Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

							12
3
4
5
6
78
9
10
11
12
3-9
3
Select the book copying type.
- Press the  RIGHT RIGHT  key if copying should start at a
right-hand page and end at a right-hand page. By the same
token, you can choose from among the  RIGHT
 LEFT ,
LEFT
 LEFT  and  LEFT RIGHT  keys.
2
Press the  BOOK 2  key.
6
Place the first page(s) to be copied on the glass,
and press the  
START  key.
- If you do not copy your originals from the first page, the copies will not be arranged in the same order as the original.
- Center the book on the yellow indicator line with its bottom toward you.
4
Select LT copy size.
5
If you need a binding space, select the book margin
mode from the Image Shift function.
 ( Page 4-2)
 Select other copy modes as required.
Indicator line
(To be continued) 
						

							1
2
3
4
5
6
7
8
9
10
11
12
3-10SETTING OF BASIC COPY MODES
7
Turn to the next page, set the book again and press
the  
START  key.
- Repeat the procedure above until all your originals have
been scanned.
8
After all your originals have been scanned, press
the  FINISHED  key.
- Press the  COPY FINAL PAGE  key if the last original has
only one page.
3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE) (Cont.) 
						

							12
3
4
5
6
78
9
10
11
12
3-11
- If the automatic density mode is not selected, press the MANUAL  key, then press the  AUTO  key on the next
screen.
4. COPY DENSITY ADJUSTMENT
There are two types of image density adjustments: automatic mode (default setting) and manual mode. In
the automatic mode, the sensors automatically detect the density of each original and select the optimum
image density. In the manual mode, you can select the desired level of image density. It is recommended
that lighter-density original be coped in the manual copy density mode.
3
Confirm that “AUTO” is displayed on the basic
screen.
1
Place paper in the drawer(s). Page 2-4
Automatic Copy Density Mode
2
Place the original(s). Page 2-9
 Select other copy modes as required.
4
Press the  START  key. 
						

							12
3
4
5
6
78
9
10
11
12
3-12SETTING OF BASIC COPY MODES
4. COPY DENSITY ADJUSTMENT (Cont.)
- When the DENSITY LEVEL key is shown on the lower left of the screen, you can adjust the density manually on the
basic screen.
4
Press either  or  key to adjust the copy density
to the desired level.
- Each time you press the  or  key, your copies will
become lighter or darker, respectively.
3
Press  AUTO  on the basic screen.
Manual Copy Density Mode
1
Place paper in the drawer(s).  Page 2-4
2
Place the original(s).  Page 2-9
 Select other copy modes as required.
5
Press the  START  key. 
						

							12
3
4
5
6
78
9
10
11
12
3-13
5. SELECTING ORIGINAL MODE
According to the type of your originals, you can choose among the three image types: Photo, Text or Text/
Photo (default setting). The Photo mode is suitable for copying photo originals whereas the Text mode is
preferable for copying originals containing text only (or text and line artwork only). The Text/Photo mode
is to be selected for originals containing photo and text mixed together.
 Select other copy modes as required.
5
Press the  START  key.
The amount of toner consumed varies depending on the
selected image of toner mode. 
 Page 7-8
- The amount of toner consumed by copying the same original is in the following order:
‘PHOTO’ < ‘TEXT/PHOTO’ < ‘TEXT’
(Lest to most consumed toner)
1
Place paper in the drawer(s).  Page 2-4
2
Place the original(s).  Page 2-9
3
Press the key (shaded) on the right basic screen.
4
Choose the desired image type mode by pressing
one of the  PHOTO ,  TEXT , and  TEXT/PHOTO
keys. 
						

							12
3
4
5
6
78
9
10
11
12
3-14SETTING OF BASIC COPY MODES
6. QUICK ACCESS MENU
Finishing copy and duplex modes can be performed at the same time on one display by pressing the
QUICK button. The character and button sizes are enlarged, and the white characters are displayed on
the black background in order that you can easily operate the machine.
“Quick menu Display” and “Initial Screen” can be changed on the User Selection ( Page 5-19).
 Set up other copying modes as required.
4
Press the  START  key.
For the functions of the finishing and duplex modes, which
are not shown on the display, set them on the basic screen.
- Finishing mode setting 
 Page 6-2
- Duplex copying 
 Page 3-7
3
Press the   QUICK   button to display the menu
shown on the right, then press a button to perform
one of the functions.
- The right menu shows “Non-sort and non-staple” and “one side of the original is copied on one side of a sheet of paper.”
- For the details of the functions, refer to the pages below. [Finishing Mode]
Staple sor t (staple at one corner) 
 Page 6-4
Sort 
 Page 6-3
[Duplex Mode] 
 Page 3-7
1
Place paper in the drawer(s).  Page 2-4
2
Place the original(s).  Page 2-9 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-1
4. USING THE EDITING
FUNCTIONS
1. IMAGE SHIFT .......................................................................... 4-2
2. EDGE ERASE .......................................................................... 4-4
3. DUAL-PAGE ............................................................................. 4-5
4. X-Y ZOOM ............................................................................... 4-7
5. IMAGE EDITING ...................................................................... 4-8
- Trimming/Masking...................................................................................... 4-8
- Mirror Image............................................................................................. 4-10
- Negative/Positive Reversal ....................................................................... 4-11
6. 2 IN 1 / 4 IN 1 ......................................................................... 4-12
7. COPYING WITH ANNOTATION ............................................. 4-14
8. PAGE NUMBERING COPYING ............................................. 4-15
9. MAGAZINE SORT (FROM THE EDITING MENU) ................. 4-16
10.COVER COPYING ................................................................. 4-18
11.TAB PAPER MODE ................................................................ 4-20
12.DOCUMENT STORAGE ........................................................ 4-26
13.OVERLAY .............................................................................. 4-28
14.SHARPNESS ADJUSTMENT ................................................ 4-31
15.DIRECTION OF DUPLEX COPY IMAGES (Rotation) ........... 4-32 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-2USING THE EDITING FUNCTIONS
1. IMAGE SHIFT
1
Place paper in the drawer(s).  Page 2-4
- When using this mode in bypass copying, be sure to specify
the paper size. 
 Page 5 -10, 5 -11
A margin for binding is created by shifting the original image to either the right or left side. You can also
create binding margins in the center (inner margin) when using Book-Type Originals to 2-sided copies
(
 Page 3-8).
4
Press the  LEFT  or  RIGHT  key according to your
desired binding side.
Providing Right or Left Margin
3
Press the  EDIT  key to enter the edit menu, and
press the  IMAGE SHIFT  key.
2
Place the original(s).  Page 2-9 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-3
1
Press the  EDIT  key to enter the edit menu, and
press the  IMAGE SHIFT  key.
3
Adjust the width of the margin, then press the SET
key.
- The default width of the margin is 14mm (0.551”).
- To adjust the width, press the  
 2mm  or  30mm   key to
select the desired number, then press the  SET  key.
2
Press the  BOOK  key.
5
Adjust the width of the binding margin, then press
the  SET  key.
- The default width of the margin is 7mm (0.276”).
- To adjust the width, press the  
 0mm  or  40mm   key to
select the desired number, then press the  SET  key.
- In duplex copying, margins on the back are created on the
other side of those in the front. Duplex copying
 Page 3-7
When Book Margin is selected, use it in conjunction with Book-Type Originals to 2-Sided Copies.
 Page 3-8
Providing a Bookbinding Margin
 Select other copy modes as required.
6
Press the  START  key.
*25.4mm = 1”
*25.4mm = 1” 
						

							1
2
3
4
5
6
7
8
9
10
11
12
4-4USING THE EDITING FUNCTIONS
3
Press the  EDIT  key to enter the edit menu, and
press the  EDGE ERASE  key.
 Select other copy modes as required.
5
Press the   START  key.
2. EDGE ERASE
If your original has a dirty or torn edge, it may be reproduced as a black mark on the copy. In that case,
use Edge Erase Copying. A white border is created along the edges of the copy, eliminating those black
marks.
* This function is available in only case of the standard-size original.
1
Place paper in the drawer(s).  Page 2-4
- When using this mode in bypass copying, be sure to specify
the paper size. 
 Page 5 -10, 5 -11
2
Place the original(s).  Page 2-9
*25.4mm = 1”
4
Adjust the width of the white border, then press
the  SET  key.
- The default width of the white border is 5 mm (0.197”).
- To adjust the width, press the  
 5mm  or  20mm   key to
select the desired number, then press the  SET  key.