Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							1
2
3
4
5
6
7
8
9
10
11
12
7-13
6
Remove any misfed paper.
- If any paper is misfed in the cover, pull it out.
Caution
Do not touch the metal area of guide plate in the automatic
duplexer. You might burn yourself.
- If any paper is misfed in the machine, open the front cover
and remove any misfed paper by turning the knob in the
direction of the arrow.
Metal area of
guide plate
Metal area of
guide plate
5
Open the exit cover.
- For how to connect or separate the optional finisher.
Page 7-9
7
Turn the handle in the direction of the arrow.
- If any paper is misfed in the position on the right, pull it
out. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-14WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
Metal areaFuser unit
- If a sheet of paper is misfed on the transfer belt, remove it.
- Do not put some objects on the transfer belt or do not touch
it.
- When a sheet of paper is caught in fuser unit, do not pull out
directly but remove based on step 9.
10
Pick the lever of the transfer unit as shown on the
right and open the bottom (automatic duplexer).
8
Pull the transfer unit out until it comes to a stop.
9
Lift the grip, then turn the knob in the direction of
the arrow to remove any misfed paper.
Caution
Do not touch the fuser unit and around the metal area. You
may be burned or be injured if you come into contact with the
inner area in the fuser due to high temperature.
11
Remove any misfed paper.
4. CLEAR PAPER    SYMBOL (Cont.) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-15
1
Pull up the misfed paper slowly on the bypass guide.
 Paper Misfeed on the Bypass Guide
 Paper Misfeed in the External LCF (Large Capacity Feeder) (Optional)
2
Remove any misfed paper by turning the blue knob
in the direction of the arrow.
1
Pull the external LCF away from the machine slowly
while pressing the release lever.
3
When paper misfeeds inside of the machine, pull
up and out the misfed paper.
- If unable to easily pull out the misfed paper, open the
bypass guide cover and pull  A , then remove the misfed
paper.
Blue knob
A 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-16WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
4
Open the cover of the external LCF and remove any
misfed paper.
- Be careful not to touch the drawer slide rail.
Be careful not to let your fingers be caught when closing the
drawer.
5
Return the external LCF to its original position.
- As shown in the figure on the right, place your hands on B
to enable you to slowly reconnect it to the machine while
maintaining both machines parallel to one another.
When installing the external LCF, be careful not to let your
fingers be caught between it and the machine.
B
Slide rail
4. CLEAR PAPER    SYMBOL (Cont.)
  Paper Misfeed in the Hole Punch Unit (Optional)
1
Open the cover of the hole punch unit.
A2
Rotate the blue knob to locate the arrow within the
area 
A on the label.
- Under this condition, the punchers are up, allowing the
paper shown in the figure to be removed. 
						

							12
3
4
5
6
78
9
10
11
12
7-17
Knob
2
1
2
Lift knob  (See the upper right figure), then
remove any misfed paper.
- For the paper misfed in the position shown on the right, pull the knob in the direction of the arrow, then remove it.
Knob 
Knob 
  Paper Misfeed in the Finisher (Optional)
1
Open the upper cover of the finisher.
Knob
3
Lift knob  and then remove any misfed paper.
( is indicated in the illustration of step 2) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-18WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
4. CLEAR PAPER    SYMBOL (Cont.)
4
Remove any misfed paper from the paper exit area.
  Paper Misfeed in the Saddle Stitch Unit (Optional)
* Only when the saddle stitch finisher (DA-FS815) is installed.
1
Open the entrance cover of the saddle stitch unit.
2
Remove any misfed paper.
3
Open the lower cover of the finisher. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-19
12
4
Turn the right-hand knob  counter clockwise. Then,
push the left-hand knob 
 and turn it clockwise.
5
Remove any paper misfed on the exit side of the
saddle stitch unit.
6
Open the exit cover of the saddle stitch unit and
remove any misfed paper. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-20WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
5. ADDING STAPLES (OPTIONAL)
When the staple cartridge runs out of staples, if the optional finisher is installed, the following message
appears:
Set staple cartridge
Add staples to the cartridge according to the procedure below.
2
Lower the blue lever in the stapler and slide out
the staple cartridge.
- The stapler unit has moved to its specified position.
- Do not move the stapler unit while performing the above
procedure, or it will be broken.
3
Remove the empty staple case upward from the
staple cartridge.
4
Push in a new staple case into the staple cartridge
completely inside until a click is heard.
- Do not remove the seal holding the staples until the staple
case is set in the cartridge.
Finisher (DA-FS810/FS815)
1
Open the front cover of the finisher. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-21
5. ADDING STAPLES (OPTIONAL) (Cont.)
6
Return the staple cartridge to its original position.
- Insert the cartridge until it is caught by the claw and fixed
with a click sound.
7
Close the front cover of the finisher.
If the following message remains displayed, repeat the above
procedure from 
 to .
Set staple cartridge
5
Pull out the seal holding the staples straight
upward. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-22WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
3
Pull out the grip of the saddle staple holder 
toward you and turn it  90o clockwise in the
direction of the arrow.
4
Remove the empty staple case and set a new one.
- Replace both staple cases with new ones.
- Do not remove the seal holding the staples before the staple
case is set in the cartridge.
5
Return the saddle stitch holder and the saddle stitch
unit to their respective original positions.
2
Slide out the saddle stitch unit carefully toward the
front.
Saddle Stitch Unit
* Only when the Saddle-Stitich Finer (DA-FS815) is installed.
1
Open the lower cover of the saddle stitch finisher.
5. ADDING STAPLES (OPTIONAL) (Cont.)