Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							1
2
3
4
5
6
7
8
9
10
11
12
7-3
Side guide
Approx. 0.5mm Approx. 0.5mm
Side guide
Slide Rail 
Adding Paper to the Drawers
1
Pull the drawer out carefully until it comes to a
stop.
- Be careful not to touch the drawer slide rail.
2
Place the paper in the drawer.
- Place the paper face down.
- Maximum number of sheets that can be set. 
 Page 2-4
- Fan the paper well before placing it in the drawer.
- Do not add paper above the line indicated on the guide.
- Do not use creased, folded, wrinkled or damp sheets of
paper.
3
Push the drawer straight into the machine until it
comes to a stop.
- Be sure to push the drawer carefully and fully in.
Be careful not to let your fingers be caught when closing the
drawer.
When the paper supply in the selected drawer or Tandem LCF (Large Capacity Feeder) runs out, the
drawer or External LCF (Large Capacity Feeder) (optional) shown on the display flashes, and the
following message appears:
Add paper
Add paper as follows.
2. ADD PAPER SYMBOL
Make sure that a gap of approx. 0.5 mm (less than 1 mm in
total) is left between the paper and the side guide. If there is
no gap, this may cause paper misfeeding. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-4WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
MAX
Slide Rail 
A
B
1
Pull the tandem LCF out carefully until it comes to
a stop.
- Be careful not to touch the drawer slide rail.
2
Open some packages of paper, take out entire reams
of paper and set them aligned in tray 
A and tray B.
- When setting the paper, set the paper for A to the right
side, and set it for 
B to the left side. (The paper can be
set neatly if you pile it up gradually and alternately in trays
A  and B.) Be sure that the center lever is not open (refer
to the labels attached in the tandem LCF ).
- Up to 2500 sheets of paper (20 lb Bond) can be set.
- Paper starts being fed from the elevator tray 
A at first,
and when it runs out of paper, the paper on tray 
B moves
to the position A.
- Set the paper so that it does not protrude beyond the line
of indication shown on the rear guide plate.
- Do not use creased, folded, wrinkled or damp sheets of
paper.
- Be careful not to touch the drawer slide rail.
3
Close the cover of the tandem LCF.
- Close the drawer completely. The elevator tray automatically
moves up to the paper feeding position.
Be careful not to let your fingers be caught when closing the
drawer.
2. ADD PAPER SYMBOL (Cont.)
Adding Paper to the Tandem LCF (Large Capacity Feeder) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-5
MAX
Slide Rail 
Adding Paper to the External LCF (Large Capacity Feeder) (optional)
1
Pull the external LCF out carefully until it comes to
a stop.
- Be careful not to touch the drawer slide rail.
2
Place the paper on the elevator tray.
- Place the paper face up.
- Maximum number of sheets that can be set 
 Page 2-4
- Fan the paper well, then place it on the elevator tray, aligning
it on the rear guide tray.
- Set the paper so that it does not protrude beyond the line of
indication shown on the rear guide plate.
- Do not use creased, folded, wrinkled or damp sheets of
paper.
Do not touch the Elevator Tray while it is moving.
3
Close the cover of the external LCF.
- Close the cover completely. The elevator tray automatically
moves up to the paper feeding position.
Be careful not to let your fingers be caught when closing the
drawer.
Elevator Tray 
						

							12
3
4
5
6
78
9
10
11
12
7-6WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
Here at Panasonic dependable high quality image output is what we do. By using genuine Panasonic
toner you can ensure that you are not only receiving quality output but also output that is friendly to
mother ear th and human beings.
1
Open the front cover.
When the toner bottle runs out of toner, the REPLACE TONER
BOTTLE  
  symbol flashes,
Add toner
This message will appear on the screen.
3. REPLACE TONER BOTTLE    SYMBOL 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-7
Label (orange)
Shutter (orange)
Holder
2
Rotate the left end of the holder, then pull out the
empty toner bottle with both hands as shown on
the right.
Return used toner bottles to your service technician.
3
Shake the new toner bottle well to loosen the
toner inside.
4
Holding the new toner bottle as shown on the right,
pull out the seal in the direction of the arrow.
5
Match the label (orange) on the machine with the
shutter (orange) on the toner bottle, then insert
the toner bottle to the end.
- If you cannot insert the toner bottle completely, rotate it
slightly to check the position and insert it again.
- If the toner scatters, wipe it off completely.
6
Return the toner bottle holder back to its original
position.
7
Close the front cover.
- The following message appears:
Wait adding toner
The machine automatically star ts supplying toner.
- When toner has finished being supplied, the touch panel
returns to the basic menu and the current job automatically
resumes. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-8WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
Type of Originals
A.
B.
C.
A
20,00030,00040,00050,000 60,000 70,00074,000
A
20,00030,000 40,000 46,000
B
20,000 27,00015,000
C
A
20,00030,000 38,000
Replace Toner  Bag
- When the toner bag becomes full of used toner, the
REPLACE TONER BAG  
  symbol flashes. Please call
your service technician to ask to have the used toner bag
replaced with a new one.
Dispose of Used Toner
The life of the toner bottle (number of copies) varies depending on the following conditions.
Coverage of originals (printing ration of copies) varies depending on the following conditions:
1. Size and density of originals
2. The existence of solid black when making copies (when a book is copied and the original cover is
par tially open)
3. Temperature and humidity in the room when making copies
4. Copy density and image quality mode
As indicated in the figure below, the life of the toner bottle varies depending on the copy mode and the
coverage of the originals
Additional Explanation
3. REPLACE TONER BOTTLE    SYMBOL (Cont.) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-9
Reversing Automatic Document Feeder
Inside of the Machine
Bypass Guide
External LCF (Optional)
Hole Punch Unit (Optional)
Finisher (Optional)
Saddle Stitch Unit (Optional) When a paper misfeed occurs in the machine, the  
  or    symbol flashes in the positions where the
paper is misfed. In that case, remove the misfed paper using the following procedure referring to the
illustration below.
4. CLEAR PAPER    SYMBOL 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-10WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
 Paper Misfeed in the Reversing Automatic Document Feeder
2
Rotate the blue knob to remove any misfed
originals.
1
Push the button on the reversing automatic
document feeder to open the cover.
3
Lift the blue handle (first) as shown on the right.
- If there are any misfed originals, remove them.
4. CLEAR PAPER    SYMBOL (Cont.) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-11
7
Lifting the handle in the direction of the arrow, pull
it toward you.
6
Open the original exit tray and remove any misfed
originals.
8
Remove any misfed originals.
5
Lift the original feeding tray and remove any misfed
originals.
4
Lift the blue handle (second) as shown on the right.
- If there are any misfed originals, remove them. 
						

							1
2
3
4
5
6
7
8
9
10
11
12
7-12WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL
 Paper Misfeed inside of the Machine
1
Open the paper feed cover.
- When installing the external LCF (Optional), open the paper
cover after doing step 1 of page 7-15.
3
Open the bypass cover.
2
Remove any misfed paper.
4
Remove any misfed paper.
4. CLEAR PAPER    SYMBOL (Cont.)