Home > NEC > Communications System > NEC Neax 2400 Imx Circuit Card Manual

NEC Neax 2400 Imx Circuit Card Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx Circuit Card Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							CHAPTER 3 ND-70182 (E)
    Page 206
    Revision 4.0
    PH-CK17-A
    Phase Lock Oscillator
    Figure 3-31 shows an example of distributing clock from a digital interface. This figure assumes that the Digital
    Trunk POUT leads are used as the first clock distribution route.
    Figure 3-31   Cable Connection Diagram (4-IMG System/LN) for Receiving Clock from Digital Interface
    DIU0A1
    DIU0B1
    DIU1A1
    DIU1B1
    DIU2A1
    DIU2B1
    DIU3A1
    DIU3B1
    DIU0A0
    DIU0B0
    DIU1A0
    DIU1B0
    DIU2A0
    DIU2B0
    DIU3A0
    DIU3B0
    RA
    RB
    TA
    TB
    POUT A
    POUT BPCM Cable (2P) to other nodePCM
    Carrier
    Equipment
    DSU
    CLK
    Note 1:Note 2 Note 1
    PLO has a maximum of 4 inputs. DIU0xx leads are used for the 1st clock distribution routes.
    DIU3xx leads are used for the 4th. The first input has the highest priority.
    Note 2:The connection is required for a dual PLO system.
    MDF
    maximum 100
    meters (330 feet)
                     (24AWG)
    Installation Cable LT Connector
    Installation Cable
    Installation Cable
    EXCLK1PLO#1
    EXCLK0PLO#0 Digital
    Interface
    IMG1
    maximum 200 meters (660 feet) (24 AWG) 
    						
    							ND-70182 (E) CHAPTER 3
    Page 207
    Revision 4.0
    PH-CK17-A
    Phase Lock Oscillator
    Figure 3-32   Connection of External Music-On-Hold
    7. Switch Setting Sheet
    SWITCH NAME SWITCH SHAPE
    MB
    SW01
    SW02
    SW03
    SW10
    SW11
    SW12
    ISW-LN PLO CA-A cable/
    34PH ISWM EXCLK CA-A
    Pin Assignment
    PIN
    No.
    26
    27
    28
    29
    30
    31
    32
    33LEAD
    NAME
    FM1
    FM0LEAD
    NAME
    E
    E PIN
    No.
    1
    2
    3
    4
    5
    6
    7
    8
    9MUSIC
    SOURCE MDFISW-LN PLO CA-A /
    34PH ISWM EXCLK CA-A and
    Installation Cable(25P)
    Multiple connections between the systems 0 and 1
    are required on the MDF. Note
    Note:
    FM1 is not used at this time.
    ON
    1234ON5678
    1234ON5678
    12ON
    1ON234
    1234ON5678 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 208
    Revision 4.0
    PH-CK18
    Clock
    PH-CK18
    Clock
    1. General Function
    This circuit card is used for the Local Node of the IMX-U system. The main function of this circuit card is
    to supply basic clock signals to the system. This card receives clock signals from the Phase Lock Oscillator
    (PLO) located in TSWM0 of IMG1, distributing the following signals to the Time Division Switch (TSW)
    located in TSWM1 of IMG2.
    32.768 MHz CLK
    8 KHz FH
    5 msec ×  “n” FH (for Wireless System) 
    						
    							ND-70182 (E) CHAPTER 3
    Page 209
    Revision 4.0
    PH-CK18
    Clock
    Figure 3-33   Location of PH-CK18 (CLK) 
    LN0
    (IMG2/IMG3)LN3
    (IMG2/IMG3)
    32M, FH+WFH
    PLO ACT32M, FH+WFH
    PLO ACT
    CLK1
    (TSWM1)
    TSW
    10~13
    CLK0
    (TSWM1)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    HSW00 ISW
    HSW01
    CLK1
    (TSWM1)
    TSW
    10~13
    CLK0
    (TSWM1)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    LN0
    (IMG0/IMG1)from
    LN DTIfrom
    LN DTI
    32M, FH+WFH
    PLO ACT32M, FH+WFH
    PLO ACT
    (BWB)32M, FH+WFH
    PLO ACT
    (BWB)
    64K+FH, WFH
    TSW ACT
    (Cable)64K+FH, WFH
    TSW ACT
    (Cable)
    PLO 1
    (TSWM0)
    TSW
    10~13
    PLO 0
    (TSWM0)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    LN3
    (IMG0/IMG1)
    32M, FH+WFH
    PLO ACT
    PLO 1
    (TSWM0)
    TSW
    10~13
    PLO 0
    (TSWM0)
    TSW
    00~03
    MUX
    (System1)MUX
    (System0)
    LC/TRK
    TSW00 TSW03HSW10 OSC64K+8K
    (BWB)
    (BWB)
    CLK, FH, WFH
    ACT, ALM
    PLO 0
    DTI0 DCS0 (MDF) DCS1123
    PLO 1
    SEL
    PLL
    Drv
    HSW11
    TSW10 TSW13
    SEL
    PLL
    Drv
    OSC
    ~
    ~~
    ~ 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 210
    Revision 4.0
    PH-CK18
    Clock
    2. Mounting Location/Condition
    Mounting locations for this circuit card are shown below.
    3. Face Layout of Lamps, Switches, and Connectors
    The face layout of each lamp and switch on this circuit card is shown in Figure 3-34.
    Figure 3-34   Face Layout of PH-CK18 (CLK) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20
    21 2223
    Mounting ModuleTSWM1 (IMG2)
    CLK (#1)
    CLK (#0)
    MB OPE
    ALM0
    ALM1
    PALM 
    						
    							ND-70182 (E) CHAPTER 3
    Page 211
    Revision 4.0
    PH-CK18
    Clock
    4. Lamp Indications
    Lamp indications for this circuit card are shown below:
    5. Switch Settings
    Switch settings for this circuit card are shown below.
    LAMP COLOR  MEANING
    OPE Green Lights when this circuit card is in ACT state.
    ALM 0 Red Lights when clock signal failure has occurred.
    ALM 1 Red Lights when Frame Head signal failure has occurred.
    PALM Red Lights when the On Board Power Supply failure has occurred.
    SWITCH 
    NAMESETTINGSTANDARD 
    SETTINGMEANING
    MBON Circuit card Make-busy.
    OFF×Circuit card Make-busy cancel. 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 212
    Revision 4.0
    PH-CK18
    Clock
    6. External Interface
    Figure 3-35   LT Connector Lead Location (ISW-LN0)
    7. Switch Setting Sheet
    SWITCH NAME SWITCH SHAPE REMARKS
    MB
    PIM
    CLK00
    (Slot No.08) CLK10
    (Slot No.12)
    TSWM1
    TSWM0 ISWM
    Installation Cable DIU Connection Note
    MDF
    To Digital Interface and/or DCS
    EXCLK0
    (Slot No.21)
    PLO CLOCK0
    (Slot No.21)
    EXCLK1
    (Slot No.23)
    PLO CLOCK1
    (Slot No.23)PLO CLOCK0
    (Slot No.21)PLO CLOCK1
    (Slot No.23)
    ISW-LN PLO CA-A
    PLO-CLK CA-A DCS Connection
    Note:For DIU connection route diagram, see the figure on the next page.
    261 LEAD
    NAMELEAD
    NAME
    272
    283 PIN
    No. PIN
    No.
    294
    305
    316
    327
    338
    349
    3510 DIU 3B
    DIU 2BDIU 3A
    DIU 2A
    DIU 1B
    DIU 1A
    DIU 0B
    DIU 0A
    ON 
    						
    							ND-70182 (E) CHAPTER 3
    Page 213
    Revision 4.0
    PA - C S 0 8
    Hotel Attendant Interface
    PA - C S 0 8
    Hotel Attendant Interface
    1. General Function
    This circuit card is the Hotel Attendant Console (Hotel ATTCON) interface card that supports the interface
    function for the Hotel ATTCON (maximum two sets of Hotel ATTCON per card), PM function (controlling
    of Hotel ATTCON and exchanging of control commands with the CPU), PB/DP sending function (sending
    of PB signals or DP signals under control of the PM), receiving data (Hotel ATTCON Call Termination
    Information) link interface function, etc.
    Figure 3-36   Location of PA-CS08-B (HMATI) Card in the System
    2. Mounting Location/Condition
    The PA-CS08-B (HMATI) card can be mounted in the shaded slots as shown below.
    CPU GTTDSW
    MUX
    2M PCM Highway
    PM Bus
    ATTENDANT
    CONSOLE (×2)
    : Control Line
    : Speech Path
    IO Local Bus : Input Output Local Bus
    PM Bus : Port Microprocessor Bus
    HMATI
    00 01 02 03 04 05 06 07 08 09 10 1112 13 14 15 16 17 18 19 20 21 2223
    Mounting ModulePIM
    HMATI
    HMATI 
    						
    							CHAPTER 3 ND-70182 (E)
    Page 214
    Revision 4.0
    PA - C S 0 8
    Hotel Attendant Interface
    3. Face Layout of Lamps, Switches, and Connectors
    The face layout of lamps, switches, and connectors on this circuit card is shown in Figure 3-37.
    Figure 3-37   Face Layout of HMATI Card
    4. Lamp Indications
    Lamp indications for this circuit card are shown in the table below.
    LAMP COLOR  STATE
    OPE Green Remains lit while this circuit card is operating.
    N-OPE Red Remains lit while this circuit card is in Make-busy state.
    BLS0
    BLS1Red Lights when the corresponding circuit is busy.
    BlinkBlinks when the corresponding circuit is busy.
    Note:The lamp also blinks when dial signals are being sent out.
    OPE
    N-OPE
    MB
    FU0 (Note
    )
    SW11
    BLS1
    BLA1
    BLA0
    SW04
    SW03
    SW02
    SW08
    SW07
    SW09
    SW12
    3210
    FU1 (Note)
    BLS0
    Note:When extracting/inserting this card, care should be taken as to the FU0, FU1.
      
    ➀ MB key → ON ➁ Remove the FU0 and FU1. ➂ Extract this card.
      
    ➀ Mount this card without the FU0 and FU1. ➁ Plug in the FU0 and FU1. 
    ➂ MB key → OFF 
    						
    							ND-70182 (E) CHAPTER 3
    Page 215
    Revision 4.0
    PA - C S 0 8
    Hotel Attendant Interface
    5. Switch Settings
    Standard settings for various switches on this circuit card are shown in the table below.
    BLA0
    BLA1Red Lights when the corresponding circuit is busy.
    Blink Blinks when the corresponding circuit is in Make-busy state.
    SWITCHSWITCH 
    NO.SETTINGSTANDARD 
    SETTINGMEANING
    MBUP Circuit card Make-busy.
    DOWNCircuit card Make-busy cancel.
    SW02 (TAS0)
    SW03 (TAS1)1
    2
    3
    4
    SW041ON  ×Fixed
    2OFF  ×Fixed
    3ON  ×Fixed
    4OFF  ×Fixed
    SW07 (TAS0)
    SW08 (TAS1)1
    2
    3
    4 LAMP COLOR  STATE
    SETTING OF TAS SIGNALLING SYSTEM
    SWITCH TAS (A WIRE) TAS (B WIRE)
    1-48VG
    2CRG
    3GG
    4 LOOP LOOP
    SETTING OF TAS CURRENT LIMIT RESISTANCE
    SW7-1/
    SW8-1SW7-2/
    SW8-2SW7-3/
    SW8-3SW7-4/
    SW8-4RESISTANCE
    ON
    OFF
    ON
    OFF
    ON
    OFF
    ON
    OFFON
    ON
    OFF
    OFF
    ON
    ON
    OFF
    OFFON
    ON
    ON
    ON
    OFF
    OFF
    OFF
    OFFOFF
    OFF
    OFF
    OFF
    OFF
    OFF
    OFF
    OFF0 Ω
    ΩΩ Ω
    200 Ω
    ΩΩ Ω
    390 Ω
    ΩΩ Ω
    590 Ω
    ΩΩ Ω
    820 Ω
    ΩΩ Ω
    1020 Ω
    ΩΩ Ω
    1210 Ω
    ΩΩ Ω
    1410 Ω
    ΩΩ Ω 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx Circuit Card Manual