8
9
10
11
12
2-10HOW TO MAKE COPIES
3. SETTING ORIGINALS (Cont.)
1
Raising the reversing automatic document feeder,
place the original in the direction as shown in the
illustration.
- When using the Book-Type Originals 2-sided Copies (
Page 3-8) or the Dual-Page ( Page 4-5) function, center
the book original on the yellow indicator line.
When Placing an Original on the Glass
Blank sheet
Original
Original
Sheet Originals
1
Raising the reversing automatic document feeder,
place the original face down on the glass.
2
Align the original against the left inner corner of the
glass.
3
Lower the reversing automatic document feeder
slowly.
When using the non sorting and non staple mode, the paper exits face up.
- When copying originals with high transparency, such as OHP
films and tracing paper, place a blank sheet of paper the
size of the original or larger over the original.
Book-type Originals
2
Lower the reversing automatic document feeder
slowly.
- Do not try to force the reversing automatic document feeder
to fully close over a very thick original, such as a big book.
Copies can be made even if the cover or feeder does not
close fully.
- During copying, an intense light may leak out. Do not look at
the original glass surface. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
2-11
When Using the Reversing Automatic Document Feeder
Originals in progress automatically exit on  or  depending
upon the size of originals.
..... LT (Letter), ST-R (Invoice-R)
..... LD (Ledger), LG (Legal), LT-R (Letter-R)
When the papers exit on , pull up the stopper to prevent
originals from falling.
Exiting Originals
Stopper
Precautions for Using the Reversing Automatic Document Feeder
Also, the following originals should be handled carefully:
(1) Folded or curled originals should be
smoothed out before being used.
(2) Originals, two of which, when pinched between two
fingers, cannot be moved, or originals which are
surface-treated may fail to be separated properly.
Do not use the following types of originals as they tend to misfeed or become damaged:
(1) Badly wrinkled or folded
originals; in par ticular, originals
whose leading edge is curled
may fail to be correctly fed.
(4) Clipped or stapled originals(2) Originals with carbon paper
(5) Originals with holes or torn originals (3) Taped, pasted or clipped (cut
out) originals
(6) Damp originals
* Do not use tracing paper, permeable paper and coating paper (coated with wax, etc).
* The different sized originals are limited for setting. 
 Page 5-4
If the scanning area and guide area are dirty, it may cause black streaks, etc. on the printed paper. Cleaning
them preferably once a week is recommended. 
 Page 8-2(7) OHP film originals 
						

							1
2
3
4
5
6
7
8
9
10
11
12
2-12HOW TO MAKE COPIES
When the number of originals is too large to be set at one
time, you can divide the originals into two to ten sets and
set them one after another. To do so, place the first set of
originals first, and press the  CONTINUE  key while the
scanning is in progress. After they have been scanned,
place the previous set of originals.
When Using the Reversing Automatic Document Feeder (Cont.)
 In the Single-Feed Mode  Page 5-3
2
Insert the original face up and straight along the
slides; it will then be pulled in automatically.
- When the original starts being pulled in, let go of it.
Slide
Slide
In the Continuous Feed Mode  Page 5-2
1
After aligning the edges of originals well, place
them face up and align the slides to the width of
the originals.
- Align the originals in the order from the top because they
will be fed from the top.
- One original sheet is also acceptable.
- Maximum number of sheets (all sizes) can be set in the
reversing automatic document feeder: 100 sheets (20 lb
Bond) or less than 0.62” in height.
- Be sure to set only originals with the same size. Mixed-sized originals  Page 5-4
1
Align the slides to the desired original size.
3. SETTING ORIGINALS (Cont.) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
2-13
4. AUTO JOB START (JOB PRESET)
While multi-copying is in process, you can reserve the next copy.
1
Place the original(s). Page 2-9
2
Press the  START   key.
- Up to 5 jobs including the current printing job can be
stored in the memory. Place the originals of the 6th job on
the original glass or the reversing automatic document
feeder and press the  
START   key. The following
message will appear:
 Select copy modes as required.
Auto Start
 Confirming and Cancelling Auto Job Start
Cancelling the job while waiting for the original to be stored
in the memory.
If you want to cancel copying the original when it has
already been set on the glass or the reversing automatic
document feeder and the following message is displayed:
Auto Start
press the  
FUNCTION CLEAR  or the  STOP   key.
Cancelling the job while waiting for the original to be copied.
Deleting the data waiting to be printed (except for the case above)
 Page 2-15
Confirming auto job start
Press the  JOB STATUS  key on the control panel, then the
 JOB LIST  key on the touch panel. 
						

							12
3
4
5
6
78
9
10
11
12
2-14HOW TO MAKE COPIES
5. INTERRUPT COPYING
4
After you have finished interrupt copying, press the
INTERRUPT  key again.
- The following message appears:
Select other copy modes as required.
3
Press the  START  key.
While multicopying is in progress, you can interrupt it and make copies from different originals.
* The following modes cannot be used with interrupt copying.
- Cover sheet copying - Sheet insertion copying - Document storage - Overlay
2
Replace the original with a new one.  Page 2-9
1
Press the  INTERRUPT  key.
- This message appears:
Without performing step 4, the interrupt copying mode will
automatically be cancelled and the previously interrupted
copy job will resume in a certain period of time after the
interrupt copying has finished. Job interrupted job 1 saved
- Interrupt copying is available while copying is in progress.
When the above message is displayed, you cannot make
interrupt copying.
Ready to resume job 1
Auto Star t 
						

							12
3
4
5
6
78
9
10
11
12
2-15
1
Press the  STOP  key on the operational panel
during the multicopying operation.
If you want to stop the operation during scanning or multicopying, use the   STOP  key.
 Stopping the Scanning of the Original
1
Press the control panel   STOP   key on the opera tional
panel during the scanning.
2
If the screen on the right appears, press the
MEMORY CLEAR  key.
Or press the  START  key if you want to restart the
copy operation.
 Stopping a Multicopying Operation
6. STOPPING THE COPY OPERATION
3
The data will be deleted and the multicopying
operation will stop.
- If there is other data waiting to be printed, will start being output.
2
Press the  Delete  key. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
2-16HOW TO MAKE COPIES
If data is waiting to be printed, you can delete them, or change the printing order.
7. DELETING OR CHANGING ORDER OF PENDING JOBS
Deleting the Job
In the following procedure, you can delete the multicopying operation as well.
1
Press the  JOB STATUS  key on the control panel,
then the  JOB LIST  key on the touch panel.
2
Select the job you want to delete, then press the
DELETE  key.
3
Press the  Delete  key.
4
The job will be deleted.
Press the  JOB STATUS  key or either lighting one of  COPY
key or  
 PRINTER/NETWORK   key on the control panel to
return the basic screen (before  JOB STATUS   key is pressed
on the step 1). If there is no job waiting to be printed, you
can also return to the basic screen by pressing the RETURN
key on the touch panel.
The menu on the right shows an example of the queue.