Home > NEC > Communications System > NEC Neax 2400 Imx Circuit Card Manual

NEC Neax 2400 Imx Circuit Card Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx Circuit Card Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							CHAPTER 3 ND-70182 (E)
    Page 146
    Revision 4.0
    PA-CFTB
    8-par ty Conference Trunk
    PA-CFTB
    8-party Conference Trunk
    1. General Function
    The PA-CFTB (CFT) circuit card provides an interface for establishing a conference, which is made up of
    a maximum of eight parties.
    A maximum of seven Tie Lines can participate in a conference when the associated trunks can receive an
    answer signal and a release signal from the distant switching system. On the other hand, in the case of a
    C.O. line, one C.O. line can be connected even if the public switching system cannot send an answer signal
    and/or release signal. Note that a Tie Line and a C.O. Line cannot take part in a conference at the same time.
    The card adopts “N-1 addition” method for establishing a conference.
    Note:This circuit card is used for following features:
    Station-Controlled Conference (Refer to Feature Programming Manual) [S-56]
    Attendant-Controlled Conference (Refer to Feature Programming Manual) [A-2]
    Add On Conference-8 Party (Refer to Feature Programming Manual) [A-121]
    Group Call-Automatic Conference (20-party) (Refer to Wireless System Manual)
    Figure 3-1   Location of PA-CFTB (CFT) within the System
    NETWORKAnswer/Release Signal →
    Conferee
    Conference
    Originator
    CPU Local I/O Bus
    GT INT SW INT PA-CFTB
    7
    6
    5
    4
    3
    2
    1
    0
    PCM INTVPROC
    PCM INT: PCM Interface
    VPROC: Voice Processor Block
    TLT
    TLT
    LC
    LC
    CH
    This diagram shows an example of a “Preset” conference involving Tie Line connections. 
    						
    							ND-70182 (E) CHAPTER 3
    Page 147
    Revision 4.0
    PA-CFTB
    8-party Conference Trunk
    2. Mounting Location/Condition
    The PA-CFTB (CFT) card can be mounted in any universal slots as shown below.
    Note: Indicates universal slots for line/trunk circuit cards.
    00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
    Mounting ModulePIM 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 148
    Revision 4.0
    PA-CFTB
    8-par ty Conference Trunk
    3. Face Layout of Lamps, Switches, and Connectors
    The face layout of lamps, switches, and connectors on this circuit card is shown in Figure 3-2.
    Figure 3-2   Face Layout of PA-CFTB (CFT)
    4. Lamp Indications
    The contents of lamp indications of this circuit card are shown in the table below.
    LAMP
    NAMECOLOR STATE
    OPE Green Remains lit while this circuit card is operating.
    N-OPE Red Remains lit while this circuit card is in make-busy state.
    BL0
    BL7Red BL-lamp remains lit while the corresponding circuit is busy.
    Flash BL-lamp flashes when the corresponding circuit is busy.
    OPE
    N-OPE
    MB SW2
    SW1
    SW0
    BL7
    BL0
    ~ 
    						
    							ND-70182 (E) CHAPTER 3
    Page 149
    Revision 4.0
    PA-CFTB
    8-party Conference Trunk
    5. Switch Settings
    Standard settings of switches on this circuit card are shown in the table below.
    SWITCH
    NAMESWITCH
    NO.SETTINGSTANDARD
    SETTINGMEANING
    MBUP Circuit card make busy
    DOWN
    ×Circuit card make busy cancel
    SW01ON
    ×Fixed in the system
    OFF
    2ON
    ×Fixed in the system
    OFF
    3ON
    ×Fixed in the system
    OFF
    4ON
    ×Fixed in the system
    OFF
    5ON
    ×Fixed in the system
    OFF
    6ON
    ×Fixed in the system
    OFF
    7ON
    OFF
    ×Fixed in the system
    8ON
    OFF
    ×Fixed in the system
    12345678 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 150
    Revision 4.0
    PA-CFTB
    8-par ty Conference Trunk
    SWITCH
    NAMESWITCH
    NO.SETTINGSTANDARD
    SETTINGMEANING
    SW
    1
    1ON×Fixed in the system
    OFF
    2ON
    ×Fixed in the system
    OFF
    3ON
    ×Fixed in the system
    OFF
    4ON
    ×Fixed in the system
    OFF
    5ON
    ×Fixed in the system
    OFF
    6ON
    ×Fixed in the system
    OFF
    7ON
    ×Fixed in the system
    OFF
    8ON
    OFF
    ×Fixed in the system
    SW21ON
    ×µ-law PCM encoder
    OFF A-law PCM encoder
    2ON Conference connection is set up by PB tel.
    OFF Conference connection is not set up by PB tel.
    3ONWhen port Microprocessor (PM) is SP-388, 
    SP-457, SP-863, SP-990, SP-1114.
    OFFWhen Port Microprocessor (PM) is SP-519, 
    SP-1141.
    4OFF
    ×Not used
    5OFF
    ×Not used
    6OFF
    ×Not used
    12345678
    12345678 
    						
    							ND-70182 (E) CHAPTER 3
    Page 151
    Revision 4.0
    PA-CFTB
    8-party Conference Trunk
    6. Switch Setting Sheet
    SWITCH 
    NAMESWITCH
    NO.SETTINGSTANDARD
    SETTINGMEANING
    SW27ONCFTB Insertion Loss (PAD value) Setting
    OFF
    8ON
    OFF
    MODULESLOT
    NO.SWITCH
    NAMESWITCH SHAPE REMARKS
    PIMSW0
    SW1
    SW2
    MB
    DOWNCircuit card make busy cancel
    SW2-7 SW2-8 PAD [dB]
    OFF OFF 0
    OFF ON 3
    ON OFF 6
    ON ON 9
    12345678ON
    12345678ON
    12345678ON 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 152
    Revision 4.0
    PA - C K 1 4
    Oscillator
    PA-CK14
    Oscillator
    1. General Function
    The PLO block of the TSW card generates its base clock signals, and adjusts their phase with the source
    clock signals so the PLO can send the synchronized clock signals to the TSW. When the 1 IMG system is
    a clock-subordinate-office of the digital network, the base clock accuracy of the PLO/ PH-SW10 (±5 ppm
    deviation) is sufficient. However, the more high-precision base clock signals are required at the clock-
    source-office, as this circuit card provides --- PA-CK14 (±0.3 ppm deviation). When this circuit card is
    mounted, the 1 IMG system selects the PA-CK14 (OSC) clocks as the base clock of the PLO. 
    Figure 3-3   Location of PA-CK14 (OSC) Card in the System
    SEL
    SEL
    TDSW
    MUX0PLOSEL
    SEL
    TDSW
    MUX0PLO
    BWB BWB BWBBWB
    OSC OSC DTI 0 CLOCK SOURCE
    DTI 1 CLOCK SOURCE
    DTI 2 CLOCK SOURCE
    DTI 3 CLOCK SOURCE
    DSC 0DSC 1
    FRONT CABLES FRONT CABLES
    MUX1 MUX2 MUX3 MUX1 MUX2 MUX3
    LC/TRK LC/TRK LC/TRK LC/TRK LC/TRK LC/TRK LC/TRK LC/TRK
    DSC1
    DSC0 
    						
    							ND-70182 (E) CHAPTER 3
    Page 153
    Revision 4.0
    PA-CK14
    Oscillator
    2. Mounting Location/Condition
    The PA-CK14 (OSC) is located in PIM0. The card mounted in Slot 09 works as the primary OSC, 17 for
    the secondary OSC.
    Note:This card occupies two slots.
    3. Face Layout of Lamps, Switches, and Connectors
    The face layout of lamps, switches, and connectors is shown below.
    Figure 3-4   Face Layout of PA-CK14 (OSC) Card 00 01 02 03 04 05 06 07 08
    09 10 11 12 13 14 15 1617 18 19 20 21 22 23
    Mounting ModulePIM
    OSC#0 OSC#1
    PIM0
    CLKOUT 0
    CLKOUT 1
    MB 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 154
    Revision 4.0
    PA - C K 1 4
    Oscillator
    4. Lamp Indications
    Lamp indications for this circuit card are shown in the table below.
    5. Switch Settings
    Standard settings for switches on this circuit card are shown in the table below.
    6. External Interface
    Since the base clock signals are delivered through the printed-wiring on the Back Wired Board (BWB) of
    PIM 0, this circuit card does not require any external cabling.
    7. Switch Setting Sheet
    LAMP NAME COLOR STATE
    CLKOUT0 Green Lights when OSC card delivers the clock signals to TSW#0.
    CLKOUT1 Green Lights when OSC card delivers the clock signals to TSW#1.
    SWITCH 
    NAMESETTINGSTANDARD 
    SETTINGMEANING
    MBON Make-busy of the circuit card.
    OFF×Normal setting.
    SWITCH NAME SWITCH SHAPE REMARKS
    MB
    ON 
    						
    							ND-70182 (E) CHAPTER 3
    Page 155
    Revision 4.0
    PH-CK16
    Phase Lock Oscillator
    PH-CK16
    Phase Lock Oscillator
    1. General Function
    This circuit card, used together with a direct digital interface circuit card, sets up network synchronization
    with the network. With this circuit card, the 4 IMG system can be a clock subordinate office of the digital
    network. As seen in the figure below, the PLO can be redundant regardless of the system switching network
    selection.
    Figure 3-5   Location of PH-CK16 (PLO) Card in the System
    TDSW00TDSW01TDSW02TDSW03
    SEL
    PLL PLL
    PLO #0 PLO #1OSC OSC
    TDSW10 TDSW11 TDSW12 TDSW13SEL 34PH EXCLK CA-A 34PH EXCLK CA-A MDFMDF
    BWB BWB
    BWB BWB
    DTI 0 CLOCK SOURCE
    DTI 1 CLOCK SOURCE
    DTI 2 CLOCK SOURCE
    DTI 3 CLOCK SOURCE
    DCS 0DCS 1 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx Circuit Card Manual