Home > NEC > Communications System > NEC Neax 2400 Imx Circuit Card Manual

NEC Neax 2400 Imx Circuit Card Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx Circuit Card Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							CHAPTER 3 ND-70182 (E)
    Page 166
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    PH-CK16-A
    Phase Lock Oscillator
    1. General Function
    This circuit card, used together with a direct digital interface circuit card, sets up network synchronization.
    With this circuit card, the system can be a clock subordinate office of the digital network. As seen in the
    figure below, the PLO can be redundant regardless of the system switching network selection. This circuit
    card is used for the IMX-U system. 
    						
    							ND-70182 (E) CHAPTER 3
    Page 167
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    Figure 3-10   Location of PH-CK16-A (PLO) 
    LN0
    (IMG2/IMG3)LN3
    (IMG2/IMG3)
    32M, FH+WFH
    PLO ACT32M, FH+WFH
    PLO ACT
    CLK1
    (TSWM1)
    TSW
    10~13
    CLK0
    (TSWM1)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    HSW00 ISW
    HSW01
    CLK1
    (TSWM1)
    TSW
    10~13
    CLK0
    (TSWM1)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    LN0
    (IMG0/IMG1)from
    LN DTIfrom
    LN DTI
    32M, FH+WFH
    PLO ACT32M, FH+WFH
    PLO ACT
    (BWB)32M, FH+WFH
    PLO ACT
    (BWB)
    64K+FH, WFH
    TSW ACT
    (Cable)64K+FH, WFH
    TSW ACT
    (Cable)
    PLO 1
    (TSWM0)
    TSW
    10~13
    PLO 0
    (TSWM0)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    LN3
    (IMG0/IMG1)
    32M, FH+WFH
    PLO ACT
    PLO 1
    (TSWM0)
    TSW
    10~13
    PLO 0
    (TSWM0)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    TSW00 TSW03HSW10 OSC64K+8K
    (BWB)
    (BWB)
    CLK, FH, WFH
    ACT, ALM
    PLO 0
    DTI0 DCS0 (MDF) DCS1123
    PLO 1
    SEL
    PLL
    Drv
    HSW11
    TSW10 TSW13
    SEL
    PLL
    Drv
    OSC
    ~
    ~~
    ~ 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 168
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    2. Mounting Location/Condition
    This circuit card can be mounted in the shaded slots shown below.
    Mounting ModuleISWM
    00 01 02 03 04 05 06 07 0809 10 11 1213 14 15 16 17 18 19
    00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 2021 2223
    PLO (#0) PLO (#1)
    Mounting ModuleTSWM0 (IMG1)
    PLO (#0) PLO (#1) 
    						
    							ND-70182 (E) CHAPTER 3
    Page 169
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    3. Face Layout of Lamps, Switches, and Connectors
    The face layout of lamps, switches, and connectors are shown in Figure 3-11.
    Figure 3-11   Face Layout of PH-CK16-A (PLO)
    1   2  3  4  
    1   2    
    SW11
    SW10SW12
    MB OPE
    1   2  3  4  5  6  7  8 
    MJ
    MN
    SYNC
    ICK
    CKPKG
    ALM0
    ALM1
    PALM
    SW01
    SW02
    SW03
    12345678 12345678 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 170
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    4. Lamp Indications
    Lamp indications for this circuit card are shown in the table below:
    Note:This lamp is effective when this card is mounted in TSWM0 of the IMX-U system.
    5. Switch Settings
    Standard settings for switches on this circuit card are shown in the table below.
    LAMP NAME COLOR STATE
    OPE Green Remains lit while this circuit card is in active state.
    MJ RedLights when the following MJ fault has occurred: 
    All of the clock supply routes have failed when the system operates as the clock 
    subordinate office
    32.768 MHz output clock failure (including CLK card)
    8 KHz output clock failure (including CLK card)
    Input Frame Pulse (FP) failure (FP is supplied by the SYNC card)  Internal OSC 
    (±5 ppm deviation) has failed when the system operates as the clock source office
    MN RedLights when the following MN fault has occurred:
    One or more (but not all) DTI/DCS clock supply route has failed 
    Drifting failure 
    Internal OSC (±5 ppm deviation) failure
    SYNC Green Remains lit while the system is synchronized with the network.
    ICK Green Lights when the internal oscillator is operating normally.
    CKPKG
    NoteGreen Lights when the CLK card in TSWM1 is in normal operation.
    ALM0
    NoteRed Lights when clock failure has occurred in the CLK card.
    ALM1
    NoteRed Lights when FH failure has occurred in the CLK card.
    PALM Red Remains lit when the On-Board Power Supply is abnormal.
    SWITCH 
    NAMESETTINGSTANDARD 
    SETTINGMEANING
    MBUP Circuit card Make-busy.
    DOWN×Circuit card Make-busy cancel.
    SW03 1 - F 1 Fixed to “1. 
    						
    							ND-70182 (E) CHAPTER 3
    Page 171
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    Note:
    When this card is used in the 4-IMG or ISWM of the IMX-U system, specify the clock source (DCS or DTI)
    according to the clock network configuration for the office.
    Note 1:This standard setting is applicable when this card is mounted in TSWM0 of the IMX-U system.
    SWITCH 
    NAMESWITCH
    NO.SETTINGSTANDARD 
    SETTINGMEANING
    SW01
    Note1ON
    ×    Note 1Clock subordinate office.
    OFF Clock source office.
    2ON
    ×    Note 1Digital Clock Supply route zero (DCS 0) is used.
    OFF Digital Clock Supply route zero (DCS 0) is not used.
    3ON
    ×    Note 1Digital Clock Supply route one (DCS 1) is used.
    OFF Digital Clock Supply route one (DCS 1) is not used.
    4ON8 KHz of Frame Head signals are extracted from the DCS sig-
    nals (which is composed of 64 KHz + 8 KHz).
    OFF
    ×    Note 18 KHz of Frame Head signals are not extracted from the DCS 
    signals (which is composed of 64 KHz + 8 KHz).
    5ONWhen clock source failure has occurred in all supply routes, 
    the PLO outputs the original clock of the internal oscillator.
    OFF×When clock source failure has not occurred, the PLO keeps on 
    outputting the current phase clock.
    6ON
    ×    Note 1T h i s  c i r c u i t  c a r d  i                                                                                                                                                                                                                                                                                          
    s associated with SYNC (PA-CK11) card.
    OFFThis circuit card is not associated with SYNC (PA-CK16 
    WCS) card.
    7ON A-law CODEC is used for Music-on-Hold.
    OFF×µ-law CODEC is used for Music-on-Hold.
    8OFF ×Fixed OFF (Not used). 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 172
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    Note:
    When this card is mounted in TSWM0 of the IMX-U system, the DCS clock from the ISW is used. The DTI
    clock can also be used as an alternate clock supply route in case of DCS clock failure.
    SWITCH 
    NAMESWITCH
    NO.SETTINGSTANDARD 
    SETTINGMEANING
    SW02
    Note1ON DIU 0 is used as the DTI clock supply route zero.
    OFF DIU 0 is not used.
    2ON DIU 1 is used as the DTI clock supply route one.
    OFF DIU 1 is not used.
    3ON DIU 2 is used as the DTI clock supply route two.
    OFF DIU 2 is not used.
    4ON DIU 3 is used as the DTI clock supply route three.
    OFF DIU 3 is not used.
    5ON×1.5 M clock for DIU 0.
    OFF 2 M clock for DIU 0.
    6ON×1.5 M clock for DIU 1.
    OFF 2 M clock for DIU 1.
    7ON×1.5 M clock for DIU 2.
    OFF 2 M clock for DIU 2.
    8ON×1.5 M clock for DIU 3.
    OFF 2 M clock for DIU 3.
    SW101ON  External hold tone source is used via FM lead.
    OFF×MUSIC ROM is used as the hold tone.
    2ON CLK card is not used.
    OFF CLK card is used. 
    						
    							ND-70182 (E) CHAPTER 3
    Page 173
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    SWITCH 
    NAMESWITCH
    NO.SETTINGSTANDARD 
    SETTINGMEANING
    SW111
    2
    3
    4
    SW121
    2
    3
    4ON Not used
    OFF×Not used
    5
    MUSIC (CH1) selection. The music varies depending on the melody IC located on this circuit 
    card. 6
    7
    8ON Not used
    OFF×Not used
    SW11-1 SW11-2Impedance of the External 
    Music Source 0 (FM 0)
    OFF OFF 600 Ω
    ON OFF 8.2 Ω
    OFF ON 47K Ω
    SW11-3 SW11-4Impedance of the External 
    Music Source 1 (FM 1)
    OFF OFF 600 Ω
    ON OFF 8.2 Ω
    OFF ON 47K Ω
    SW12-1 SW12-2 SW12-3 MUSIC
    OFF OFF OFF Für Elise
    ON OFF OFF Maiden’s prayer
    Not Used ON OFF Buzzer
    Not Used OFF ON Chime 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 174
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    6. External Interface
    PLO leads appear on the LT connectors labeled EXCLK0 and EXCLK1.
    PLO mounting slots
    The PLO card is mounted in Slots 21 and 23 of TSWM.
    LT cable connectors
    Connect the LT cables to the connectors labeled EXCLK0 and EXCLK1 on the TSWM backplane.
    Figure 3-12   PLO Pin Assignments for Receiving Clock (4 IMG System) (1/2) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
    EXCLK0EXCLK1
    PLO
    PLO
    TSW Front View
    TSWM
    EXCLK0EXCLK1
    TSWMBackplane 
    						
    							ND-70182 (E) CHAPTER 3
    Page 175
    Revision 4.0
    PH-CK16-A
    Phase Lock Oscillator
    EXCLK0/EXCLK1 connector Pin Assignment
    Pins are assigned as follows on the EXCLK0/EXCLK1 connectors. When the clock is distributed from a
    digital interface, use one pair of DIUxxx in one of the 4 inputs. (There are a maximum of 4 inputs.) DIU
    leads have the following precedence: DIU0xx (high) 
    ➝ DIU3xx (low).
    Figure 3-12   PLO Pin Assignments for Receiving Clock (4 IMG System) (2/2)
    PLO input leads appear on the LT connectors labeled EXCLK0 and EXCLK1.
    PLO mounting slots
    The PLO card is mounted in Slots 09 and 13 of ISWM.
    34PH ISWM EXCLK CA-A
    34PH ISWM EXCLK CA-A
    REAR VIEW
    EXCLK0EXCLK1TSWM
    MDF
    Installation Cable To Digital Interface and/or DCS
    34PH ISWM EXCLK CA-A Cable Lead Location
    26
    27
    28
    29
    30
    31
    32
    33
    34
    35
    36
    37
    381
    2
    3
    4
    5
    6
    7
    8
    9
    10
    11
    12
    13 FM1
    FM0
    DIU3B
    DIU2B
    DIU1B
    DIU0B
    DCSB
    SYN1B
    SYN0BE
    E
    DIU3A
    DIU2A
    DIU1A
    DIU0A
    DCSA
    SYN1A
    SYN0A
    00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 23EXCLK0EXCLK1
    PLO
    PLO
    Front View
    ISWM 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx Circuit Card Manual