NEC Neax 2400 Imx Circuit Card Manual
Have a look at the manual NEC Neax 2400 Imx Circuit Card Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 2 ND-70182 (E) Page 36 Revision 4.0 SN1455 CPRAQ-A/SN1531 CPRAS-A CPU Board 5. Switch Settings Note:Make-busy of this circuit card is not allowed while the Floppy Disk Drive or Hard Disk Drive is being accessed. SWITCH NAMESWITCH NO.SETTINGSTANDARD SETTINGMEANING SW (PWR)—ON×PWR is supplied to the CPR. OFF PWR is not supplied to the CPR. MB Note (FDD/HDD)—ON (Up) Make-busy of the FDD/HDD. OFF (Down)×Normal setting. MBR (DSP)—ON (Up)Make-busy Request of the CPR in which GT is located. OFF (Down)×Normal setting. CPURST (DSP)——Execute the CPR processing according to the SENSE setting. SYSTEM SELECT0 (DSP)1OFF×Not used 2OFF×Not used 3OFF×Not used 4ON Watchdog Timer time-out is not detected. OFF×Watchdog Timer time-out is detected. SYSTEM SELECT1 (DSP)1ON PCI Card (Slot 0) MBR ON. OFF PCI Card (Slot 0) MBR OFF. 2ON PCI Card (Slot 1) MBR ON. OFF PCI Card (Slot 1) MBR OFF. 3ON PCI Card (Slot 2) MBR ON. OFF PCI Card (Slot 2) MBR OFF. 4ON PCI Card (Slot 3) MBR ON. OFF PCI Card (Slot 3) MBR OFF. 5~7 OFF×Fixed to “OFF.” 8ON IMX-U System OFF 1 IMG/4 IMG System SYSTEM SELECT2 (DSP)1~8 OFF×Not used
ND-70182 (E) CHAPTER 2 Page 37 Revision 4.0 SN1455 CPRAQ-A/SN1531 CPRAS-A CPU Board Note: The SENSE switch designates the CPR processing status. The new processing status starts when the CPRRST switch on the DSP is pressed while setting the SENSE switch. SWITCH NAMESETTINGSTANDARD SETTINGMEANING SENSE (DSP) Note1The following three processes are executed at the FDD/HDD. HD formatted File copied from FDD to HD Directory created on the HD 2×On-line mode. 3 File copied from FDD to HD within the FDD/HDD. 4 Directory created on the HD of the FDD/HDD. 5OAI memory cleared, and the CPR started up in ON LINE mode by loading the ROM data. 6 HD format of the FDD/HDD. C The CPR starts up in OFF LINE mode by loading the ROM data.
CHAPTER 2 ND-70182 (E) Page 38 Revision 4.0 SN1455 CPRAQ-A/SN1531 CPRAS-A CPU Board 6. External Interface See the NEAX2400 IMX Installation Manual. 7. Switch Setting Sheet SWITCH NAME SWITCH SHAPE REMARKS SW (PWR) MB (PWR:PZ-PW106) MB (FDD/HDD) MBR (DSP) SYSTEM SELECT0 (DSP) SYSTEM SELECT1 (DSP) SYSTEM SELECT2 (DSP) SENSE (DSP) ON OFF ON ON ON 1234ON 1234ON5678 1234ON5678
ND-70182 (E) CHAPTER 2 Page 39 Revision 4.0 PH-GT10 Input Output Gate PH-GT10 Input Output Gate 1. General Function The PH-GT10 circuit card provides the TSW I/O bus interface for permitting the CPU board to control the TSW, HSW, and PLO cards within the Inter-node Switch Module (ISWM) of the ISW. Additionally, this circuit card is equipped with the copy function to be consistent with the data of TSW I/O bus in both systems (single/dual). This circuit card is used for the IMX-U system. Figure 2-12 Location of PH-GT10 (IOGT) HSW01 HSW00 TSW03 TSW02 TSW01 TSW00 LANI LANI LANI LANI HSW11 HSW10 TSW13 TSW12 TSW11 TSW10 PLO 1 PLO 0 RES CPUCPU MISC IOC EMARES RESRES (IOGT1) PH-GT10 (IOGT0) PH-GT10 ISAGTISAGT MISC I/O BUSISAGT BUS ISAGT BUSLPM TSW I/O BUS TSW I/O BUSISWM
CHAPTER 2 ND-70182 (E) Page 40 Revision 4.0 PH-GT10 Input Output Gate 2. Mounting Location/Condition This circuit card can be mounted in the shaded slots shown below. 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors are shown in Figure 2-13. Figure 2-13 Face Layout of PH-GT10 (IOGT) ISWMMounting Module 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 IOGT(#0) IOGT(#1) MB MBR OPE/MB PWRALM CA4L COPY
ND-70182 (E) CHAPTER 2 Page 41 Revision 4.0 PH-GT10 Input Output Gate 4. Lamp Indications The contents of lamp indications on this circuit card are shown in the table below. 5. Switch Settings Standard settings of switches on this circuit card are shown in the table below. 6. External Interface See the NEAX2400 IMX Installation Manual. 7. Switch Setting Sheet LAMP NAME COLOR MEANING TSW ACTGreen Lights when this circuit card is in ACT state. OFF This circuit card is in ST-BY state. Red Lights when this circuit card is in make-busy state. PWRALM Red Lights when On-Board Power Supply for this circuit card is abnormal. CA4L Red Lights when 4MHz clock supplied for Local I/O Bus is faulty. COPY Green Lights when this circuit card is in COPY mode. SWITCH NAMESETTINGSTANDARD SETTINGMEANING MBUP Circuit Card make busy DOWN×Circuit Card make busy cancel MBR UP Make busy request DOWN×Make busy request cancel SWITCH NAME SWITCH SHAPE MB Note:Normal operating mode is down. MBR Note:Normal operating mode is down. ON ON
CHAPTER 2 ND-70182 (E) Page 42 Revision 4.0 PA - P C 9 4 Data Link Multiplexer PA - P C 9 4 Data Link Multiplexer 1. General Function This circuit card mainly provides the two functions: 1) collection of BLF/TGBL information (associated with Attendant/Desk Console operation) from DLKC cards of all nodes in an IMX-U system, and 2) distribution of the collected data to ATI cards of all nodes. While a DLKC card can manage this processing solely on an accommodated node basis, the use of this card makes possible the BLF/TGBL management even on a system basis, via the Inter-node Switch (ISW). Note that this card is mounted in a PIM of any node, and if necessary, can have an optional dual configuration. For details on BLF/TGBL information, refer to the following service features explained in the “Feature Programming Manual”. Busy Lamp Field-Flexible [B-2] Trunk Group Busy Lamp [T-9] Figure 2-14 Location of PA-PC94 (DLMX) IMX-U System AT I AT I AT I AT I (TSW 1)(TSW 1) (TSW 1) (TSW 1) TSW/HSW 1 DLMX 0(DLMX 1)IN OUT DLKC 0(DLKC 1) DLKC 0(DLKC 1) DLKC 0(DLKC 1) DLKC 0(DLKC 1) TSW 0TSW 0 TSW 0 TSW 0 TSW/HSW 0 LN 0LN 1 LN 2 LN 3 ISW Note : Circuit Card : Circuit Card (No. 1 System) : BLF/TGBL data from DLKC : BLF/TGBL data to ATI : BLF/TGBL data to ATI (No. 1 system) : BLF/TGBL data from DLKC (No. 1 system) BLF: Busy Lamp Field - Flexible TGBL: Trunk Group Busy Lamp Note:IN - DLMX card gathers BLF/TGBL information from DLKC card of each node, via ISW. OUT - DLMX card sends the collected BLF/TGBL information to ATI card(s) of each node, via ISW. This figure shows an example where a pair of DLMX cards (No. 0/No. 1 system) is accommodated in a PIM of LN0.
ND-70182 (E) CHAPTER 2 Page 43 Revision 4.0 PA - P C 9 4 Data Link Multiplexer 2. Mounting Location/Condition When this circuit card is used in a single configuration. Mount this circuit card in any of the shaded slots Mounting conditions of this circuit card are as follows: 1. This circuit card cannot be mounted in Slot 05, 07, 09, 10, 11, 12, 16, 18, 19, 21, 22, 23. 2. This card is used in odd-number group (G) of the shaded slots above. 3. To used this card, be sure to assign “RT=938” on the ASDT command. 4. Do not mount another line/trunk circuit card in a slot adjoining the DLMX card within the same Highway Block (HW) (i.e. do not mount other line/trunk card in the right side of the slot where a DLMX card is mounted). When this circuit card is used in a dual configuration. Mount this circuit card in any of the shaded slots: Mounting conditions of this circuit card are as follows: 1. A pair of DLMX card No. 0/No. 1 systems must be mounted in the same Highway Block (HW). 2. This circuit card cannot be mounted in 32-port slot (10, 11,12, 21, 22, 23). 3. This card is used in odd-number group (G) of the shaded slots above. 4. To use this card, be sure to assign “RT = 9 3 8” on the ASDT command. HW 0HW 1HW 2HW 6HW 7HW 8 Highway block DLMXDLMXDLMXDLMXDLMX 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 1918 20 21 22 23 DLMX Mounting ModulePIM Mounting Condition HW 0HW 1HW 2HW 6HW 7HW 8 Highway Block 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 1918 20 21 22 23 DLMX #0 DLMX #1 DLMX #0 DLMX #1 DLMX #0 DLMX #1 DLMX #0 DLMX #1 DLMX #0 DLMX #1 DLMX #0 DLMX #1 Mounting ModulePIM Mounting Condition
CHAPTER 2 ND-70182 (E) Page 44 Revision 4.0 PA - P C 9 4 Data Link Multiplexer 3. Face Layout of Lamps and Switches The face layout of lamps and switches is shown in Figure 2-15. Figure 2-15 Face Layout of PA-PC94 (DLMX) 4. Lamp Indications The contents of lamp indications on this circuit card are shown in the table below: LAMP NAME COLOR STATE OPE Green Remains lit while this circuit card is in normal operation. ACTGreen Lights when this circuit card is in a active state. OFF Off when this circuit card is in a stand-by state. LYR OFF Off when this circuit card is in normal operation. LB OFF Off when this circuit card is in normal operation. LOAD OFF Off when this circuit card is in normal operation. PWALM Red Lights when OBP alarm ACT PWALMLOADLBLY R MB KEYOPE MNT MODE
ND-70182 (E) CHAPTER 2 Page 45 Revision 4.0 PA - P C 9 4 Data Link Multiplexer 5. Switch Settings Standard settings of switches on this circuit card are shown in the table below. 6. Switch Setting Sheet SWITCH NAMESWITCH No.SETTINGSTANDARD SETTINGMEANING MBUP Circuit card make-busy. DOWN Circuit card make-busy cancel MNT0OFF×Fixed to OFF. 1OFF×Fixed to OFF. 2OFF×Fixed to OFF. 3ON Make-busy-request. OFF Cancel the make-busy-request. MODE0×Standard setting. (TSW fixed connection) 1-7 Not used SWITCH NAMESWITCH SHAPE REMARKS MB MNT MODE ON 0 1 2 3 ON 0